Sweetpea Baby ROSE 3 DRAWER CHEST User manual

Read all instructions before
assembling and using product.
IMPORTANT - Keep instructions for
future use. 0222R1-780
Owner’s Manual
ROSE 3 DRAWER CHEST
Scan the QR code to register your product
https://www.sweetpeababy.com/customer-care/product-registration/

Contact Sweetpea
Baby in case of any
assistance needed.
2www.sweetpeababy.com/help
SAFETY TIPS
Adult Assembly
Required.
DO NOT use the
product if it is
damaged, broken,
and/or components are
missing or broken.
To protect your parts
during assembly,
please place them on a
soft surface.
Small parts may
present choking
hazard prior to
assembly.
Please read the
instructions
thoroughly. Identify all
parts & hardware.
Improper or unsafe use
of power drills/drivers
can result in death or
serious injury.
To clean surface, use
only water on a damp
cloth. Do not use
window cleaner or
cleaning abrasive as it
will scratch the surface
and could damage the
protective coating.
0-6
Always monitor your
child’s activity in the
nursery or near
furniture.

…. for choosing Sweetpea Baby and congratulations on joining our family;
a family that has been transforming lives for over 30 years!
We appreciate your feedback and wish you the very best in the
coming years with your new addition. If you have any questions
or concerns please don’t hesitate to reach out to us. One of our
trusted Customer Care representatives will be happy to assist you.
Thank you again for entrusting us to provide you with safe
and affordable baby products and accessories.
THANK YOU...
LIMITED WARRANTY:
• Sweetpea Baby warrants its product to be free from defects in material
and workmanship and agrees to remedy any such defect.
• This warranty covers 1 year from the date of original purchase.
• This warranty is valid only upon presentation of proof of purchase.
• This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
• This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
• This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
www.sweetpeababy.com/help
3

WARNINGS
www.sweetpeababy.com/help
4
• FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
• CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS
OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE.
• DO NOT USE THIS DRESSER IF ANY PARTS ARE MISSING, DAMAGED OR BROKEN.
CONTACT SWEETPEA BABY - 1532 S. WASHINGTON AVE, PISCATAWAY, NJ 08854
FOR REPLACEMENT PARTS.
• IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
• SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM FURNITURE TIP-OVER.
TO HELP PREVENT THIS, PLACE THE HEAVIEST ITEMS ON THE LOWER SHELVES AND
DRAWERS. DO NOT SET HEAVY OBJECTS ON TOP SHELVES AND DRAWERS.
• NEVER OPEN MORE THAN ONE DRAWER AT A TIME.
• THE USE OF TIP-OVER RESTRAINTS MAY REDUCE BUT NOT ELIMINATE THE RISK OF
TIP-OVER.
• DO NOT SET TVs OR OTHER HEAVY OBJECTS ON TOP OF THIS PRODUCT.
• ALWAYS MONITOR YOUR CHILD’S ACTIVITY WHEN IN THE NURSERY.
• NEVER ALLOW CHILDREN TO CLIMB OR HANG ON DRAWERS, SHELVES, AND DOORS.
• DO NOT ALLOW CHILDREN STANDING IN DRAWERS.
• DO NOT ALLOW CHILDREN STANDING ON TOP OF THIS PRODUCT.
• TO AVOID HEAD INJURY, DO NOT ALLOW CHILDREN TO PLAY UNDERNEATH OPEN
DRAWERS.
• DO NOT LEAVE DRAWERS OPEN WHEN IN USE.
• ACCESSORY ITEMS MUST BE SECURELY FASTENED TO THIS PRODUCT ACCORDING
TO THE INSTRUCTIONS PROVIDED WITH THOSE ITEMS.
CHILDREN HAVE DIED FROM FURNITURE TIPOVER, TO REDUCE THE RISK OF
TIPOVER :
• ALWAYS INSTALL TIPOVER RESTRAINT PROVIDED.
• NEVER PUT A TV ON THIS PRODUCT.
• NEVER ALLOW CHILDREN TO STAND, CLIMB OR HANG ON DRAWERS, DOORS OR
SHELVES.
• NEVER OPEN MORE THAN ONE DRAWER AT A TIME.
• PLACE HEAVIEST ITEMS IN THE LOWER DRAWERS.

