Sweetpea Baby ROSE DOUBLE DRESSER User manual

Read all instructions before
assembling and using product.
IMPORTANT - Keep instructions for
future use. 0222R1-781
Owner’s Manual
ROSE DOUBLE DRESSER
Scan the QR code to register your product
https://www.sweetpeababy.com/customer-care/product-registration/

Contact Sweetpea
Baby in case of any
assistance needed.
2www.sweetpeababy.com/help
SAFETY TIPS
Adult Assembly
Required.
DO NOT use the
product if it is
damaged, broken,
and/or components are
missing or broken.
To protect your parts
during assembly,
please place them on a
soft surface.
Small parts may
present choking
hazard prior to
assembly.
Please read the
instructions
thoroughly. Identify all
parts & hardware.
Improper or unsafe use
of power drills/drivers
can result in death or
serious injury.
To clean surface, use
only water on a damp
cloth. Do not use
window cleaner or
cleaning abrasive as it
will scratch the surface
and could damage the
protective coating.
0-6
Always monitor your
child’s activity in the
nursery or near
furniture.

…. for choosing Sweetpea Baby and congratulations on joining our family;
a family that has been transforming lives for over 30 years!
We appreciate your feedback and wish you the very best in the
coming years with your new addition. If you have any questions
or concerns please don’t hesitate to reach out to us. One of our
trusted Customer Care representatives will be happy to assist you.
Thank you again for entrusting us to provide you with safe
and affordable baby products and accessories.
THANK YOU...
LIMITED WARRANTY:
• Sweetpea Baby warrants its product to be free from defects in material
and workmanship and agrees to remedy any such defect.
• This warranty covers 1 year from the date of original purchase.
• This warranty is valid only upon presentation of proof of purchase.
• This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
• This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
• This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
www.sweetpeababy.com/help
3

WARNINGS
www.sweetpeababy.com/help
4
• FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
• CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS
OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE.
• DO NOT USE THIS DRESSER IF ANY PARTS ARE MISSING, DAMAGED OR BROKEN.
CONTACT SWEETPEA BABY - 1532 S. WASHINGTON AVE, PISCATAWAY, NJ 08854
FOR REPLACEMENT PARTS.
• IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
• SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM FURNITURE TIP-OVER.
TO HELP PREVENT THIS, PLACE THE HEAVIEST ITEMS ON THE LOWER SHELVES AND
DRAWERS. DO NOT SET HEAVY OBJECTS ON TOP SHELVES AND DRAWERS.
• NEVER OPEN MORE THAN ONE DRAWER AT A TIME.
• THE USE OF TIP-OVER RESTRAINTS MAY REDUCE BUT NOT ELIMINATE THE RISK OF
TIP-OVER.
• DO NOT SET TVs OR OTHER HEAVY OBJECTS ON TOP OF THIS PRODUCT.
• ALWAYS MONITOR YOUR CHILD’S ACTIVITY WHEN IN THE NURSERY.
• NEVER ALLOW CHILDREN TO CLIMB OR HANG ON DRAWERS, SHELVES, AND DOORS.
• DO NOT ALLOW CHILDREN STANDING IN DRAWERS.
• DO NOT ALLOW CHILDREN STANDING ON TOP OF THIS PRODUCT.
• TO AVOID HEAD INJURY, DO NOT ALLOW CHILDREN TO PLAY UNDERNEATH OPEN
DRAWERS.
• DO NOT LEAVE DRAWERS OPEN WHEN IN USE.
• ACCESSORY ITEMS MUST BE SECURELY FASTENED TO THIS PRODUCT ACCORDING
TO THE INSTRUCTIONS PROVIDED WITH THOSE ITEMS.
CHILDREN HAVE DIED FROM FURNITURE TIPOVER, TO REDUCE THE RISK OF
TIPOVER :
• ALWAYS INSTALL TIPOVER RESTRAINT PROVIDED.
• NEVER PUT A TV ON THIS PRODUCT.
• NEVER ALLOW CHILDREN TO STAND, CLIMB OR HANG ON DRAWERS, DOORS OR
SHELVES.
• NEVER OPEN MORE THAN ONE DRAWER AT A TIME.
• PLACE HEAVIEST ITEMS IN THE LOWER DRAWERS.

