Supero SuperServer 6026TT-HDTRF User manual

SUPER
USER’S MANUAL
Revision 1.0b
®
SuperServer 6026TT-HDTRF
SuperServer 6026TT-HDIBXRF
SuperServer 6026TT-HDIBQRF
SuperServer 6026TT-D6RF
SuperServer 6026TT-D6IBXRF
SuperServer 6026TT-D6IBQRF

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITHTHE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro-
ductive harm.
Manual Revision 1.0b
Release Date: May 16, 2011
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2011 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6026TT-HDTRF/
HDIBXRF/HDIBQRF/6026TT-D6RF/D6IBXRF/D6IBQRF. Installation and mainte-
nance should be performed by experienced technicians only.
The SuperServer 6026TT-HD/D6 series server is a 2U Twin (two serverboards/
nodes in a 2U chassis) rackmount server based on the SC827HD-R1400B server
chassis and four Super X8DTT-HF+/X8DTT-HIBXF+/X8DTT-HIBQF+ serverboards.
The "(H)" in the product name indicates that the system is cableless.
The D6 models feature the inclusion of a daughter card with an LSI 2108 SAS 2.0
controller in each node. The main differences between the various serverboards
and the servers they are in is shown in the table below:
Model Variations (Differences between X8DTT-x Models)
X8DTT-HF+ X8DTT-HIBXF+ X8DTT-HIBQF+
IPMI 2.0 w/ KVM
Over LAN Yes Yes Yes
InfiniBand
Connection No Yes Yes
DDR IB No Yes No
QDR IB No No Yes
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the Super X8DTT-HF+/X8DTT-
HIBXF+/X8DTT-HIBQF+ serverboard and the SC827HD-R1400B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6026TT-
HDTRF/HDIBXRF/HDIBQRF into a rack and check out the server configuration
prior to powering up the system. If your server was ordered without the processor
iii
Preface

SUPERSERVER 6026TT-HD/D6 Series User's Manual
iv
and memory components, this chapter will refer you to the appropriate sections of
the manual for their installation.
Chapter 3: System Interface
Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6026TT-HD/D6 series server.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X8DTT-HF+/X8DTT-HIBXF+/X8DTT-
HIBQF+ serverboard, including the locations and functions of connectors, headers
and jumpers. Refer to this chapter when adding or removing processors or main
memory and when reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC827HD-R1400B 2U rackmount
server chassis. You should follow the procedures given in this chapter when install-
ing, removing or reconfiguring SATAor peripheral drives and when replacing system
power supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: Installing Windows
Appendix C: System Specifications

v
Preface
Notes

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
1-2 Serverboard Features..................................................................................... 1-2
Processors ......................................................................................................1-2
Memory ...........................................................................................................1-2
Serial ATA........................................................................................................1-2
SAS................................................................................................................. 1-2
PCI Expansion Slots....................................................................................... 1-3
Ethernet Ports................................................................................................. 1-3
Onboard Controllers/Ports ..............................................................................1-3
Graphics Controller......................................................................................... 1-3
Other Features................................................................................................1-3
InfiniBand ........................................................................................................1-3
1-3 Server Chassis Features ................................................................................1-5
System Power.................................................................................................1-5
SATA Subsystem............................................................................................. 1-5
Control Panel ..................................................................................................1-5
Rear I/O Panel................................................................................................ 1-5
Cooling System...............................................................................................1-5
1-4 2U Twin: System Notes...................................................................................1-6
Nodes..............................................................................................................1-6
System Power................................................................................................. 1-6
Backplane/Drives ............................................................................................1-6
1-5 Contacting Supermicro....................................................................................1-7
Chapter 2 Server Installation
2-1 Overview .........................................................................................................2-1
2-2 Unpacking the System....................................................................................2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions..........................................................................................2-2
Rack Mounting Considerations....................................................................... 2-3
Ambient Operating Temperature................................................................2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ...................................................................................2-3
Circuit Overloading..................................................................................... 2-3
SUPERSERVER 6026TT-HD/D6 Series User's Manual

