Supero 1017C-TF User manual

SUPERSERVER 1017C-TF
SUPER ®
USER’S MANUAL
1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITHTHE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro-
ductive harm.
Manual Revision 1.0
Release Date: February 15, 2011
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2011 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 1017C-TF. In-
stallation and maintenance should be performed by experienced technicians only.
The SuperServer 1017C-TF is a high-end server based on the SC111LT-330CB 1U
rackmount chassis and the Super X9SCL-F single processor serverboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the X9SCL-F serverboard and
the SC111LT-330CB chassis, which comprise the SuperServer 1017C-TF.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 1017C-TF
into a rack and check out the server configuration prior to powering up the system.
If your server was ordered without processor and memory components, this chapter
will refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

SUPERSERVER 1017C-TF User's Manual
iv
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 1017C-TF.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X9SCL-F serverboard, including the
locations and functions of connections, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconfiguring the
serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC111LT-330CB server chassis.
You should follow the procedures given in this chapter when installing, removing or
reconfiguring SATA or peripheral drives and when replacing system power supply
modules and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications

v
Preface
Notes

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Motherboard Features.....................................................................................1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
Serial ATA........................................................................................................ 1-2
I/O Ports..........................................................................................................1-2
Graphics Controller......................................................................................... 1-2
1-3 Server Chassis Features ................................................................................1-3
System Power.................................................................................................1-3
PCI Expansion Slots....................................................................................... 1-3
Control Panel ..................................................................................................1-3
Cooling System...............................................................................................1-3
1-4 Contacting Supermicro....................................................................................1-5
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System.................................................................................... 2-1
2-3 Preparing for Setup.........................................................................................2-1
Choosing a Setup Location............................................................................. 2-1
Rack Precautions............................................................................................2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations....................................................................... 2-3
Ambient Operating Temperature................................................................2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ...................................................................................2-3
Circuit Overloading.....................................................................................2-3
Reliable Ground .........................................................................................2-3
2-4 Installing the System into a Rack ...................................................................2-4
Identifying the Sections of the Rack Rails...................................................... 2-4
Inner Rails.......................................................................................................2-4
Installing the Inner Rails ................................................................................2-5
Outer Rail Options .......................................................................................... 2-6
Installing the Outer Rails to the Rack............................................................. 2-6
Installing the Chassis into the Rack................................................................2-7
2-5 Checking the Serverboard Setup.................................................................... 2-8
2-6 Checking the Drive Bay Setup........................................................................ 2-9
SUPERSERVER 1017C-TF User's Manual

vii
Table of Contents
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Buttons..................................................................................... 3-1
Reset...............................................................................................................3-1
Power..............................................................................................................3-1
UID..................................................................................................................3-1
3-3 Control Panel LEDs ........................................................................................ 3-2
Universal Information LED.............................................................................. 3-2
NIC2................................................................................................................3-3
NIC1................................................................................................................3-3
HDD................................................................................................................. 3-3
Power..............................................................................................................3-3
3-4 Hard Drive Carrier LEDs................................................................................. 3-4
Chapter 4 System Safety
4-1 Electrical Safety Precautions.......................................................................... 4-1
4-2 General Safety Precautions............................................................................ 4-2
4-3 ESD Precautions.............................................................................................4-3
4-4 Operating Precautions ....................................................................................4-4
Chapter 5 Advanced Motherboard Setup
5-1 Handling the Motherboard ..............................................................................5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2 Processor and Heatsink Installation................................................................5-2
Installing the LGA1155 Processor .................................................................5-2
Installing a Passive CPU Heatsink .................................................................5-4
Removing the Heatsink................................................................................... 5-4
5-3 Connecting Cables..........................................................................................5-6
Connecting Data Cables................................................................................. 5-6
Connecting Power Cables .............................................................................. 5-6
Connecting the Control Panel......................................................................... 5-6
5-4 I/O Ports..........................................................................................................5-7
5-5 Installing Memory............................................................................................5-8
5-6 Adding PCI Cards......................................................................................... 5-10
5-7 Motherboard Details.......................................................................................5-11
5-8 Connector Definitions ...................................................................................5-13
5-9 Jumper Settings............................................................................................ 5-19
5-10 Onboard Indicators........................................................................................ 5-21
5-11 SATA Drive Connections............................................................................... 5-22

