Supero SUPERSERVER 6026T-3RF User manual

®
SUPERSERVER 6026T-3RF
SUPER
USER’S MANUAL
1.0a

Manual Revision 1.0a
Release Date: January 29, 2010
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITH THE PRODUCT, INCLUDINGTHE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2010 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It pro-
vides information for the installation and use of the SuperServer 6026T-3RF. Instal-
lation and maintainance should be performed by experienced technicians only.
The SuperServer 6026T-3RF is a high-end server based on the SC825TS-R720LPB
2U rackmount chassis and the X8DT3-F dual processor serverboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the X8DT3-F serverboard and
the SC825TS-R720LPB chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6026T-3RF
into a rack and check out the server configuration prior to powering up the system.
If your server was ordered without processor and memory components, this chapter
will refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6026T-3RF.

SUPERSERVER 6026T-3RF User's Manual
iv
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X8DT3-F serverboard, including the
locations and functions of connections, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconfiguring the
serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC825TS-R720LPB server chas-
sis. You should follow the procedures given in this chapter when installing, removing
or reconfiguring SAS/SATA or peripheral drives and when replacing system power
supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications

Notes
Preface
v

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
1-2 Serverboard Features..................................................................................... 1-2
Processors ......................................................................................................1-2
Memory ...........................................................................................................1-2
Onboard SAS..................................................................................................1-2
Serial ATA ....................................................................................................... 1-2
PCI Expansion Slots....................................................................................... 1-3
Onboard Controllers/Ports .............................................................................. 1-3
Graphics Controller......................................................................................... 1-3
Other Features................................................................................................1-3
1-3 Server Chassis Features ................................................................................ 1-3
System Power.................................................................................................1-3
SAS/SATA Subsystem.....................................................................................1-3
Front Control Panel.........................................................................................1-4
I/O Backplane.................................................................................................. 1-4
Cooling System...............................................................................................1-4
1-4 Contacting Supermicro....................................................................................1-6
Chapter 2 Server Installation
2-1 Overview .........................................................................................................2-1
2-2 Unpacking the System.................................................................................... 2-1
2-3 Preparing for Setup.........................................................................................2-1
Choosing a Setup Location............................................................................. 2-1
Rack Precautions............................................................................................2-2
Server Precautions..........................................................................................2-2
Rack Mounting Considerations.......................................................................2-3
Ambient Operating Temperature................................................................ 2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading.....................................................................................2-3
Reliable Ground ......................................................................................... 2-3
2-4 Installing the System into a Rack ...................................................................2-4
Separating the Sections of the Rack Rails.....................................................2-4
Installing the Inner Rail Extension..................................................................2-4
Outer Rack Rails.............................................................................................2-6
2-5 Checking the Serverboard Setup.................................................................... 2-8
SUPERSERVER 6026T-3RF User's Manual

vii
2-6 Checking the Drive Bay Setup...................................................................... 2-10
Chapter 3 System Interface
3-1 Overview .........................................................................................................3-1
3-2 Control Panel Buttons..................................................................................... 3-1
Reset...............................................................................................................3-1
Power..............................................................................................................3-1
3-3 Control Panel LEDs ........................................................................................3-2
Power Fail.......................................................................................................3-2
Overheat/Fan Fail: .......................................................................................... 3-2
NIC1................................................................................................................3-2
NIC2................................................................................................................3-2
HDD................................................................................................................. 3-3
Power..............................................................................................................3-3
3-4 Drive Carrier LEDs..........................................................................................3-3
Chapter 4 System Safety
4-1 Electrical Safety Precautions..........................................................................4-1
4-2 General Safety Precautions............................................................................ 4-2
4-3 ESD Precautions.............................................................................................4-3
4-4 Operating Precautions .................................................................................... 4-4
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard............................................................................... 5-1
Precautions .....................................................................................................5-1
Unpacking .......................................................................................................5-2
5-2 Serverboard Installation.................................................................................. 5-2
5-3 Connecting Cables..........................................................................................5-3
Connecting Data Cables................................................................................. 5-3
Connecting Power Cables .............................................................................. 5-3
Connecting the Control Panel......................................................................... 5-3
5-4 I/O Ports..........................................................................................................5-4
5-5 Installing the Processor and Heatsink ............................................................5-5
Installing an LGA1366 Processor ...................................................................5-5
Installing an Active Heatsink...........................................................................5-7
Removing the Heatsink................................................................................... 5-8
Removing an Active Heatsink.................................................................... 5-8
Memory Support..............................................................................................5-9
DIMM Installation ............................................................................................ 5-9
Memory Support.......................................................................................5-10
5-7 Adding PCI Add-On Cards.............................................................................5-11
Table of Contents