vii
Table of Contents
Reliable Ground .........................................................................................2-3
Removing the Protective Film.........................................................................2-4
2-4 Rack Mounting Instructions............................................................................. 2-5
Separating the Sections of the Rack Rails.....................................................2-5
Installing the Inner Rail Extensions ................................................................2-6
Outer Rack Rails............................................................................................. 2-7
2-5 Checking the Serverboard Setup.................................................................... 2-9
2-6 Preparing to Power On................................................................................. 2-10
Chapter 3 System Interface
3-1 Overview .........................................................................................................3-1
3-2 Control Panel Buttons..................................................................................... 3-1
Power.............................................................................................................. 3-1
UID.................................................................................................................. 3-1
3-3 Control Panel LEDs ........................................................................................3-2
Overheat/Fan Fail ...........................................................................................3-2
NIC.................................................................................................................. 3-2
3-4 Hard Drive Carrier LEDs.................................................................................3-2
Chapter 4 System Safety
4-1 Electrical Safety Precautions..........................................................................4-1
4-2 General Safety Precautions............................................................................4-2
4-3 ESD Precautions............................................................................................. 4-3
4-4 Operating Precautions ....................................................................................4-4
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard...............................................................................5-1
Precautions .....................................................................................................5-1
5-2 I/O Ports..........................................................................................................5-2
Unpacking .......................................................................................................5-2
5-3 Processor and Heatsink Installation................................................................5-3
Installing LGA1366 Processors....................................................................... 5-3
Installing a CPU Heatsink...............................................................................5-5
5-4 Installing Memory............................................................................................ 5-6
5-5 Adding PCI Cards........................................................................................... 5-8
5-6 Serverboard Details ........................................................................................5-9
Serverboard Quick Reference.......................................................................5-10
5-7 Connector Definitions.....................................................................................5-11
5-8 Jumper Settings............................................................................................ 5-15
5-9 Onboard Indicators........................................................................................5-17
5-10 SATA and SAS Ports.....................................................................................5-18

viii
5-11 Installing Additional Drivers........................................................................... 5-19
5-12 Configuring Supero Doctor III.......................................................................5-20
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions .....................................................................................................6-1
Unpacking .......................................................................................................6-1
6-2 Control Panel ..................................................................................................6-2
6-3 System Fans................................................................................................... 6-2
Fan Configuration............................................................................................6-3
System Fan Failure......................................................................................... 6-3
6-4 Hard Drive Installation/Removal......................................................................6-4
Overview .........................................................................................................6-4
Installing and Removing Hard Drives .............................................................6-4
6-5 Node Installation/Removal..............................................................................6-7
6-6 Installing the Air Shrouds................................................................................ 6-9
Air Shrouds .....................................................................................................6-9
6-7 Power Supply.................................................................................................. 6-9
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Configurations......................................................................7-4
7-4 Security Settings........................................................................................... 7-23
7-5 Boot Configuration ........................................................................................ 7-24
7-6 Exit Options...................................................................................................7-26
7-7 BIOS Recovery .............................................................................................7-26
Appendix A BIOS Error Beep Codes
Appendix B Installing Windows
Appendix C System Specifications
SUPERSERVER 6026TT-HD/D6 Series User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 6026TT-HDTRF/HDIBXRF/HDIBQRF/6026TT-D6RF/D6IBXRF/
D6IBQRF is a "2U Twin" server comprised of the SC827HD-R1400B 2U chassis
and two X8DTT-HF+/X8DTT-HIBXF+/X8DTT-HIBQF+ serverboards. Please refer to
our web site for information on operating systems that have been certified for use
with the server (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components may have
been included with the system, as listed below.
Four passive CPU heatsinks (SNK-P0038PS; two for each node))
•
Four 8-cm cooling fans (FAN-0111L4)•
Two air shrouds (MCP-310-82708-0B)•
SATA Accessories:•
Twelve hard drive carriers (six per node) (MCP-220-00075-0B)
One internal HDD backplane (BPN-SAS-827HD)
Two PCI Express riser cards (RSC-R2UT-2E8R)
•
Two daughter cards with LSI 2108 SAS 2.0 controller (BPN-ADP-SAS2-H6IR,•
D6 server series only, one per node)
Rackmount rails kit (MCP-290-00053-0N)
•
One CD containing drivers and utilities•
SuperServer 6026TT-HD/D6 series User's Manual•
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 6026TT-HD/D6 Series User's Manual
Note: The SuperServer 6026TT-HD/D6 series system is cableless and does not
need or come with SATA/SAS cables.
1-2 Serverboard Features
At the heart of the SuperServer 6026TT are four X8DTT-HF+/X8DTT-HIBXF+/
X8DTT-HIBQF+ dual processor serverboards, which are based on Intel's 5520
(North Bridge) + ICH10R (South Bridge) chipset. Below are the main features of
the serverboards. Note that the features on each board are doubled for the server,
which includes two nodes.
Processors
Each X8DTT-HF+/X8DTT-HIBXF+/X8DTT-HIBQF+ supports two Intel® 5600/5500
Series processors in LGA1366 sockets. Please refer to our web site for a complete
listing of supported processors (www.supermicro.com).
Memory
Each X8DTT-HF+/X8DTT-HIBXF+/X8DTT-HIBQF+ has twelve DIMM sockets that
can support up to 192 GB of registered ECC DDR3-1333/1066/800 SDRAM, or 48
GB of unbuffered non-ECC 1333/1066/800 SDRAM. See Chapter 5 Section 6 for
more details on installing memory into the system.
Serial ATA
The South Bridge (ICH10R) of the chipset includes a Serial ATA controller for six
Gb/s SATA drives. The hot-swappable SATA drives are connected to a backplane
that provides power, bus termination and configuration settings. RAID 0, 1, 10 and
5 are supported. Refer to the support area of our web site for procedures on set-
ting up RAID on your system.
SAS
The D6 series servers (6026TT-D6RF/D6IBXRF/D6IBQRF) include a daughter
card with an LSI 2108 SAS controller in rach node, which supports six SAS 2.0
ports (12 ports for the system). The hot-swappable SAS drives are connected to a
backplane that provides power, bus termination and configuration settings.