viii
5-12 Installing Drivers............................................................................................ 5-23
Supero Doctor III...........................................................................................5-24
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions ..................................................................................................... 6-1
6-2 Control Panel ..................................................................................................6-2
6-3 System Cooling...............................................................................................6-2
System Fan Failure......................................................................................... 6-3
Installing the Air Shroud.................................................................................. 6-5
6-4 Drive Bay Installation/Removal....................................................................... 6-5
Accessing the Drive Bays............................................................................... 6-5
Hard Drive Installation..................................................................................... 6-5
DVD Drive Installation..................................................................................... 6-7
6-5 Power Supply..................................................................................................6-9
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 4-1
7-2 Main Setup......................................................................................................4-2
7-3 Advanced Setup Configurations......................................................................4-4
7-4 Event Logs....................................................................................................4-15
7-5 IPMI Configuration (X9SCL-F/X9SCM-F Only)............................................. 4-16
7-6 Boot Settings ................................................................................................ 4-18
7-7 Security Settings........................................................................................... 4-19
7-8 Exit Options...................................................................................................4-20
Appendix A BIOS Error Beep Codes
Appendix B System Specifications
SUPERSERVER 1017C-TF User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 1017C-TF is a high-end server comprised of two main subsys-
tems: the SC111LT-330CB 1U server chassis and the X9SCL-F single processor
motherboard. Please refer to our web site for information on operating systems that
have been certified for use with the system (www.supermicro.com).
In addition to the motherboard and chassis, various hardware components have
been included with the 1017C-TF, as listed below:
 One slim DVD-ROM drive (DVM-PNSC-824B)
 Three sets of 4-cm counter-rotating fans (FAN-0086L4)
 One passive CPU heatsink (SNK-P0046P)
 Riser Cards: (see Section 5-6 for details)
One CSE-RR1U-E8 for one PCI-E 2.0 x8 card
 SATA Accessories
One SATA backplane (BPN-SAS-809TQ)
Four 2.5" hot-swap drive carriers (MCP-220-00047-0B)
 One rackmount kit (MCP-290-00050-0N)
 One CD containing drivers and utilities
 SuperServer 1017C-TF User's Manual
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 1017C-TF User's Manual
1-2 Motherboard Features
At the heart of the SuperServer 1017C-TF lies the X9SCL-F, a single processor
motherboard based on Intel's C202 chipset. Below are the main features of the
X9SCL-F (see Figure 1-1 for a block diagram of the chipset).
Processors
The X9SCL-F supports a single Intel®Xeon®E3-1200 Series processor or a CoreTM
i3-2100 Series processor in an LGA1155 socket. Please refer to the motherboard
description pages on our web site for a complete listing of supported processors.
Memory
The X9SCL-F has four DIMM sockets that can support up to 32 GB of unbuffered
DDR3-1333/1066 memory. Please refer to Chapter 5 for installing memory.
Serial ATA
An on-chip SATA controller is integrated into the X9SCL-F to provide a six-port, 3
Gb/sec Serial ATA subsystem, which is RAID 0, 1, 5 and 10 supported (RAID 5
supported with Windows OS only). The SATA drives are hot-swappable units. Note:
The operating system you use must have RAID support to enable the hot-swap
capability and RAID function of the SATA drives. Documentation on RAID setup
guidelines can be found on our web site.
I/O Ports
The color-coded I/O ports include one COM port, a VGA(monitor) port, two USB 2.0
ports, PS/2 mouse and keyboard ports and two gigabit Ethernet ports. A dedicated
IPMI LAN port is also included.
Graphics Controller
The X9SCL-F features an integrated ATI video controller based on the Matrox
G200eW graphics chip, which has 16 MB of DDR2 memory.

1-3
Chapter 1: Introduction
1-3 Server Chassis Features
The SC111LT-330CB chassis features four 2.5" hard drive bays and a high-efficiency
power supply. Details on the chassis and on service procedures can be found in
Chapter 6. The following is a general outline of the main features of the chassis.
System Power
The SC111LT-330CB features a single 330W power supply module. The system
must be shut down when replacing or removing this power supply module.
PCI Expansion Slots
A riser card (CSE-RR1U-E8) is included to support one PCI-E 2.0 x8 add-on card.
See page 5-11 for installing add-on cards.
Control Panel
The SC111 control panel provides important system monitoring and control informa-
tion. LEDs indicate power on, network activity, hard disk drive activity and a UID
(Universal Information) LED. Also present are a main power button, a system reset
button and a UID button.
Cooling System
The SC111 chassis' revolutionary cooling design has been optimized to provide
sufficient cooling for dual CPU configurations. The chassis includes an air shroud
and three 4-cm counter-rotating fans located in the middle of the chassis. Two
additional 4-cm fans may be added to cool the PCI cards. There is a "Fan Speed
Control Mode" in BIOS that allows chassis fan speed to be determined by system
temperature.