www.sweetpeababy.com/help
5
Bottom Rear Panel
8
PARTS
If there are any missing parts, please contact Sweetpea Baby before using the
product.
Top Panel
1Left Side Panel 2Right Side Panel 3
4Top Front Rail Center Front Rail (x2) 5Bottom Front Rail 6
Top Rear Panel
7

www.sweetpeababy.com/help
6
PARTS (Cont.)
If there are any missing parts, please contact Sweetpea Baby before using the
product.
Top Drawer Front
Panel
9Bottom Drawer
Front Panel (x2)
10 Drawers Base
Panel (x3)
11
Drawers Back
Panel (x3)
14
Drawers support (x3)
15
Drawer Left
Panel (x3)
12 Drawer Right
Panel (x3)
13

8
HARDWARE
www.sweetpeababy.com/help
7
If there are any missing parts, please contact Sweetpea Baby before using the
product.
Bolt 1-3/4” (×16)
ABolt 1-1/8” (×8) BWooden Dowel
1-1/8” (×6)
C
6
Wooden Dowel
3/4” (×12)
M
Curve Washer (×14)
DScrew 1” (×27) E
Screw 1” (×3)
G
Knob (×3)
F
Bracket (×4)
IStraps (x2)
JScrew 1-1/2” (x4) KScrew 3/4” (x4) L
Tools Needed:
Philips Screw Driver
(NOT INCLUDED)
Power drill - 3/32" drill bit
(NOT INCLUDED)
Allen Key (x1)
H

www.sweetpeababy.com/help
8
Bolt 1-3/4” (×6)
AWooden Dowel
1-1/8” (×2)
C
Curve Washer (×6)
D
(2)
(8)
(A,D)
(A)
(D)
1
DRAWER CHEST ASSEMBLY - DRAWER CHEST FRAME ASSEMBLY
1a. Place the Top Rear
Panel (7) and Bottom
Rear Panel (8) as shown
in the illustration on a
soft surface. Align the
Left Side Panel (2).
1b. Insert the two Wooden
Dowels (C) into the
Bottom Front Rail (6)
and attach the same to
the Left Side Panel (2).
1c. Align the Top Front Rail
(4) as depicted in the
diagram, insert the
Curve Washer (D) into
the Bolt (A), use the
same Bolts to attach,
Top Rear Panel (7) and
Bottom Rear Panel (8),
Left Side Panel (2),
Bottom Front Rail (6)
and Top Front Rail (4).
(2)
(6)
(C) (C)
(6)
(4)
(7)
(8)
(2)

www.sweetpeababy.com/help
9
(2)
(B)
(B)
Bolt 1-1/8” (×2)
B
2
DRAWER CHEST ASSEMBLY - DRAWER CHEST FRAME ASSEMBLY
2a. Align the Center Front Rails
(5) to the Left Side Panel (2)
as shown in the diagram.
2b. Attach the same using the
Bolts (B).
(5)
(5)

www.sweetpeababy.com/help
10
Bolt 1-3/4” (×6)
AWooden Dowel
1-1/8” (×2)
C
Curve Washer (×6)
D
(3)
(A,D)
(3)
3
DRAWER CHEST ASSEMBLY - DRAWER CHEST FRAME ASSEMBLY
3a. Align the Right Side Panel (3)
to the above made assembly
as shown.
3b. Insert the two Wooden
Dowels (C) into the Bottom
Front Rail (6) and attach the
same to the Right Side Panel
(3).
3c. Insert the Curve Washer (D)
into the Bolt (A), use the
same Bolts to attach, Top
Rear Panel (7) and Bottom
Rear Panel (8), Right Side
Panel (3), Bottom Front Rail
(6) and Top Front Rail (4).
NOTE: Please do not
overtighten the bolts.
(6)
(C) (C)
(3)