viii
5-8 Serverboard Details ...................................................................................... 5-12
X8DT3-F Quick Reference............................................................................ 5-13
5-9 Connector Definitions ...................................................................................5-14
5-10 Jumper Settings............................................................................................ 5-20
5-11 Onboard Indicators........................................................................................5-23
5-12 Floppy, SAS and SATA Ports........................................................................ 5-24
5-13 Installing Software.........................................................................................5-26
Supero Doctor III...........................................................................................5-27
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions .....................................................................................................6-1
Unpacking .......................................................................................................6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Fans................................................................................................... 6-3
System Fan Failure......................................................................................... 6-3
Replacing System Fans.................................................................................. 6-3
6-4 Drive Bay Installation/Removal....................................................................... 6-4
Accessing the Drive Bays............................................................................... 6-4
SAS/SATA Drive Installation............................................................................ 6-5
Hard Drive Backplane..................................................................................... 6-6
DVD-ROM Installation..................................................................................... 6-7
6-5 Power Supply..................................................................................................6-8
Power Supply Failure...................................................................................... 6-8
Removing/Replacing the Power Supply.......................................................... 6-8
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility..............................................................................7-1
How To Change the Configuration Data......................................................... 7-1
Starting the Setup Utility................................................................................. 7-2
7-2 Main Setup......................................................................................................7-2
7-3 Advanced Setup Configurations......................................................................7-4
7-4 Security Settings........................................................................................... 7-23
7-5 Boot Configuration ........................................................................................ 7-24
7-6 Exit Options...................................................................................................7-26
Appendix A BIOS Error Beep Codes
Appendix B System Specifications
SUPERSERVER 6026T-3RF User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 6026T-3RF is a high-end server comprised of two main subsys-
tems: the SC825TQ-R720LPB 2U server chassis and the X8DT3-F dual processor
serverboard. Please refer to our web site for information on operating systems that
have been certified for use with the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 6026T-3RF, as listed below:
Two passive CPU heatsinks (SNK-P0038P)
•
One slim DVD-ROM drive (DVM-TEAC-DVD-SBT)•
One SATA to USB adapter for DVD-ROM drive (CDM-USATA-G)•
One internal USB cable for DVD-ROM drive (CBL-0341L)•
One black USB/COM port tray (MCP-220-00007-01)•
Three 8-cm chassis fans (FAN-0094L4)•
One air shroud (MCP-310-28001-0N)•
SAS/SATA Accessories•
One SAS/SATA backplane (BPN-SAS-825TQ)
One 2-ft. SATA cable (CBL-0044L)
Two iPass to SATA cables (CBL-0176L-01)
Eight drive carriers (MCP-220-00001-01)
One rackmount kit (MCP-290-00053-0N)
•
One CD containing drivers and utilities•
SuperServer 6026T-3RF User's Manual•
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 6026T-3RF User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6026T-3RF lies the X8DT3-F, a dual processor
serverboard based on the Intel IOH-36D + ICH10R chipset and designed to provide
maximum performance. Below are the main features of the X8DT3-F. (See Figure
1-1 for a block diagram of the chipset).
Processors
The X8DT3-F supports single or dual Intel® Xeon 5500 Series processors (with a
maximum TDP<100W) and future Intel Nehalem processor families (next generation
Intel Xeon® processor). Please refer to the serverboard description pages on our
web site for a complete listing of supported processors (www.supermicro.com).
Memory
The X8DT3-F has twelve 240-pin DIMM slots that can support up to 96 GB of
DDR3-1333/1066/800 registered ECC SDRAM or 24 GB of DDR3-1333/1066/800
unbuffered ECC SDRAM. The memory operates in an interleaved configuration
and requires requires modules of the same size and speed to be installed two at a
time. See Chapter 5 for details.
Onboard SAS
An onboard LSI 1068E SAS controller in integrated into the X8DT3-F for an 8-port
SAS subsystem. The hot-swap SAS drives are connected to a backplane that pro-
vides power, bus termination and configuration settings.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SAS drives. RAID 0, 1, 5 and 10 are sup-
ported. Refer to the following ftp site for setup guidelines <ftp://ftp.supermicro.com/
driver/SAS/LSI/LSI_SAS_EmbMRAID_SWUG.pdf> and Supermicro's web site for
additional inmformation < http://www.supermicro.com/support/manuals/>.
Serial ATA
A Serial ATA controller is integrated into the ICH10R (South Bridge) portion of the
IOH-36D chipset to provide a six-port 3 Gb/s SATA subsystem, which is RAID 0, 1,
10 and 5 supported. The SATA drives are hot-swappable units.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SATA drives. RAID 5 requires the use
of an iButton.

