surveillance 112 ACA1574X User manual

HDMI Extender Over Network Cable
User’s manual
IMPORTANT SAFETY INSTRUCTIONS：
1. Do not mix up HDI to RJ45 sender and RJ45 to HDMI receiver before installation .
2. DO not hot plug when it is working.
3. Use DC5V power supply only.Make sure specification matched if using adapters not supplied by factory.
PACKAGE CONTENTS
1.HDMI to RJ45 sender TX*1pcs 2.RJ45 to HDMI receiver RX*1pcs
3.DC5V/1A *2pcs 4. User manual*1pcs
5. IR blaster extension cable *1pcs 6. IR receiver extension cable*1pcs
Installation Requirements
1. HDMI source device(computer graphics card, DVD,PS3, HD monitoring equipment etc).
2. HDMI display device like SDTV, HDTV, projector with HDMI port.
3. UTP/STP cat6/6A/7 cable, follow standard IEEE-568B.
Panel Description
1. HDMI to RJ45 transmitter

1 DC5V power input 2 HDMI signal input
3 IR signal output to connect ith blaster extension cable 4 Reset
5 RJ45 signal output
6 HDMI signal indicator led it lights on all the time with HDMI signal input, flashes with no signal input.
2.RJ45 to HDMI receiver
1reset 2 RJ45 signal input
3 RJ45 indicator led it lights on all the time with HDMI signal transmission, flashes with no signal transmission.
4 DV5V power input 5 HDMI signal output
6 IR signal input to connect with IR receiver extension cable
Installation Procedures
1. Cat6 network cable
FOLLOW THE STANARD OF IEEE-568B:
1- ORANGE/WHITE 2-ORANGE
3- GREEN/WHITE 4- BLUE
5- BLUE/WHITE 6-GREEN
7-BROWN/WHITE 8-BROWN

2. Connections
Connection instruction:
1) Connect TX HDMI input with source device HDMI output.Connect TX HDMI output with HDTV HDMI input.
2) Connect TX CAT6 with RX CAT6.
3) Connect RX HDMI output with HDTV HDMI input.
4) Power on the device and it works.
五、FAQ
Q: No image output or audio and video display is not normal?
A: 1)Adjust RX “RESET” button to reset the device.
2)Try shorter network cable to reconnect.
Q: RX “LINK” led is flashing all the time?
A: 1)Make sure network cable connection follows the standard of IEEE- 568B.
2)Check whether TX has HDMI signal input.
3)Reset TX&RX and reconnect.
Q: RX “LINK” led lights on all the time but no image output?

A: 1)Press RX “RESET” button to reset the device.
2)Make sure HDMI cable is well connected with TV.
3)Make sure the network cable is fine copper wires.
六、Specification
Items
Specifications
Note
HDMI signal
Compatible HDCP
Resolution
supported
480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz,
720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
Network cable
Low resistance and consumption oxygen-free copper
core（CAT6、CAT6A、CAT7）
Transmission
length
CAT6:60m at 1080P
IR remote
control
Support 20~60KHz wide frequency IR remote control
Working
temperature
0℃～60℃
Power Supply
DC5V/1A
2pcs
Power
TX：2W；RX<2W
Size
71.6(W) x 66.6(D) x 24.8(H)mm*2pcs
Weight
170g
Color
Black
Disclaimer
The product name and brand name may be registered trademark of related manufacturers.TM and ® may
be omitted on the user manual. The pictures on the user manual are just for reference,and there may be
some slight difference with the real products.
We reserve the rights to make changes without further notice to a product or system described here in to
improve reliability,function or design.