1
Operating Instructions
Waterproof T-Cable Connector, IP68
Item no: 2758025
1 Intended use
The product is a waterproof T-cable connector with 5-pin terminal block.
The product has an IP68 ingress protection rating. It provides total protection against small
particles (e.g. dust, dirt). The product is water resistant up to 1 m for 1 hour.
The product is suitable for outdoor use.
If you use the product for purposes other than those described, the product may be dam-
aged.
Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product
available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights
reserved.
2 Delivery contents
■Product
■Operating instructions
3 Latest product information
Download the latest product information at www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
4 Description of symbols
The symbol warns of hazards that can lead to personal injury.
Read the operating instructions carefully.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
5.1 General
■The product is not a toy. Keep it out of the reach of children and pets.
■Do not leave packaging material lying around carelessly. This may become dangerous
playing material for children.
■If you have questions which remain unanswered by this information product, contact our
technical support service or other technical personnel.
■Maintenance, modifications and repairs must only be completed by a technician or an
authorised repair centre.
5.2 Handling
■Handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
5.3 Operating environment
■Do not place the product under any mechanical stress.
■Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam
and solvents.
5.4 Operation
■Consult an expert when in doubt about the operation, safety or connection of the
product.
■If it is no longer possible to operate the product safely, take it out of operation and pro-
tect it from any accidental use. DO NOT attempt to repair the product yourself. Safe op-
eration can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
5.5 Connected devices
■Also observe the safety and operating instructions of any other devices which are con-
nected to the product.
5.6 Electrical installation
WARNING!Safety hazard!
The product should only be installed by people with relevant electrical knowledge and exper-
ience! *)
If it is not installed properly, you risk:
■your own life
■the life of user of the electrical device
■severe damage to property, e.g., by fire
■personal liability for personal injury and material damage
Always consult an electrician!
*) Technical knowledge required to perform the installation:
For the installation, the following specialist knowledge is required in particular:
■The “Five safety rules”: Disconnect from the mains; protect against accidental switch-on;
ensure there is no voltage; earth and short-circuit; cover or protect adjacent live parts
■Use of suitable tools, measuring devices and personal protective equipment, where ne-
cessary
■Analysis of measurement results
■Use of electrical installation materials to meet the requirements for disconnection
■IP protection ratings
■Installation of electrical installation materials
■Type of power supply (TN system, IT system, TT system) and the corresponding con-
nection criteria (classic earthing, protective earthing, necessary additional measures etc.)
If you are not a professional, do not do it yourself, have it performed by a specialist.
6 Product overview
1 Lock nut 2 Sealing tube
3 Sealing ring 4 Wire clamp
5 Terminal case 6 5-wire connection terminal
7 O-ring
7 Connection
Important:
– Make sure the wires match the polarity markings shown on the terminal connector.
– The connections at both ends of the terminal connectors must match.
– Double check all wires are properly inserted and secured using the terminal screws.
– Sealing rings and tubes must be properly fitted and locking nuts securely fastened.
Strip cables, wire length 6.5 cm (±0.5 cm).
8 Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
Wipe the product with a fiber free cloth if needed.