1-3
Chapter 1: Introduction
PCI Expansion Slots
The X8DT3-F has three PCI Express 2.0 x8 slots, one PCI Express x4 slot and
two 32-bit PCI slots.
Onboard Controllers/Ports
A floppy drive connector is included on the serverboard as well as two onboard
ATA/100 connectors, which support IDE hard drives or ATAPI devices. The color-
coded I/O ports include one COM port (an additional COM header is located on
the serverboard), a VGA (monitor) port, two USB 2.0 ports (additional USB headers
are included on the serverboard), PS/2 mouse and keyboard ports and two gigabit
Ethernet ports.
Graphics Controller
The X8DT3-F features an integrated Matrox G200 video controller. The G200 is a
2D/3D/video accelerator chip with a 128-bit core.
Other Features
Other onboard features that promote system health include onboard voltage moni-
tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.
1-3 Server Chassis Features
The following is a general outline of the main features of the SC825TQ-R720LPB
server chassis.
System Power
The SC825TQ-R720LPB features a redundant 720W power supply composed of
two separate power modules. This power redundancy feature allows you to replace
a failed power supply without shutting down the system.
SAS/SATA Subsystem
The SC825TQ-R720LPB supports up to eight SAS or 3Gb/s SATA drives. These
drives are hot-swappable units and are connected to a backplane that provides
power and control.
Note: The operating system you use must have RAID support to enable the hot-
swap capability of the SAS/SATA drives.

1-4
SUPERSERVER 6026T-3RF User's Manual
Front Control Panel
The control panel on the SuperServer 6026T-3RF provides you with system monitor-
ing and control. LEDs indicate system power, HDD activity, network activity, system
overheat and power supply failure. A main power button and a system reset button
are also included. In addition, two USB ports have been incorporated into the control
panel to provide front side USB access.
I/O Backplane
The SC825TQ-R720LPB is an ATX form factor chassis designed to be used in a
2U rackmount configuration. The I/O backplane provides six low-profile add-on card
slots, one COM port, a parallel port, a VGA port, two USB 2.0 ports, PS/2 mouse
and keyboard ports and two gigabit Ethernet ports.
Cooling System
The SC825TQ-R720LPB chassis has an innovative cooling design that includes
three 8-cm hot-plug system cooling fans located in the middle section of the chassis.
An air shroud channels the airflow from the system fans to efficiently cool the proces-
sor area of the system. The power supply module also includes a cooling fan.

1-5
Chapter 1: Introduction
Figure 1-1. Intel IOH-36D/ICH10R Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
PCI-33
PCI-E x8
LANE6
COM2
PCI-E x8
USB 2.0
3.0 Gb/S
Ports
Ports
#0
CPU #2
Intel ICH10R
PCI-E x8
DMI
LANE5
LANE 1/2/3/4
SPI
PCI-E x4
LPC
SIO
W83627
PCI 33MHz
#7-10
CPU #1
QPI
HG
USB
PCIE x4
SATA
#1-2
#6
#5
Intel
IOH-36D
VRD VRD #0-4
#0-3
#0-2
#0-1
DDR3
#1-4
#1-3
#1-2
#1-1
800/1066/1333
800/1066/1333
DDR3
ESI
#1-5
#1-6
#0-5
#0-6
QPI
QPI
#3
TPM
PCI-33
#1
KB
MS COM1
PCI-E x16/8
#4
x16 Slot
#3-4
PCI-E x4
LAN#1
PCI-E x16
PCI-E x8
Ports#4~7
SAS
LSI 1068
B3
Ports#0~3
LAN#2
82576EB
PCI-E x4
#2
PCI-E x8
#5-6
SPEC
BMC WPCM450
#7
Port
Port
#8
(Optional)
6 PHASE 6 PHASE
Option Ports
Ports Port
82576EB