1-4
SUPERSERVER 1017C-TF User's Manual
Figure 1-1. Intel C202 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.

1-5
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone], ext.132 or 139

1-6
SUPERSERVER 1017C-TF User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 1017C-TF up
and running. Following these steps in the order given should enable you to have
the system operational within a minimum amount of time. This quick setup assumes
that server system has come to you with the processors and memory preinstalled.
If your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing specific components.
2-2 Unpacking the System
You should inspect the box the SuperServer 1017C-TF was shipped in and note
if it was damaged in any way. If the server itself shows damage you should file a
damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fields are generated. You will also need
it placed near a grounded power outlet. Read the Rack and Server Precautions in
the next section.
2-3 Preparing for Setup
The box the SuperServer 1017C-TF was shipped in should include two sets of rail
assemblies, two rail mounting brackets and the mounting screws you will need to
install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section in
its entirety before you begin the installation procedure outlined in the sections that
follow.
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front door•
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.This product is for

2-2
SUPERSERVER 1017C-TF User's Manual
!
!
Warnings and Precautions!
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
This product is not suitable for use with visual display work place devices•
acccording to §2 of the the German Ordinance for Work with Visual Display
Units.
Rack Precautions
Ensure that the leveling jacks on the bottom of the rack are fully extended to•
the floor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack. In multiple•
rack installations, the racks should be coupled together.
Always make sure the rack is stable before extending a component from the•
rack.
You should extend only one component at a time - extending two or more si-•
multaneously may cause the rack to become unstable.
Server Precautions
Review the electrical and general safety precautions in Chapter 4.•
Determine the placement of each component in the rack• before you install the
rails.
Install the heaviest server components on the bottom of the rack first, and then•
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from•
power surges, voltage spikes and to keep your system operating in case of a
power failure.
Allow the hot plug drives and power supply modules to cool before touching•
them.
Always keep the rack's front door and all panels and components on the servers•
closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-4
SUPERSERVER 1017C-TF User's Manual
2-4 Installing the System into a Rack
This section provides information on installing the SC111 chassis into a rack unit with
the rails provided. There are a variety of rack units on the market, which may mean
the assembly procedure will differ slightly. You should also refer to the installation
instructions that came with the rack unit you are using.
Note: This rail will fit a rack between 26" and 33.5" deep.
Identifying the Sections of the Rack Rails
The chassis package includes two rack rail assemblies in the rack mounting kit.
Each assembly consists of two sections: an inner rail that secures directly to the
chassis, and an outer rail that secures directly to the rack itself.
Inner Rails
The SC111 chassis includes a set of inner rails which are to be secured to the
chassis, allow the chassis to be mounted into a rack.
Figure 2-1. Inner Rails
Inner Rails

Chapter 2: Server Installation
2-5
SCALE 0.400
Figure 2-2. Installing the Inner Rails
Installing the Inner Rails
Installing the Inner Rails to the Chassis
Place the inner rail on the side of the chassis, aligning the hooks of the chas-1. sis with the rail extension holes. Make sure the rail faces "outward".
Slide the rail toward the front of the chassis.2.
Secure the chassis with two screws as illustrated.3.
Repeat steps 1-3 for the other inner rail.4.
1
1
1
31
31
1
1
2
1
2

2-6
SUPERSERVER 1017C-TF User's Manual
Outer Rail Options
The SC111 chassis supports outer rails which secure the chassis into the rack.
Installing the Outer Rails to the Rack
Installing the Outer Rails to the Rack
Attach the front bracket (A) to outer rail (B). Attach it to the flat side of the1. outer rail (B), on the front end. Secure them together using the screws pro-
vided.
Attach the rear bracket (C) to the flat side of the outer rail (B), on the rear2. end. Secure them together using the screws provided.
Secure the front bracket (A) to the front of the rack using the screws pro-3. vided.
Secure the rear bracket (C), to the rear of the rack using the screws provided.4.
Repeat steps 1-4 for the other outer rail.5.
Secure this end
to the front of the
rack
Secure this
end to the
rear of the
rack
Attach this end
to the front of the
outer rail
Attach this end
to the rear of the
outer rail
Figure 2-3. Assembling the Outer Rails
Outer Rail
Rear
Front
1
A
1
B
1
C