Chapter 1: Introduction
1-3
PCI Expansion Slots
Each X8DTT-HF+/X8DTT-HIBXF+/X8DTT-HIBQF+ has included riser cards that
allow it to support two full-sized PCI Express 2.0 x8 expansion cards (in x16 slots),
or four total for the server.
Ethernet Ports
An Intel® network controller is integrated into each of the serverboards to support
two Gigabit LAN ports (100/1000Base-T/1000BaseTX, RJ45 output).
Onboard Controllers/Ports
Onboard I/O backpanel ports on each serverboard include one COM port, a VGA
port, two USB ports, a dedicated IPMI LAN port and two Gigabit LAN (NIC) ports.
An InfiniBand port is also included on the X8DTT-HIBXF+/HIBQF+ serverboards
(the 6026TT-HDIBXRF and 6026TT-HDIBQRF only). Up to four USB 2.0 (Universal
Serial Bus) connections (2 Rear USB Ports and 1 Type A Header w/2 USB con-
nections supported) are on each of the servers. There are four sets of I/O ports
included in the server (one set for each serverboard).
Graphics Controller
The X8DTT-HF+/X8DTT-HIBXF+/X8DTT-HIBQF+ features an integrated Matrox
G200eW graphics chip, which includes 16 MB of DDR2 memory.
Other Features
Other onboard features that promote system health include voltage monitors, auto-
switching voltage regulators, chassis and CPU overheat sensors, virus protection
and BIOS rescue.
InfiniBand
The 6026TT-HDIBXRF, 6026TT-D6IBXRF, 6026TT-HDIBQRF and 6026TT-
D6IBQRF include an InfiniBand port at DDR (dual data rate) and QDR (quad
data rate) speeds, respectively. InfiniBand is a scalable serial communications
link intended for connecting processors with high-speed peripherals. (InfiniBand
requires a QSFP connector.)

1-4
SUPERSERVER 6026TT-HD/D6 Series User's Manual
Figure 1-1. Intel 5520 Chipset:
System Block Diagram
Note1: This is a general block diagram. Please see Chapter 5 for details.
Note2: The Intel 5500 (IOH-24D) chipset is available for OEM only.
PROCESSOR#0
#1
#1
#1
#2
DDR3 DIMM
#2
#2
DDR3 DIMM
#1
#1
#1
DDR3 DIMM
#2
#2
#2
DDR3 DIMM
C
C
A
A
B
B
DD
E
E
FF
IOH
5520/5500
36-D/24-D
ICH10R
Intel
82574
BMC/VGA
VGA CONN
DDR II
PCI 4 SATA
LPC
SPI
AT25
DF321
MT25408
Connect-X IB
PCI-E Gen2/DDR or QDR
(For 36D Only)
QSFP
RTL8201N PHY
Dedicated LAN
LPCIO W83527
RMII
PCI-E
x16 Slot
Hotswap Connector
Intel
82574
PROCESSOR#1
RJ-45
RJ-45
QPI

Chapter 1: Introduction
1-5
1-3 Server Chassis Features
The following is a general outline of the main features of the SC827HD-R1400B 2U
chassis. Details on the chassis can be found in Chapter 6.
System Power
When configured as a SuperServer 6026TT-HD/D6 series server, the SC827HD-
R1400B includes a redundant (dual) 1400W power supply, which provides power
to all four serverboards (nodes). If either power supply failes, the other will allow
the system to continue to run.
SATA Subsystem
The SC827HD-R1400B chassis was designed to support twelve SATA hard
drives, which are hot-swappable units. There are six hard drives per node in the
system.
Control Panel
The SC827HD-R1400B features two independant control panels associated with
each serverboard (node) in the chassis. Each control panel has LEDs to indicate
power on, network activity, power fail, fan fail, system overheat conditions and the
UID LED. Each control panel also includes a main power button and a UID but-
ton.
Rear I/O Panel
The SC827HD-R1400B is a 2U rackmount chassis. The rear of the chassis provides
slots for four full-height, full-length PCI Express x8 expansion cards (in x16 slots),
two COM ports, four USB ports, two VGA ports and four Gb Ethernet ports. See
Chapter 6 for details.
Cooling System
The SC827HD-R1400B chassis has an innovative cooling design that features four
8-cm high-performance fans. A fan speed control setting in BIOS allows fan speed
to be determined by system temperature. See Chapter 6 for details.

