Supero SuperServer 6025B-8 User manual

®
SUPERSERVER 6025B-T
SUPERSERVER 6025B-8
USER’S MANUAL
1.0b
SUPER
NIC 1NIC 2

Manual Revision 1.0b
Release Date: November 12, 2008
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITH THE PRODUCT, INCLUDINGTHE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2008 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6025B-T/6025B-
8. Installation and maintainance should be performed by experienced technicians
only.
The SuperServer 6025B-T/6025B-8 is a high-end server based on the SC823TQ-
550LP/SC823S-550LP 2U rackmount chassis and the X7DBE/X7DB8, a dual pro-
cessor serverboard that supports Intel®XeonTM processors at a Front Side (System)
Bus speed of 1333 MHz and up to 32 GB of FBD ECC DDR2-667/533 SDRAM.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the X7DBE/X7DB8 serverboard
and the SC823TQ-550LP/SC823S-550LP chassis, which comprise the SuperServer
6025B-T/6025B-8.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6025B-
T/6025B-8 into a rack and check out the server configuration prior to powering
up the system. If your server was ordered without processor and memory com-
ponents, this chapter will refer you to the appropriate sections of the manual for
their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

SUPERSERVER 6025B-T/6025B-8 User's Manual
iv
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6025B-T/6025B-8.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X7DBE/X7DB8 serverboard, in-
cluding the locations and functions of connections, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC823TQ-550LP/SC823S-550LP
server chassis. You should follow the procedures given in this chapter when install-
ing, removing or reconfiguring SATAor peripheral drives and when replacing system
power supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS POST Messages
Appendix B: BIOS POST Codes
Appendix C: Software Installation
Appendix D: System Specifications

v
Preface
Notes

vi
Table of Contents
Preface
About This Manual ...................................................................................................... iii
Manual Organization ................................................................................................... iii
Chapter 1: Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
1-3 Server Chassis Features ................................................................................ 1-3
1-4 Contacting Supermicro ................................................................................... 1-6
Chapter 2: Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System ................................................................................... 2-1
2-3 Preparing for Setup ........................................................................................ 2-1
2-4 Installing the System into a Rack ................................................................... 2-4
2-5 Checking the Serverboard Setup ................................................................... 2-8
2-6 Checking the Drive Bay Setup ..................................................................... 2-10
Chapter 3: System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Buttons .................................................................................... 3-1
Reset ........................................................................................................ 3-1
Power ....................................................................................................... 3-1
3-3 Control Panel LEDs ........................................................................................ 3-2
Overheat/Fan Fail .................................................................................... 3-2
NIC1 ......................................................................................................... 3-2
NIC2 ......................................................................................................... 3-2
HDD .......................................................................................................... 3-2
Power ....................................................................................................... 3-3
3-4 SATA/SCSI Drive Carrier LEDs ...................................................................... 3-3
Chapter 4: System Safety
4-1 Electrical Safety Precautions .......................................................................... 4-1
4-2 General Safety Precautions ........................................................................... 4-2
4-3 ESD Safety Precautions ................................................................................. 4-3
4-4 Operating Precautions .................................................................................... 4-4
SUPERSERVER 6025B-T/6025B-8 User's Manual

Chapter 5: Advanced Serverboard Setup
5-1 Handling the Serverboard .............................................................................. 5-1
5-2 Processor and Heatsink Installation ............................................................... 5-2
5-3 Connecting Cables ......................................................................................... 5-5
Connecting Data Cables .......................................................................... 5-5
Connecting Power Cables ....................................................................... 5-5
Connecting the Control Panel .................................................................. 5-6
5-4 I/O Ports ......................................................................................................... 5-7
5-5 Installing Memory ........................................................................................... 5-7
5-6 Adding PCI Cards ........................................................................................... 5-9
5-7 Serverboard Details ........................................................................................ 5-9
X7DBE/X7DB8 Layout ........................................................................... 5-10
X7DBE/X7DB8 Quick Reference ........................................................... 5-11
5-8 Connector Definitions ................................................................................... 5-12
ATX Power Connector ............................................................................ 5-12
Auxiliary Power Connector ..................................................................... 5-12
Processor Power Connector .................................................................. 5-12
NMI Button ............................................................................................. 5-12
Power LED ............................................................................................. 5-12
HDD LED ............................................................................................... 5-13
NIC1 LED ............................................................................................... 5-13
NIC2 LED ............................................................................................... 5-13
Overheat/Fan Fail LED .......................................................................... 5-13
Power Fail LED ...................................................................................... 5-13
Reset Button ......................................................................................... 5-14
Power Button .......................................................................................... 5-14
Universal Serial Bus (USB0/1) ............................................................... 5-14
Chassis Intrusion .................................................................................... 5-14
Serial Ports ............................................................................................. 5-15
Power Fail Header ................................................................................. 5-15
Fan Headers .......................................................................................... 5-15
Extra Universal Serial Bus Headers ...................................................... 5-16
Power LED/Speaker ............................................................................... 5-16
ATX PS/2 Keyboard and Mouse Ports .................................................. 5-16
Overheat LED ........................................................................................ 5-16
Wake-On-LAN ........................................................................................ 5-17
Wake-On-Ring ........................................................................................ 5-17
SMB ........................................................................................................ 5-17
vii
Table of Contents