www.sweetpeababy.com/help
5
PARTS
If there are any missing parts, please contact Sweetpea Baby before using the
product.
Dresser Top Panel
1Dresser Left
Side Panel
2Dresser Right
Side Panel
3
Dresser Center
Panel
4Dresser Top Front
Rail
5Dresser Center
Front Rail (x2)
6
Dresser Bottom Front
Rail
7Dresser Center
Support Leg
8Dresser Top Rear
Panel
9

www.sweetpeababy.com/help
6
PARTS (Cont.)
If there are any missing parts, please contact Sweetpea Baby before using the
product.
Dresser Bottom Rear
Panel
10 Top Drawer Front
Panel (x2)
11 Bottom Drawer
Front Panel (x4)
12
Drawers Base
Panel (x6)
13
Drawers Back
Panel (x6)
16
Drawer Left
Panel (x6)
14 Drawer Right
Panel (x6)
15

HARDWARE
www.sweetpeababy.com/help
7
If there are any missing parts, please contact Sweetpea Baby before using the
product.
Bolt 1-3/4” (×19)
ABolt 1-1/8” (×10) BWooden Dowel
1-1/8” (×11)
C
Curve Washer (×17)
DScrew 1” (×48) E
Screw 1” (×6)
GAllen Key (x1) H
Knob (×6)
F
Bracket (×4)
I
Straps (x2)
JScrew 1-1/2” (x4) KScrew 3/4” (x4) L
Tools Needed:
Philips Screw Driver
(NOT INCLUDED)
Power drill - 3/32" drill bit
(NOT INCLUDED)

www.sweetpeababy.com/help
8
Bolt 1-3/4” (×6)
AWooden Dowel
1-1/8” (×2)
C
Curve Washer (×6)
D
(2)
(2)
(2)
(9)
(10)
(10)
(5)
(A)
(D)
(A,D)
1
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
1a. Place the Dresser Top Rear
Panel (9) and Dresser Bottom
Rear Panel (10) as shown in
the illustration on a soft
surface. Align the Dresser
Left Side Panel (2).
1b. Insert the two Wooden
Dowels (C) into the Dresser
Bottom Front Rail (7) and
attach the same to the
Dresser Left Side Panel (2).
1c. Align the Dresser Top Front
Rail (5) as depicted in the
diagram, insert the Curve
Washer (D) into the Bolt (A),
use the same Bolts to attach,
Top Rear Panel (9) and
Dresser Bottom Rear Panel
(10), Left Side Panel (2),
Bottom Front Rail (7) and Top
Front Rail (5).
(7)
(C)
(C)
(7)

www.sweetpeababy.com/help
9
(2)
(B)
(B)
Bolt 1-1/8” (×2)
B
(6)
(6)
2
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
2a. Align the Dresser Center
Front Rails (6) to the Dresser
Left Side Panel (2) as shown
in the diagram.
2b. Attach the same using the
Bolts (B).

www.sweetpeababy.com/help
10
Bolt 1-1/8” (×1)
BWooden Dowel
1-1/8” (×2)
C
(4)
(4)
(8)
(8)
(B)
(C) (C)
3
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
3a. Place the Dresser Center Panel
(4) on a soft surface and attach
the Dresser Center Support Leg
(8) as shown in the illustration
by inserting the Wooden
Dowels (C) from below the
Center Panel.
3b. Attach the same by inserting
the Bolt (B) from above the
Center Panel (4) through the
Center Support Leg and tighten.

www.sweetpeababy.com/help
11
(C)
(A,D)
Bolt 1-3/4” (×1)
AWooden Dowel
1-1/8” (×1)
C
Curve Washer (×1)
D
(7)
(7)
(4)
(5)
(4)
(5)
4
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
4a. Insert the above assembled
Center Panel into the previously
assembled Rear Panel and Left
Panels assembly.
4b. Attach the Dresser Top Front
Rail (5) to the Center Panel (4)
using the Wooden Dowel (C) in
the between them.
4c. Similarly, insert the Curve
Washer (D) into the Bolts (A),
insert the same into the
insertion at the center of the
Center Panel (4) from below as
depicted in the diagram.

