SwedHeat Lumi 1 User manual

Assembly instructions
List of items needed:
Bubble level
Drill
Rubber hammer
Measuring tape
Hammer

B
A
CD
3,51 m2
E

Name Width Height Length Quantity 3D Front Axonometry
Side
view
A1 34 135 1326 14
A2 34 135 1326 1
A3 34 135 1326 1
B1 34 135 1926 14
B2 34 135 1926 1
B3 34 135 1926 1
C1 34 135 1926 15
C2 34 135 1926 1
D1 34 135 1326 1
D2 34 135 859 14
D3 34 135 1326 1
E1 34 119 704 1
E2 34 135 704 1
Heater
cover
615 500 - 2
Heater
cover
455 500 - 1
Sauna bed 500 90 1400 1
Sauna bed 500 90 1900 2
Bed holder 30 30 500 2
Bed holder 30 30 800 2
Column 40 70 500 3
Roof
panels
950 50 1900 2
Heater protection parts
Sauna beds
Roof of sauna
Column for sauna bed support
Teatree Sauna
Front wall
Back wall
Left wall
Right wall
Entrance wall
Bed holders

Panel
holder
30 30 810 1
Panel
holder
30 30 1356 1
Panel
holder
30 30 1386 1
Panel
holder
30 30 1880 1
Panel
holder
30 30 1910 1
Corners 34 34 2160 3
Covers 75 19 2085 6
Cover 90 19 895 1
Cover 90 19 1400 2
Cover 90 19 1980 1
Cover 90 19 2000 1
Spec. part 21 80 2085 2
Spec. part 26 92 2085 2
Frame
bracket
34 44 1881 1
Frame
bracket
34 44 2160 2
Frame
bracket
34 70 1881 1
Wire cover 140 34 1820 1
Frame
bracket
34 70 2160 2
Sauna door 690 1912 - 1
Sauna
window
361 1890 - 1
Box of
screws
- - - 1
Sealing
tape
- - - 1
Other accessories for sauna building
Roof panel holders
Cover for heater wires
Door frame
Door corner cover
Doors and windows
Sauna Corners
Corner covers
Brackets for doors and windows
Crown for roof covering

Introduction of sauna parts
1
Left wall
Front wall
Right wall
Entrance wall
Heater protection
Corner
Back wall
Roof panel
Door frame
Window frame
Roof panel holders
Bed holders
Sauna covers
Corner covers
Sauna beds

>10cm
>10cm
!
Pay attention to
the position of
the part
Pre-drill holes
for screws
Keep distance
from walls
!
Drive the screw in pre-
drilled holes
5x80mm for
fastening corners to
walls
2
90°
90°
90°

Pre-drill holes
for screws
Use rubber hammer
for wall parts
Make sure to level for
better building accuracy
Drive the screw in pre-
drilled holes
5x80mm for fastening
corners to walls
3

2160 mm
2160 mm
Make sure that the height of the sauna is 2160 mm
Drive the screw in pre-
drilled holes
5x80mmmm for fastening
corners to walls
4
Pre-drill holes
for screws
Use rubber hammer
for wall parts
Make sure to level for
better building accuracy

1. Install the door and window frame brackets in the
locations indicated on the original plan.
2. Pre-drill holes for screws
3. Drive the screw in pre-drilled hole
Drive the screw in pre-drilled
holes on the frame brackets
5x100mm for door/window frame
brackets
5
Pre-drill holes
for screws
Make sure to level for
better building accuracy

1. Install the door frame brackets (which is cut 45°)
in the opening where door frame bracket is.
2. Pre-drill holes for screws
3. Drive the screw in pre-drilled hole
4. Don't forget to place entrance wall bottom part.
Drive the screw in pre-drilled
holes on the frame brackets
5x100mm for 45 degree door frame
brackets
6
Pre-drill holes
for screws
Make sure to level for
better building accuracy

Insert the hinges into the
door glass
1. Insert the hinges into the door glass.
2. After that put the door glass in the door frame that is factory
assembled
7

x
y
x
y
x=x
y=y
! Make sure the glass is centered between the door frame
Mark places for drilling
Drill the marked points
for the hinges
Screw hinges to door
frame
3x35mm for
fastening hinges
8

1. Put the glass in the frame brackets
2. Center the glass
3. Nail the window surrounds to the frame
9
Nail the window
surrounds to the frame
2x30mm glass covers

Pre-drill holes
for screws
Drive the screw in pre-
drilled hole
Place the door and window in
between the frame you attached
earlier
5x100mm for fastening door
frame
10

Pre-drill holes
for screws
Drive the screw in pre-
drilled hole
3x35mm for fastening door and
window frame covers
11