viii
SMB Power ............................................................................................ 5-17
SGPIO .................................................................................................... 5-18
JLAN1/2 .................................................................................................. 5-18
Alarm Reset ........................................................................................... 5-18
Keylock ................................................................................................... 5-18
5-9 Jumper Settings ............................................................................................ 5-19
Explanation of Jumpers ......................................................................... 5-19
CMOS Clear ........................................................................................... 5-19
VGA Enable/Disable ............................................................................... 5-19
3rd Power Supply Alarm Enable/Disable ............................................... 5-20
Watch Dog Enable/Disable .................................................................... 5-20
Compact Flash Master/Slave ................................................................. 5-20
JLAN Enable/Disable ............................................................................. 5-21
SCSI Controller Enable/Disable ............................................................. 5-21
SCSI Termination Enable/Disable .......................................................... 5-21
5-10 Onboard Indicators ....................................................................................... 5-22
JLAN1/JLAN2 LEDs ............................................................................... 5-22
5-11 Parallel Port, Floppy, IDE, SATA and SCSI Drive Connections ................... 5-23
Parallel Port Connector .......................................................................... 5-23
Floppy Connector ................................................................................... 5-24
IDE Connectors ...................................................................................... 5-25
SATA Ports ............................................................................................. 5-25
Ultra320 SCSI Ports ............................................................................... 5-26
Chapter 6: Advanced Chassis Setup
6-1 Static-Sensitive Devices ................................................................................. 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Fans ................................................................................................... 6-3
System Fan Failure .................................................................................. 6-3
Replacing System Fans ........................................................................... 6-3
6-4 Drive Bay Installation/Removal ....................................................................... 6-4
Accessing the Drive Bays ........................................................................ 6-4
SATA/SCSI Drive Installation ................................................................... 6-5
Installing a Component in the 5.25" Drive Bay ........................................ 6-8
DVD-ROM and Floppy Drive Installation ................................................. 6-8
6-5 Power Supply ................................................................................................. 6-9
Power Supply Failure ............................................................................... 6-9
Removing/Replacing the Power Supply ................................................... 6-9
SUPERSERVER 6025B-T/6025B-8 User's Manual

Table of Contents
ix
Chapter 7: BIOS
7-1 Introduction ..................................................................................................... 7-1
7-2 Running Setup ................................................................................................ 7-2
7-3 Main BIOS Setup ............................................................................................ 7-2
7-4 Advanced Setup ............................................................................................. 7-7
7-5 Security ......................................................................................................... 7-19
7-6 Boot .............................................................................................................. 7-20
7-7 Exit ................................................................................................................ 7-21
Appendices:
Appendix A: BIOS POST Messages
Appendix B: BIOS POST Codes
Appendix C: Software Installation
Appendix D: System Specifications

