Sylvania SRCD268BT User manual

MODEL NO. SRCD268BT
OWNER'S MANUAL
BLUETOOTH PORTABLE CD RADIO
BOOMBOX
PLEASE READ BEFORE USING THIS UNIT

1

2

3

4
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.

5
Control Location (Top Views)
Control Location (RearView)
HANDLE
CD DOOR
AUX IN JACK
VOLUME KNOB
STAND BY BUTTON
FM ROD ANTENNA
TUNING KNOB
AC SOCKET
BATTERIES
COMPARTMENT
PROGRAM BUTTON
REPEAT BUTTON
PLAY/PAUSE BUTTON
STOP/BLUETOOTH PAIR BUTTON
SKIP FORWARD BUTTON
SKIP BACKWARD BUTTON
POWER
REPEAT PROGRAM
PLAY/PAUSE
BLUETOOTH INDICATOR
POWER INDICATOR
REPEAT INDICATOR
PLAY/PAUSE INDICATOR
PROGRAM INDICATOR
TRACK DISPLAY (CD ONLY)
FUNCTION SWITCH
(AM/FM/CD/BLUETOOTH)

6
Connecting AC Power
Connect the small end of AC cord to the socket at the back of the main unit and insert the
plug of AC cord into standard AC wall outlet.
Battery Operation
Before installing batteries (not included), ensure
that the unit is disconnected from the mains
supply.
Remove the battery compartment cover on the
bottom of the unit by sliding the battery cover with
the opening direction indicated on the battery
cover.
Install 8 pieces of 1.5V (UM2) batteries (not
included) by following the polarity markings and
then replace the cover.
For battery operation, unplug the AC cord from
the AC wall outlet first and then remove the AC cord from the socket at the back of the main
unit.
Caution:
The unit is designed to operate from mains supply of AC 120V~60Hz. If the plug of
AC cord does not fit properly, try to turn it over and try again. Do not force it.
When the unit is intended for being unused for a long period of the time. Please press
the button to turn off the unit and unplug the power cord from the AC wall
outlet. AC
Power Connection
STAND BY

Switching On for the first time
Plug into AC power or install batteries by following instructions on the previous Power
C
the unit. The POWER indicator will be lighted off.
To turn the unit off, press the button again to turn the unit off.
onnection section. The POWER indicator willl lit. Press the STAND BY button to turn on
Switching between different sources (AM/FM/CD/BLUETOOTH)
After turning on the unit, press and toggle FUNCTION switch to select different sound
sources.
Adjusting sound volume level
After turning on the unit, turn the VOLUME knob to adjust the level of sound volume.
Adjusting the rod antenna
The aerial should be extended to ensure good reception in both FM radio modes. It may be
necessary to adjust the position of the unit and /or aerial position to achieve the best signal
reception.
Main Operation
Caution:
There is a danger of explosion if batteries are replaced incorrectly.
Replace batteries with the same type and same brand only.
When the unit is intended for being unused for a long period of the time, press the
POWER button to turn OFF the unit and remove all batteries from the main unit.
6
STAND BY

8
The unit is designed to play normal music CD disc bearing the correct
identification logo. If the disc does not confirm tothe standard, it may not
be played back properly.
Loading disc
1. Press and toggle the FUNCTION button to switch to CD mode.
2. Press down the OPEN/CLOSE AREA on the CD door on the top of the unit to unlock
and open the CD door.
3. Hold the CD disc by its edge with CD graphical side facing up and put it onto the CD
compartment after the CD door is opened. Make sure that the disc label is facing up.
4. Close the CD door and make sure the VOLUME knob is not in minimum position.
CD playback
After loading the disc, the disc will begin spinning and the total number of the tracks on the
disc will be shown on the display and the first track/file on the CD will be played back
automatically.
Play/Pause Control
To pause playback temporarily by pressing the PLAY/PAUSE button. Music playback will
be paused and the current elapsed track number will be shown on the display and the play
icon will be blinking. Press the PLAY/PAUSE button again to resume playback.
Stop playback
To stop playback, press the STOP button on the unit. The total number of tracks of the disc
will be displayed.
Caution:
Playback of CD-R / CD-RW may depend on recording conditions.
Do not attach a seal or label to either side (the recordable side or the labeled side) of a
CD-R/ RW disc. It may cause malfunction.
Do not load a blank CD-R/ RW disc. It will take over 1 minute to read the disc. The disc
may be damaged if you try to open the CD Door while reading the disc.
CD-ROM
,
CD-I
,
CDV
,
VCD
,
DVD or com
p
uter CDs are not
p
ossible to be read.
Remark:
If there is no disc in the unit, “NO” will be indicated on the display.
If the CD cannot be read
,
“NO” will be indicated on the display.
CD Operation
Skip track
During playback, press the forward or backward SKIP buttons to skip to the next or
previous tracks.
High-speed music search
During playback, press and hold the forward or backward SKIP buttons to skip/search
through the current track at high speed in forward or backward directions. When the SKIP
buttons are released, normal playback speed will be resumed immediately.

•Press the   button to turn on the unit.
•Press and toggle the FUNCTION button to select Bluetooth mode. The unit will
search the paired device with the “BLUETOOTH” Indicator lit.
•Press and hold the STOP/PAIR Button for 4~5 seconds. Then the “BLUETOOTH”
Indicator is flashing, the unit will goes into Pairing/Discoverable mode.
•Turn on the Bluetooth function of your Bluetooth device and enable the search or
scan function to find the unit.
•Select "SRCD268BT" from the device list when it appears on your device screen. If
required, enter the pass code “0000” to pair (link) the unit with your device.
•After successfully pairing (linking) the Bluetooth enabled device the “BLUETOOTH”
Indicator steadily and a short beep will heard.
Note: If you can’t pair the unit with your Bluetooth enabled device, you can try to turn Off &
On the power of your unit to solve the problem.
1. If the unit has never been paired with a Bluetooth device before, you need to follow the
pairing instructions below to link the SRCD268BT with your Bluetooth device.
Bluetooth Operation
9
Repeat playback modes (Repeat 1 / Repeat all)
Repeat the Current Track
Repeat All Tracks
During playback, press the REPEAT button twice to repeat the entire album.
Return to normal playback
Press the REPEAT button until NO repeat indicator is displayed. The normal playback
will be resumed.
During playback, press the REPEAT button once to repeat the current CD track.
Programmed CD playback
This unit can be programmed to play up to 20 tracks in CD mode. Load the music CD disc
onto the CD compartment (without pressing the “PLAY/PAUSE” button)
1. Press PROGRAM button once in the stop mode. “P01” will be shown on the display
and blinking.
2. Press the SKIP buttons to select the desired track to be programmed.
3. Press PROGRAM button again to save the selected track/files.
4. Repeat steps 2-3 to program up to 20 tracks.
5. Press the PLAY/PAUSE button to play the programmed tracks after programming is
completed. The “PROG” indicator will lit.
6. To clear program and resume normal playback, press the STOP button twice during
playback, or open the CD door, or change to next mode to clear the programmed tracks.
Remark:
The unit can store up to 20 tracks in the programmable memories. During the
pro
g
rammed pla
y
back, user can still select the “repeat 1 / repeat all” functions.
CD Operation-Continued