www.sweetpeababy.com/help
11
Bolt 1-1/8” (×2)
B
4
DRAWER CHEST ASSEMBLY - DRAWER CHEST FRAME ASSEMBLY
4a. Attach both Center Front Rails
(5) to the Right Side Panel (3)
using the Bolts (B).
NOTE: Please do not overtighten
the bolts
(B)
(B)
(B)
(B)
(3)

www.sweetpeababy.com/help
12
Bolt 1-1/8” (×4)
B
Wooden Dowel
1-1/8” (×2)
C
Curve Washer (×2)
D
(A,D)
Bolt 1-3/4” (×4)
A
(A)
(A)
(1)
(B)
(B)
(B)
(B)
(C)
(C)
5
DRAWER CHEST ASSEMBLY - DRAWER CHEST FRAME ASSEMBLY
5a. Align the Top Panel (1) onto
the previously made assembly
as shown in the illustration.
5b. Attach the Top Panel (1) using
Wooden Dowels (C) at shorter
Right and Left Side Panels
5c. Insert the Bolts (A) attached
with the Curve Washer (D) into
the insertions on Top Rear
Panel.
5d. Complete the Top Panel
Assembly (1) by inserting the
Bolts (B), Bolts (A) from below
into the grooves as shown in
the illustration.
NOTE: Please do not overtighten
the Bolts.

www.sweetpeababy.com/help
13
6
Wooden Dowel
3/4” (×2)
M
(E)
(E)
(M)
(M)
(15)
(13)
(12)
(11)
(E)
(E)
(9) or (10)
Screw 1” (×4)
E
6
DRAWER CHEST ASSEMBLY - DRAWER ASSEMBLY
6a. Place the Top Drawer Front Panel (9) on
a soft surface, align the Drawer Left
Panel (12) and Right Panel (13) as shown
in the illustration.
6b. Attach the same using Screws (E) on all
four corners of the Front Panel.
6c. Slide the Drawer Base Panel (11) along
the grooves present on the Drawer Left
and Right Panels.
6d. Insert the two Wooden Dowels (M) into
the Drawers support (15) and attach the
same to the Drawer Front Panel (9) .
6e. Similarly, follow the same method to
assemble the bottom drawers using the
Bottom Drawer Front Panels (10).
(15)

www.sweetpeababy.com/help
14
6
Wooden Dowel
3/4” (×2)
M
(G)
(F)
(E)
(E)
(E)
(14)
(14)
Screw 1” (×4)
EScrew 1” (×1)
GKnob (×1)
F
7
DRAWER CHEST ASSEMBLY - DRAWER ASSEMBLY
7a. Align the Drawer Back Panel (14) onto
the above made assembly as shown.
7b. Insert the two Wooden Dowels (M) into
the Drawers support (15) and attach the
same to the Drawer Back Panel (14).
7c. Attach the same using the Screws (E)
on all four corners of the Panel.
7d. Attach the Knob (F) to the Front Panel
(11 or 12) using Screw (G), by inserting
the Screw from behind the Front Panel
passing it through the Knob.
7e. Follow the same instructions for the
rest of the drawers.
(M)
(M)
(15)
(15)

www.sweetpeababy.com/help
15
8
DRAWER CHEST ASSEMBLY - DRAWER CHEST FRAME ASSEMBLY
8a. Insert the assembled drawers into the
grooves present on the Drawer chest frame.
8c. Ensure the right alignment of drawers before
inserting them into the frame.