Notes
x
SUPERSERVER 6025B-T/6025B-8 User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 6025B-T/6025B-8 is a high-end server that is comprised of two
main subsystems: the SC823TQ-550LP/SC823S-550LP 2U server chassis and the
X7DBE/X7DB8 Intel Xeon serverboard. Please refer to our web site for information
on operating systems that have been certified for use with the 6025B-T/6025B-8.
In addition to the serverboard and chassis, various hardware components have been
included with the SuperServer 6025B-T/6025B-8, as listed below:
 Four (4) 8-cm hot-swap chassis fans (FAN-0070)
 One (1) air shroud (CSE-PT43)
One (1) 3.5" floppy drive [FPD-PNSC-02(1)]
One (1) DVD ROM drive [DVM-PNSC-824(B)]
 One (1) 5.25" dummy drive tray
 One (1) front control panel cable (CBL-0049L)
 Serial ATA Accessories (6025B-T)
One (1) backplane (CSE-SAS-822TQ)
Six (6) data cables (CBL-0061L)
Two (2) 8-pin to 8-pin SGPIO ribbon cables (CBL-0157L)
Six (6) SATA hot-swap drive carriers [CSE-PT17(B)]
 SCSI Accessories (6025B-8 only)
Six (6) SCA SCSI hard drive carriers (CSE-PT-17(B))
One (1) SCSI backplane (CSE-SCA-822S)
One (1) Ultra320 SCSI cable (CBL-033L-U320)
 Optional:
Two (2) CPU passive heatsinks (SNK-P0018)
One (1) bundled rackmount kit [CSE-PT025(B)]
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 6025B-T/6025B-8 User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6025B-T/6025B-8 lies the X7DBE/X7DB8, a dual
processor serverboard based on the Intel 5000P chipset and designed to provide
maximum performance. Below are the main features of the X7DBE/X7DB8. (See
Figure 1-1 for a block diagram of the Intel 5000P chipset).
Processors
The X7DBE/X7DB8 supports single or dual Intel dual-core Xeon processors 5000
series at a FSB speed of 1333 MHz. Please refer to the serverboard descrip-
tion pages on our web site for a complete listing of supported processors (www.
supermicro.com).
Memory
The X7DBE/X7DB8 has eight 240-pin DIMM slots that can support up to 32 GB of
ECC FBD (Fully Buffered DIMM) DDR2-667 or DDR2-533 SDRAM. The memory
is an interleaved configuration, which requires modules of the same size and speed
to be installed in pairs.
Serial ATA
A SATA controller is integrated into the South Bridge of the 5000P chipset to
provide a six-port Serial ATA subsystem, which is RAID 0, 1, 10 and 5 supported.
The Serial ATA drives are hot-swappable units.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the Serial ATA drives.
Onboard SCSI (6025B-8 only)
An onboard Adaptec AIC-7902 dual-channel SCSI controller in integrated into the
X7DB8, which supports 80-pin SCAUltra320 SCSI hard drives. (Standard 1" drives
are supported. SCA = Single Connection Attachment.) The SCSI drives are con-
nected to an SCAbackplane that provides power, bus termination and configuration
settings. The SCSI drives are hot-swappable units.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SCSI drives.

1-3
Chapter 1: Introduction
PCI Expansion Slots
The X7DBE/X7DB8 has six PCI expansion slots, which includes two x8 PCI-Express
slots, one x4 PCI-Express slot, two PCI-X 133 MHz slots and one PCI-X 100 MHz
slot. On the X7DB8, the 100 MHz PCI-X slot supports Zero Channel RAID.
Onboard Controllers/Ports
One floppy drive controller and one onboard ATA/100 controller are provided to
support up to two IDE hard drives or ATAPI devices. The color-coded I/O ports
include one COM port (an additional COM header is located on the serverboard), a
VGA (monitor) port, a parallel port, two USB 2.0 ports, PS/2 mouse and keyboard
ports and two gigabit Ethernet ports. Two front side USB ports are also included
on the front of the chassis.
ATI Graphics Controller
The X7DBE features an integratedATI video controller based on the ES1000 graph-
ics chip. The ES1000 was designed specifically for servers, featuring low power
consumption, high reliability and superior longevity.
Other Features
Other onboard features that promote system health include onboard voltage moni-
tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.
1-3 Server Chassis Features
The following is a general outline of the main features of the SC823TQ-550LP/
SC823S-550LP server chassis.
System Power
The SC823TQ-550LP and SC823S-550LPboth feature a single 550W power supply.
The system must be shut down and the AC power cord removed before replacing
or performing any service on the power supply unit.

1-4
SUPERSERVER 6025B-T/6025B-8 User's Manual
Serial ATA Subsystem
The Serial ATA subsystem supports up to six Serial ATA drives. The Serial ATA
drives are hot-swappable units and are connected to a backplane that provides
power and control.
Note: The operating system you use must have RAID support to enable the hot-
swap capability of the Serial ATA drives.
Front Control Panel
The control panel on the SuperServer 6025B-T/6025B-8 provides system monitoring
and control. LEDs indicate system power, HDD activity, network activity, system
overheat and power supply failure. A main power button and a system reset button
are also included.
I/O Backplane
The SC823TQ-550LP/SC823S-550LP is anATX form factor chassis that is designed
to be used in a 2U rackmount configuration. The I/O backplane provides seven
low-profile PCI expansion slots, one COM port, a parallel port, a VGAport, two USB
2.0 ports, PS/2 mouse and keyboard ports and two gigabit Ethernet ports.
Cooling System
The SC823TQ-550LP/SC823S-550LP chassis has an innovative cooling design
that includes four 8-cm hot-plug system cooling fans located in the middle section
of the chassis. An air shroud channels the air flow from these fans to efficiently
cool the processor area of the system. The power supply module(s) also includes
a cooling fan.