1-6
SUPERSERVER 6026TT-HD/D6 Series User's Manual
1-4 2U Twin: System Notes
As a 2U Twin configuration, the 6026TT-HD/D6 series is a unique server system.
With two system boards incorporated into a single chassis acting as two separate
nodes, there are several points you should keep in mind.
Nodes
Each of the two serverboards act as a separate node in the system.As independant
nodes, each may be powered off and on without affecting the others. In addition,
each node is a hot-swappable unit that may be removed from the rear of the chassis.
The nodes are connected to the server backplane by means of an adapter card.
System Power
The server has an additional 1400W power supply module (two total) for power
redundancy. If a power supply module fails the other backup module will keep the
system running until it can be replaced.
Backplane/Drives
As a system, the 6026TT-HDx and 6026TT-D6x servers supports the use of twelve
SATAand SAS drives, respectively.Asingle backplane works to apply system-based
control for power and fan speed functions, yet at the same time logically connects
a set of six SATA drives to each serverboard. Consequently, RAID setup is limited
to a six-drive scheme (RAID cannot be spread across all twelve drives). See the
Drive Bay Installation/Removal section in Chapter 6 for the logical hard drive and
node configuration.

Chapter 1: Introduction
1-7
1-5 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone], ext.132 or 139

1-8
SUPERSERVER 6026TT-HD/D6 Series User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get the system up and running.
Following these steps in the order given should enable you to have the system
operational within a minimum amount of time. This quick setup assumes that your
system has come to you with the processors and memory preinstalled. If your sys-
tem is not already fully integrated with a serverboard, processors, system memory
etc., please turn to the chapter or section noted in each step for details on installing
specific components.
2-2 Unpacking the System
You should inspect the box the system was shipped in and note if it was damaged
in any way. If the server itself shows damage you should file a damage claim with
the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should be
situated in a clean, dust-free area that is well ventilated. Avoid areas where heat,
electrical noise and electromagnetic fields are generated. You will also need it placed
near a grounded power outlet. Be sure to read the Rack and Server Precautions
in the next section.
2-3 Preparing for Setup
The box the server was shipped in should include the rackmount hardware needed
to install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section in
its entirety before you begin the installation procedure outlined in the sections that
follow.

2-2
SUPERSERVER 6026TT-HD/D6 Series User's Manual
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front•
door completely (~25 inches).
Leave approximately 30 inches of clearance in the back of the rack to allow for
•
sufficient airflow and ease in servicing.
This product is for installation only in a Restricted Access Location (dedicated
•
equipment rooms, service closets and the like).
This product is not suitable for use with visual display work place devices accord-
•
ing to §2 of the the German Ordinance for Work with Visual Display Units.
!
!
Warnings and Precautions!
Rack Precautions
Ensure that the leveling jacks on the bottom of the rack are fully extended to•
the floor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack.
•
In multiple rack installations, the racks should be coupled together.•
Always make sure the rack is stable before extending a component from it.•
You should extend only one component at a time - extending two or more si-•
multaneously may cause the rack to become unstable.
Server Precautions
Review the electrical and general safety precautions in Chapter 4.•
Determine the placement of each component in the rack• before you install the
rails.
Install the heaviest server components on the bottom of the rack first, and then
•
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
•
power surges, voltage spikes and to keep your system operating in case of a
power failure.

Chapter 2: Server Installation
2-3
Allow the hot plug SATA/SAS drives and power supply modules to cool before•
touching them.
Always keep the rack's front door and all panels and components on the servers
•
closed when not servicing to maintain proper cooling.
Make sure all power and data cables are properly connected and not blocking
•
the chassis airflow. See Chapter 5 for details on cable connections.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-4
SUPERSERVER 6026TT-HD/D6 Series User's Manual
!
Warning: Except for short periods of time, do NOT operate the server
without the cover in place. The chassis cover must be in place to
allow proper airflow and prevent overheating.
Removing the Protective Film
Before operating the server for the first time, it is important to remove the protec-
tive film covering the top of the chassis, in order to allow for proper ventilation and
cooling.
Removing the Protective Film
Peel off the protective film covering the top cover and the top of the chassis1.
Check that all ventilation openings on the top cover and the top of the chassis2. are clear and unobstructed.
Figure 2-1: Removing the Protective Film
Check Ventilation
Openings
1
1
1
2