SwanStone KSEU-3020 User manual

KITCHEN SINK Model No. KSEU-3020
OWNER’S MANUAL
MODEL NO.
KSEU-3020
Installation
Care and
Cleaning
CAUTION:
Read ALL instructions carefully
BEFORE starting your installation.
Save this manual for future reference.
Patent Pending

KITCHEN SINK Model No. KSEU-3020
Step-By-Step Installation Instruction
Model KSEU-3020 20x 39-3/8
(508mm) x (1000mm)
Tools Required
• Ruler
• Drill
• Caulk
• Saber Saw (if counter top cutout is required)
• Screw Driver
TRACE COMPLETELY
AROUND EDGE OF SINK
DRAW A 1-1/2(38mm) RADIUS AT EACH CORNER
5/16 (8mm)
1. If it is necessary to cut out the counter top, invert sink and
position onto the counter top. Locate sink front to rear and right
to left so that the bowl(s) will not interfere with the cabinets
below. Trace a pencil line around the outside edge of the sink
and remove the sink from the counter top.
2. Measure in 5/16(8mm) from the initial sink outline and draw
a second line inside the first. Draw a 1-1/2(38mm) radius at
each corner. This second interior line will be your cutout line.
Check Cutout Line Measurements
Model Width Depth
KSEU-3020 38-3/4(984mm) 19-3/8(492mm)
Measure the cutout line or the pre-cut opening to be sure it
conforms to the sizes listed.

3. Drill starter hole inside of cutout line. 4. Using a saber saw, cut inside of cutout line. Trial fit sink to
check proper fit.
5. Fixture hole locations are identified with a gray label indicating
the most desired placement. Drill starter hole from reverse side.
Working from the top side as illustrated, position a hole saw on
the starter hole and drill to complete the fixture hole. Clean out
fixture hole with a knife or file. (See Caution). Attach faucet,
drain, and accessories according to manufacturer’s instructions.
CAUTION
Use of a hole saw is preferred, however, if punch is used, insure
that ledge is supported and punch is placed directly in middle of
knock-out area. If hole is not used, peel off the label.
6. Attach sink clips as illustrated to underside of sink. Sink clips
provided will accommodate a counter top up to 1-1/2(38mm)
thick.
IMPORTANT
The Euro Style sink design allows for
the drainboard to be located on either
the left or right side. After you decide
on the location of the drainboard, the
fixture holes can then be located.
DRILL STARTER HOLE
INSIDE OF CUTOUT
LINE
CUT INSIDE OF LINE
NOTE
Drill Starter Hole From Bottom
Finish Drilling Hole From Top
Installation • Care and Cleaning

Patent Pending
Form #400-1-94-10M
KITCHEN SINK Model No. KSEU-3020
APPLY
CAULK
Installation • Care and Cleaning
7. Apply a bead of caulk (not included) to the underside of the
sink flange and position sink into counter top opening. First,
tighten screws in front, then tighten rear screws.
8. Connect all faucet supply lines, disposal (if available), and
drain trap fittings per manufacturer instructions.
CHECK FOR LEAKS:
• Supply user tubes to faucet
• Supply riser tubes to shut off valves or lower connections
• Fill sink with water and check for leaks around drain
• Release water from sink and check for possible leaks
• Tighten as needed
CLEANING
Clean your Swanstone kitchen sink as you would any other fine
bath fixture, using normal household detergents and cleansers.
Just wiping the wall surfaces quickly removes watermarks and
residue. Occasional scrubbing with household abrasive cleansers
ensures that the original luster is maintained, similar to tile and
other permanent type bath fixture materials.
REPAIRING
Solid Colors
Use 400 grit sandpaper to remove scratches and gouges in the
surface. A “scotchbright pad” can be used to blend in the area.
Aggregate Colors
Use 400 grit sandpaper to remove scratches and gouges in the
surface. To blend in the area use a fine grade, white, automotive
polishing compound or paste wax.