www.sweetpeababy.com/help
16
“Lift up and Pull”
“Press down and Pull”
1. Open the drawer fully.
2. Locate the quick disconnect levers
on the right and left-hand slides.
3. Simultaneously press the quick
disconnect levers (as shown) while
pulling out the drawer.
DRAWERS REMOVAL

www.sweetpeababy.com/help
17
“Adjust”
(1)
(2)
(3)
“Remove Screws”
“Insert Screws”
1. Remove the
pre-assembled Screws
from the glides on the
Left and Right Panels of
the Drawers.
2. Adjust the glide up and
down as needed.
3. Re-install the above
removed Screws.
DRAWERS TROUBLESHOOTING

www.sweetpeababy.com/help
18
“Click”
1. Take all drawers and slide them
all the way gently (the rollers on
drawer slide at both sides of
drawers are to go into the track
of the slide at each side panel)
one by one, starting from the
bottom.
DRAWERS TROUBLESHOOTING

www.sweetpeababy.com/help
19
9a. Determine the desired location of the
dresser. Find a wall stud behind the
furniture piece and position one of
the Brackets (I) vertically on the stud
approximately 1" below the top of the
dresser piece. Mark and drill a pilot
hole in the center of the stud with a
3/32" drill bit. Attach the Bracket (I) to
stud with the two Screws (K).
9b. The second bracket will need to be
attached horizontally to the top of the
dresser frame. Temporarily move the
dresser away from the wall and place
a bracket near the top of the frame.
Mark and drill holes for screws with a
3/32" drill bit. Attach the bracket to
the dresser piece with the two
Screws (L).
9c. Move the dresser piece into its final
position, taking care to line up the
wall bracket with the dresser bracket.
Thread the strap through the
brackets as shown in the illustrations.
Tighten the strap until snug. Note: Do
not overtighten. Similarly, follow the
steps for the other side of the
furniture.
9
ANTI-TIP SAFETY HARDWARE INSTALLATION
WALL
WALL
WALL
WALL
WALL
FURNITURE
FURNITURE
FURNITURE
FURNITURE
(K)
(L)
(I)
(J)
(J)
FURNITURE
WALL
“Pull Down To Tighten”
“Insert”
“Insert”
1 2 3

www.sweetpeababy.com/help
20
FURNITURE CARE INSTRUCTIONS
ROOM CLIMATE CONTROL:
• Wood, when first cut contains more than 50 percent water. When it is prepared for
furniture construction it is placed in a Kiln and the moisture content is brought down
to 8 to 10 percent. Wood is porous and responds to its environment. If the room has
high humidity it will absorb it and expand and if the humidity is low it will lose
moisture and shrink.
• It is important that the humidity levels in the room be controlled from extremes of
too much humidity or too little. Furniture should not be placed close to the
air-conditioning outlets, fire places, radiators, space heaters, humidifiers or
dehumidifiers. Exposure to extreme variations of temperature and humidity can
damage any fine wood product.
THE IDEAL ENVIRONMENT FOR FINE FURNITURE:
• Fine wood furniture will have fewer problems when its environment is controlled at a
temperature between 65 and 75 degrees and a relative humidity between 35 and 40
percent. Wood placed in an environment outside of those limits can and will shrink
or expand and may develop some small cracks which are not material or structural
defects.
STICKING DOORS AND DRAWERS:
• With the minor changes in temperature and humidity, doors and drawers may swell
and be difficult to open or close. Tolerances have been built into the units but
extreme conditions may still cause sticking. This will adjust back to normal over
time but until it does consider using a dehumidifier or rub candle wax or paraffin on
sides that stick.
AVOID DIRECT SUNLIGHT:
• Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some
cases darken them. It can also cause crazing or hair line cracks in the finish. White
finishes will yellow naturally over time and exposure to direct sunlight will hasten
this natural process along with some woods darkening naturally over time; this is
not considered to be a quality defect.
PROPER STORAGE:
• If you need to put your furniture in storage for any period of time do not store them
in a damp basement or hot dry attic. Allow air movement around the furniture and
do not stack anything on it.