1-6
SUPERSERVER 6026T-3RF User's Manual
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone], ext.132 or 139

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 6026T-3RF
up and running. Following these steps in the order given should enable you to have
the system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing specific components.
2-2 Unpacking the System
You should inspect the box the SuperServer 6026T-3RF was shipped in and note
if it was damaged in any way. If the server itself shows damage you should file a
damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 6026T-
3RF. It should be situated in a clean, dust-free area that is well ventilated. Avoid
areas where heat, electrical noise and electromagnetic fields are generated. You
will also need it placed near a grounded power outlet. Read the Rack and Server
Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6026T-3RF was shipped in should include two sets of
rail assemblies, two rail mounting brackets and the mounting screws you will need
to install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section in
its entirety before you begin the installation procedure outlined in the sections that
follow.
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front door•
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.

2-2
SUPERSERVER 6026T-3RF User's Manual
This product is for installation only in a Restricted Access Location (dedicated•
equipment rooms, service closets and the like).
This product is not suitable for use with visual display work place devices
•
acccording to §2 of the the German Ordinance for Work with Visual Display
Units.
!
!
Warnings and Precautions!
Rack Precautions
Ensure that the leveling jacks on the bottom of the rack are fully extended to•
the floor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack. In multiple
•
rack installations, the racks should be coupled together.
Always make sure the rack is stable before extending a component from the
•
rack.
You should extend only one component at a time - extending two or more si-
•
multaneously may cause the rack to become unstable.
Server Precautions
Review the electrical and general safety precautions in Chapter 4.•
Determine the placement of each component in the rack• before you install the
rails.
Install the heaviest server components on the bottom of the rack first, and then
•
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
•
power surges, voltage spikes and to keep your system operating in case of a
power failure.
Allow any hot plug drives and power supply modules to cool before touching
•
them.
Always keep the rack's front door and all panels and components on the servers
•
closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-4
SUPERSERVER 6026T-3RF User's Manual
2-4 Installing the System into a Rack
This section provides information on installing the SC825 chassis into a rack unit
with the quick-release rails provided. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. You should also refer to
the installation instructions that came with the rack unit you are using.
Note: This rail will fit a rack between 26" and 33.5" deep.
Separating the Sections of the Rack Rails
The chassis package includes two rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fixed chassis rail that secures directly
to the server chassis and an outer fixed rack rail that secures directly to the rack
itself.
Installing the Inner Rail Extension
The SC825 chassis includes a set of inner rails in two sections: inner rails and inner
rail extensions. The inner rails are pre-attached to the chassis, and do not interfere
with normal use of the chassis if you decide not to use a server rack. The inner rail
extension is attached to the inner rail to mount the chassis in the rack.
Installing the Inner Rails
Place the inner rail extensions on the side of the chassis aligning the hooks1. of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.
Slide the extension toward the front of the chassis.2.
Secure the chassis with 2 screws as illustrated. Repeat steps for the other3. inner rail extension.

Chapter 2: Server Installation
2-5
Figure 2-1. Separating the Rack Rails
1
1
1
2
1
4
1
3
Separating the Inner and Outer Rails
Locate the rail assembly in the chassis1. packaging.
Extend the rail assembly by pulling it2. outward.
Press the quick-release tab.3.
Separate the inner rail extension from4. the outer rail assembly.
Rail Assembly
Extending the Rails
Quick-
Release Tab
Separating
the Inner Rail
Extension

2-6
SUPERSERVER 6026T-3RF User's Manual
Outer Rack Rails
Outer rails attach to the rack and hold the chassis in place. The outer rails for the
SC825 chassis extend between 30 inches and 33 inches.
Installing the Outer Rails to the Rack
Secure the back end of the outer rail to the rack, using the screws provided.1.
Press the button where the two outer rails are joined to retract the smaller2. outer rail.
Hang the hooks of the rails onto the rack holes and if desired, use screws to3. secure the front of the outer rail onto the rack.
Repeat steps 1-3 for the remaining outer rail.4.
Figure 2-2. Assembling the Outer Rails
1
1
1
2
1
3