www.sweetpeababy.com/help
12
(A,D)
Bolt 1-3/4” (×6)
AWooden Dowel
1-1/8” (×2)
C
Curve Washer (×6)
D
(3)
(3)
5
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
5a. Align the Dresser Right Side
Panel (3) to the above made
assembly as shown.
5b. Insert the two Wooden
Dowels (C) into the Dresser
Bottom Front Rail (7) and
attach the same to the
Dresser Right Side Panel (3).
5c. Insert the Curve Washer (D)
into the Bolt (A), use the
same Bolts to attach, Top
Rear Panel (9) and Dresser
Bottom Rear Panel (10),
Right Side Panel (3), Bottom
Front Rail (7) and Top Front
Rail (5).
NOTE: Please do not
overtighten the bolts.
(7)
(C)
(C) (3)

www.sweetpeababy.com/help
13
Bolt 1-1/8” (×2)
B
(B)
(6)
(6) (B)
(3)
6
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
6a. Attach both Dresser Center
Front Rails (6) to the Dresser
Right Side Panel (3) using the
Bolts (B).
NOTE: Please do not overtighten
the bolts

www.sweetpeababy.com/help
14
Bolt 1-1/8” (×4)
B
Wooden Dowel
1-1/8” (×4)
C
Curve Washer (×4)
D
(A,D)
Bolt 1-3/4” (×6)
A
(B)
(A)
(A)
(B)
(1)
(B)
(B)
(B)
(B)
(C)
(C)
(C)
7
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
7a. Align the Dresser Top Panel (1)
onto the previously made
assembly as shown in the
illustration.
7b. Attach the Top Panel (1) using
Wooden Dowels (C) at shorter
Right and Left Side Panels and
Center Panel.
7c. Insert the Bolts (A) attached
with the Curve Washer (D) into
the insertions on Center Panel
and Top Rear Panel.
7d. Complete the Top Panel
Assembly (1) by inserting the
Bolts (B), Bolts (A) from below
into the grooves as shown in
the illustration.
NOTE: Please do not overtighten
the Bolts.

www.sweetpeababy.com/help
15
(E)
(E)
(E)
(14)
(15)
(13)
(E)
(11) or (12)
Screw 1” (×4)
E
8
DRESSER ASSEMBLY - DRAWER ASSEMBLY
8a. Place the Top Drawer Front Panel (11)
on a soft surface, align the Drawer Left
Panel (14) and Right Panel (15) as
shown in the illustration.
8b. Attach the same using Screws (E) on
all four corners of the Front Panel.
8c. Slide the Drawer Base Panel (13) along
the grooves present on the Drawer
Left and Right Panels.
8d. Similarly, follow the same method to
assemble the other top drawer and the
bottom drawers using the Bottom
Drawer Front Panels (12).

www.sweetpeababy.com/help
16
(E)
(E)
(G)
(F)
(E)
(E)
(16)
Screw 1” (×4)
EScrew 1” (×1)
GKnob (×1)
F
9
DRESSER ASSEMBLY - DRESSER ASSEMBLY
9a. Align the Drawer Back Panel (16) onto
the above made assembly, and attach
the same using the Screws (E) on all
four corners of the Panel.
9b. Attach the Knob (F) to the Front Panel
(11 or 12) using Screw (G), by inserting
the Screw from behind the Front Panel
passing it through the Knob.
9c. Follow the same instructions for the
rest of the drawers.

www.sweetpeababy.com/help
17
Bolt 1-1/8” (×1)
B
(B)
10
DRESSER ASSEMBLY - DRESSER FRAME ASSEMBLY
10a. Insert the Bolt (B) into the Bottom Rear
Panel (10).
10b. Insert the assembled drawers into the
grooves present on the dresser frame.
10c. Ensure the right alignment of drawers
before inserting them into the frame.
(10)

www.sweetpeababy.com/help
18
“Lift up and Pull”
“Press down and Pull”
1. Open the drawer fully.
2. Locate the quick disconnect levers
on the right and left-hand slides.
3. Simultaneously press the quick
disconnect levers (as shown) while
pulling out the drawer.
DRAWERS REMOVAL

www.sweetpeababy.com/help
19
“Adjust”
(1)
(2)
(3)
“Remove Screws”
“Insert Screws”
1. Remove the
pre-assembled Screws
from the glides on the
Left and Right Panels of
the Drawers.
2. Adjust the glide up and
down as needed.
3. Re-install the above
removed Screws.
DRAWERS TROUBLESHOOTING

www.sweetpeababy.com/help
20
“Click”
1. Take all drawers and slide them
all the way gently (the rollers on
drawer slide at both sides of
drawers are to go into the track
of the slide at each side panel)
one by one, starting from the
bottom.
DRAWERS TROUBLESHOOTING