SY-SUMBOY ZX-GZ5-C2V3 User manual

1
Video Converter
ZX-GZ5-C2V3
User Manual
V2.0
Shenyang Sumboy Intelligent Imaging Technology Co., Ltd.
No.24 Shiji Rd., Hunnan Dist., Shenyang, Liaoning Prov.,
Tel: [phone]
Fax: [phone]
www.irseen.com

2
CONTENT
NOTICE ...........................................................................................................................................................3
PACKAGE LIST ...............................................................................................................................................4
CONNECTION INSTRUCTION.......................................................................................................................5
TROUBLESHOOT............................................................................................................................................. 6
PIN DEFINITION.............................................................................................................................................. 6

3
Notice
In order to ensure the instruments are in good technical
condition, the daily maintenance of the operating personnel is
only limited to the replacement and inspection of cables,
cleaning and functional inspection.
Please do not open the cabinet in any case even if the system
runs into malfunction. Troubleshooting has to be taken on by
professional technicians after thorough examinations.
The video tracker should be kept in a cool, dry environment for
storage.
Please make sure that the connector assemblies were inserted
after aligned with sockets. Please do not pull the cable directly
for unplugging.
Wearing anti-static gloves when using and connecting the
product to prevent it from being penetrated.
The power input voltage of the video tracker should be 12V,
otherwise the device would be damaged.

4
Package List
Video Converter×1
Sony Camera Core×1 (optional or
purchased by user)
6pin (TTL) testing cable×1
30pin cable×2
Ethernet cable×1
30pin HDMI converting board×1
(optional)
Attention: please insert power as the final step so as to prevent the device from
being damaged, make sure all pins are properly inserted.

5
Connection Instruction
Pic 1 Front side interfaces
Pic 2 Side interfaces
Pic 3 Side interfaces
Pic4 Connections as a whole
SD card
Video input
(30PIN cable---Sony camera)
Connect to 6pin
testing cable
Do NOT insert upgrading interface (7 pin)
Video output
(30PIN cable---converting board)
Ethernet

6
Troubleshoot
Please use the form below to check the infrared camera when it
has any trouble. Disconnect the power and contract our technical
support department if the problem cannot be fixed.
Malfunction
Reason and solution
Video tracker cannot
start/Power light is not on
1. Check whether the power is connected.
2. Check whether the voltage is lower than required
which should be 12V.
No image display
1. Check whether the serial port is open(not serial port 1)
2. Check whether the baud rate setting of the operation
software is correct.
3. Check whether the video output format of the
displayer is 1080I/1080P.
The serial command does not
respond
1. Check whether the serial port is open (not serial port 1
open) Check whether the verification mode is correct.
No tracking box
1. The target is too close or not obvious, reselect target.
Pin Definition
Pin #
Pin Title
Function
1
POWER IN
+12V power input
2
POWER IN
+12V power output
3
GND
GND
4
GND
GND
5
RXD
Serial port receive
6
TXD
Serial port send
Testing Cable interface

7
Ethernet interface
Ethernet pin definition
Pin #
Pin Title
Function
1
DATA_1_N
TX_N
2
DATA_1_P
TX_P
3
DATA_0_N
RX_N
4
DATA_0_P
RX_P
30pin definition
#
Video input
#
Video output
1
TXOUT3+
1-2
NC
2
TXOUT3-
3
GND
3
TXCLKOUT+
4
TXD_30pin
4
TXCLKOUT-
5
RXD_30pin
5
TXOUT2+
6-10
NC
6
TXOUT2-
11
GND
7
TXOUT1+
12-14
NC
8
TXOUT1-
15
HDMI_HPD
9
TXOUT0+
16
HDMI_OUT_5V
10
TXOUT0-
17
HDMI_SDA
11
GND
18
HDMI_SCL
12
RXD
19
HDMI_CEC
13
TXD
20
GND
14-18
DC IN=10V
21
HDMI_CLK_N
19-20
GND
22
HDMI_CLK_P
21-30
NC
23
HDMI_D0_N
24
HDMI_D0_P
25
GND
26
HDMI_D1_N
27
HDMI_D1_P
28
HDMI_D2_N
29
HDMI_D2_P
30
GND
Video input
Video output