1-5
Chapter 1: Introduction
Figure 1-1. Intel 5000P/ESB2 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
ESB2
CPU1
FBD DIMM Bank1
DDR2
1067/1333MT/s
SATA Ports(6)
IDE Ports(2)
USB Ports(5)
S I/O BIOS
Kybd/
Mouse Floppy COM Ports(2)
CPU2
5000P
MCH
Slot 6: PCI-Exp x8/SEPC
Slot 5: PCI-Express x8
LPC
82563
Parallel
Port
ES
1000
FBD DI MM Bank2 FBD DI MM Bank3 FBD DI MM Bank4
FBD CH0
FBD CH1
FBD CH2
FBD CH3
PCI-E x4 PCI-E x8
Slot 4: PCI-Express x8
PXH
Slot 2: PCI-X
Slot 1: PCI-X
Slot 3:PCI-X
LAN Ports (2)
USB2.0
3.0 Gb/s
ATA 100
PCI32
PCI-X133
PCI-Exp
x8
PCI-Exp
x4
Kumeran
PCI-Exp
x8
PCI-Exp
x8
AIC
7902
Note: the AIC-7902 SCSI controller is included with the 6025B-8 (X7DB8 serverboard)
only.

1-6
SUPERSERVER 6025B-T/6025B-8 User's Manual
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone], ext.132 or 139

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 6025B-
T/6025B-8 up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your system has come to you with the processors and memory
preinstalled. If your system is not already fully integrated with a serverboard, pro-
cessors, system memory etc., please turn to the chapter or section noted in each
step for details on installing specific components.
2-2 Unpacking the System
You should inspect the box the SuperServer 6025B-T/6025B-8 was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
file a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 6025B-
T/6025B-8. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic fields are generated.
You will also need it placed near a grounded power outlet. Read the Rack and
Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6025B-T/6025B-8 was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.

2-2
SUPERSERVER 6025B-T/6025B-8 User's Manual
Choosing a Setup Location
- Leave enough clearance in front of the rack to enable you to open the front
door completely (~25 inches).
- Leave approximately 30 inches of clearance in the back of the rack to allow
for sufficient airflow and ease in servicing.
-This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
- This product is not suitable for use with visual display work place devices ac-
cording to §2 of the the German Ordinance for Work with Visual Display Units.
Rack Precautions
- Ensure that the leveling jacks on the bottom of the rack are fully extended to the
floor with the full weight of the rack resting on them.
- In single rack installation, stabilizers should be attached to the rack.
- In multiple rack installations, the racks should be coupled together.
- Always make sure the rack is stable before extending a component from the
rack.
- You should extend only one component at a time - extending two or more simul-
taneously may cause the rack to become unstable.
Server Precautions
- Review the electrical and general safety precautions in Chapter 4.
- Determine the placement of each component in the rack before you install the
rails.
- Install the heaviest server components on the bottom of the rack first, and then
work up.
- Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a power
failure.
-Allow the hot plug SATA/SCSI drives and power supply units to cool before touch-
ing them.
- Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
!
!
Warnings and Precautions!

Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-4
SUPERSERVER 6025B-T/6025B-8 User's Manual
2-4 Installing the System into a Rack
This section provides information on installing the SuperServer 6025B-T/6025B-8
into a rack unit. If the 6025B-T/6025B-8 has already been mounted into a rack, you
can skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on the
market, which may mean the assembly procedure will differ slightly. The following
is a guideline for installing the system into a rack with the rack rails provided. You
should also refer to the installation instructions that came with the rack unit you
are using.
Identifying the Sections of the Rack Rails
You should have received two rack rail assemblies with the 6025B-T/6025B-8. Each
of these assemblies consist of two sections: an inner fixed chassis rail that secures
directly to the 6025B-T/6025B-8 (A) and an outer fixed rack rail that secures directly
to the rack itself (B). All screws and hardware mentioned in the installation steps
should be included in the hardware kit.
To remove the fixed chassis rail (A), pull it out as far as possible - you should hear
a "click" sound as a locking tab emerges from inside the rail assembly and locks
the inner rail. Then depress the locking tab to pull the inner rail completely out.
Do this for both the left and right side rack rail assemblies.
Figure 2-1. Identifying the Sections of the Rack Rails
A
B
Locking Tab