Swegon GOLDen GATE User manual

GB.TBLZ3112.220412
www.swegon.com 1
We reserve the right to alter specifications without notice.
INSTALLATION
GOLDen GATE, TBLZ-1/2-1-3-41
1. General
Kommunikationsenhet TBLZ-1/2-1-3-41 är avsedd att
användas till luftbehandlingsaggregat GOLD version 4, A
och B.
Enheten består av:
1. 4-modulers normkapsling för din-skenemontage IP20.
2. 9-pol d-subkontakt för anslutning via seriekabel till
GOLD eller modem.
3. Plint för kraftmatning 9-24 V AC/DC, 165 mA vid 12V.
4. RJ-45 kontakt för Ethernetanslutning.
5. Plint för två digitala ingångar.
Other features:
Module LED.
RX LED.
Link LED.
GOLD Comm. LED.
2. Safety Precautions
Be careful whenever you do any wiring to the unit.Never
carry out any work on the unit while the power supply is
switched on. Doing so could harm you and damage the
unit.
Observe local electrical safety regulations as you install the
unit.
3. Installation
3.1 General
Connect conductors to the V in+ and V in- terminals (see
Fig. 1) of the GOLDen GATE unit and wire them to a sepa-
rate power supply unit with the correct capacity or to the
12 V DC or 24 V AC terminals of the GOLD air handling
unit.
NOTE! The polarity G and G0 is important.
Configure the communication unit using the configura-
tion program available from our website address: http://
www.swegon.com. Install the program according to the
instructions in the setup window.
Fig. 1
3
2
1
4
5

GB.TBLZ3112.220412
2 www.swegon.com We reserve the right to alter specifications without notice.
Direct with cable
Power
Ethernet cable
Via network
Straight
Ethernet cable
This confi guration requires the use of a computer with an
Ethernet port. Connect both the unit and computer to the
same network.
Start the configuration program and select Ethernet, see
Fig. 2. The program will now scan the network to seek the
GOLDen GATE unit.
All the units connected are shown on a list, see Fig. 3.
Double click on the unit desired and enter the IP addres-
ses. As standard, “admin” is used both as the user name
and the password, see Fig. 4.
The unit can be configured via our integrated webpage
for both mail, master and PPP function with links to other
GOLDen GATE units in the same network.
If you know the IP address, you can also configure the unit
via its own built-in webpage.
After you’ve saved your settings, you’ll have to reboot the
unit before your settings will be effective.
Locate the communication unit next to the junction hood
on the GOLD air handling unit. Depending on the enclo-
sure requirements called for by the application, an extra
enclosure conforming to a higher enclosure class may be
required.
Connect the network.
Power
Fig. 2
Fig. 3
Fig. 4

GB.TBLZ3112.220412
www.swegon.com 3
We reserve the right to alter specifications without notice.
3.2 GOLD Version 4/A
Connect the serial cable supplied with 9-pin D-subconnec-
tor and circular connector to the socket on the GOLD (see
arrow in Fig. 5).
3.3 GOLD Version B
Run the serial cable supplied through the GOLD air hand-
ling unit cable lead-through and connect it to the socket
located inside the GOLD (see Fig. 6 and 7).
4. Commissioning
4.1 GOLD Version 4/A
Set the LON Communication to “0” in the service menu.
4.2 GOLD Version B
GOLD units with Program Version 1.11: DIP-switch 3 must
be in the ON position and DIP-switch 4 in the OFF position
on the GOLD AHU control unit: (see Fig. 7).
GOLD units with Program Version 1.12 and better: DIPs-
witch 3 must be in the OFF position and DIP-switch 4 must
be in the in the ON position on the GOLD AHU control
unit (see Fig. 7).
GOLD
Power Junction hood viewed from the rear
Cable lead-through
For GOLDen GATE cable
Control unit
Dip switch
Fig. 5
Fig. 6
Fig. 7

GB.TBLZ3112.220412
4 www.swegon.com We reserve the right to alter specifications without notice.
5. Digital inputs
(Applicable to Program Version 4.00.0 and newer)
5.1 General
The unit is equipped with 2 digital inputs. The status of
the inputs can then be read as 2 parameters in the report
(Digital in 1 and Digital in 2) via the network.
If the built-in web page is used, the inputs are designed
for forwarding alarms. Provision is available for free alarm
text and input inversion. It is also possible to email alarms.
5.2 Electrical connection
The digital input is rated for a 9-24 V DC supply. The con-
trol unit of the Version B GOLD units has terminal blocks
for supplying 12 V DC current.
9 - 24 VDC
COM DI1 DI2
6. General Explanations
Module LED
LED shines orange during start-up; then shines
green while the unit is energized.
LED flashes green while configuration is in progress.
LED flashes red if the memory malfunctions.
LED shines red in the event of a serious fault in the
hardware.
GOLD Comm.
LED fl ashes green while communication between
the GOLD and the GOLDen GATE is in progress.
LED shines red if an error in communication occurs
between the GOLD and the GOLDen GATE.
LED is not lit while there is no traffi c between the
GOLD and the GOLDen GATE.
RX
LED fl ashes green while there is traffic on the
Ethernet network.
Link
LED is not lit if a link to the Ethernet network is
down.
LED shines with a steady green glow if the unit is
connected to a 10 Mbit/s network.
LED shines with a steady orange glow if the unit is
connected to a 100 Mbit/s network.
The various parameters available and protocol-specific
properties are documented in separate product leaflets.
These leaflets can be downloaded from our website:
www.swegon.com.
The GOLD air handling unit operates independently
regardless of whether or not the network is active.
+-