Supermicro SuperStorage L-Serie User manual

http://www.supermicro.com MNL-xxxx- QRG
Board Layout
SuperStorage L-Serie Quick Reference Guide
Rear View
CPU Installation
Beep Codes
LED Indicator

Heatsink Installation
1. Place heatsink on top of installed CPU
2. Line up the four screws to socket
3. Push down heatsink and screw down as shown
(cross pattern, in order: A, C, B, D)
4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten
each screw, to avoid damaging the system
MEMORY
Caution
Top View of DDR3 Slot
Release Tab Release Tab
Note: Notch should align
with the receptive key
point on the slot.
NotchNotch
Front View
Align CPU to socket;
install CPU straight down
NOTE:
Do not bend pin inside socket

!
FAN5
T-SGPIO2
JSD1
JBT1
JD1
CPU1
CPU2
CPU2
CPU1
CPU2
CPU1
P2-DIMME1 P2-DIMMF2 P2-DIMMF1
P2-DIMMG2
P2-DIMMG1
P2-DIMMH2 P2-DIMMH1
P1-DIMMA2
P1-DIMMA1
P1-DIMMB2
P1-DIMMB1
P1-DIMMC1 P1-DIMMC2
P1-DIMMD1
P1-DIMMD2
SLOT1 PCI-E 3.0 X8
SLOT2 PCI-E 3.0 X8
SLOT3 PCI-E 3.0 X8
SLOT4 PCI-E 3.0 X8
SLOT5 PCI-E 3.0 X8
CMOS CLEAR
SLOT6 PCI-E 3.0 X8
SP1
CPU2
CPU2
CPU2
JPW1
P2-DIMME2
JPW3
L-SAS4~7 L-SAS0~3
Intel
PCH
JPS1
CPU1
X9DRD-7JLN4F
Description
No.
1234 5
87
JBOD Expansion Port
CPU1 Slot2 PCI-E 3.0 x8
CPU2 Slot3 PCI-E 3.0 x8
CPU2 Slot4 PCI-E 3.0 x8
CPU2 Slot5 PCI-E 3.0 x8
CPU1 Slot6 PCI-E 3.0 x8
P1-DIMMA1(Blue)/P1-DIMMA2 slot
P1-DIMMB1 (Blue)/P1-DIMMB2 slot
P1-DIMMC1 (Blue)/P1-DIMMC2 slot
P1-DIMMD1 (Blue)/P1-DIMMD2 slot
P2-DIMME1 (Blue)/P2-DIMME2 slot
P2-DIMMF1 (Blue)/P2-DIMM F2 slot
P2-DIMMG1 (Blue)/P2-DIMM G2 slot
P2-DIMMH1 (Blue)/P2-DIMM H2 slot
CPU1 / P1 install first / minimum requirement
CPU2
SATA 3 Ports 0~1 (from Intel PCH)
SATA 2 Ports 2~5 (from Intel PCH)
SAS 2.0 ports 0~3, 4~7 (from LSI SAS 2308 Controller)
JBT1 = CMOS Reset
SATA DOM Power
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
6
910 15
11 12 14 13
16
19
18
21
20
17
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING:
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
CAUTION:
Always be sure all power supplies for this system have
the same power output. If mixed power supplies are
installed, the system will not operate.
For more information go to :
http://www.supermicro.com/support

!

!

!
Normal Operation
Drive Failure
Rebuilding to Drive
Drive Assigned as a Hot Spare
Slot Identify command
has been issued from controller
Indication
LED State
OFF
Solid ON
Slow Blink (1 Hz)
2 Fast Blink, Pause (repeats)
Fast Blink (4 Hz)
Description
No.
3.5” Drive Module
2.5” Drive Module
Blue/Activity
Red/Status
Drive RED LED Indicator
3
15
47
6
2
1
2
3
4
5
6
7
COM Port1
Dedicated IPMI LAN
USB 0/1/2/3 Ports
LAN 1/2/3/4 Ports
VGA Port
UID Button
Dual JBOD Expansion port*
*SSG-6027R-E1R12L features a single expansion port
BIOS Beep Codes
Beep Code/LED Message Description
1 beep Refresh Circuits have been reset.
(Ready to power up)
5 short beeps + 1 long
beep
Memory
5 long beeps + 2 short
beeps
Display memory
read/write status
Video adapter missing or with
faulty memory
1 continuous beep System System overheat
No memory detected
DIMM Module Population Tables
Processors and their Corresponding Memory Slots
tolSyromeMgnidnopserroC#UPC
CPU 1 (P1-) A1 B1 C1 D1 A2 B2 C2 D2 A3 B3 C3 D3
CPU2 (P2-) E1 F1 G1 H1 E2 F2 G2 H2 E3 F3 G3 H3
Processor and Memory Module Population
Number of
CPUs+DIMMs
CPU and Memory Population Configuration Table
(For memory to work properly, please install DIMMs as shown below.)
1 CPU &
3 DIMMs
CPU1
P1-A1/P1-B1/P1-C1
1 CPU &
6 DIMMs
CPU1
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2
1 CPU &
9 DIMMs
CPU1
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3
1 CPU &
12 DIMMs
CPU1
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3/P1-B3/P1-C3/P1-D3
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1
P2-E1/P2-F1/P2-G1
2 CPUs &
12 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2
2 CPUs &
16 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2
2 CPUs &
18 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2/P2-E3
2 CPUs &
24 DIMMs
CPU1/CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3/P1-B3/P1-C3/P1-D3
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2/P2-E3/P2-F3/P2-G3/P2-H3
Screw #B
Screw #D
Screw #A
Screw #C
Chassis Front Panel LED Indicator Definition
Solid Green/Power is On
Flash Green/Onboard SAS/SATA Drive Activity
Flash Green/Network Connectivity
Flash Green/Network Connectivity
Flash Red/Fan Failure; Solid Red/Over Temperature
Flash Red/Power Supply Failure
State/Indication
Component
Power
Onboard SATA
LAN1
LAN2
Temperature/Fan
Power Failure
Please refer to the user manual for more details on memory types, speeds and configurations