Symcod LS6300 User manual

Manual
LS6300
Laser Barcode Scanner
Version: 30/04/2013
WWW.SYMCOD.COM

Introduction
The Symcod LS6300 is an affordable scanner solution for operation
management. Always looking for reliable and economical solution, this
model has been specially selected by Symcod for its excellent value for
money. Recommended for light industrial operation, it is design without
mechanical moving parts which is an asset.
Examples of uses
•Time & attendance
•Inventory management
•Document tracking and more
Characteristic
•Built-in 1D laser engine, no moving parts
•Multi-selection for different use
•High resolution up to 4 mils
•Multi-interface

1
Programmation guide
1. Use the cable required for the selected interface
2. Connect the cable to the device
3. Scan the « Default » code to reset the scanner to the factory configuration.
4. Go to « OUTPUT MODE » section
5. USB configuration, scan code under : “OUTPUT MODE – KEYBOARD / USB”
6. RS-232 configuration, scan code under : “OUTPUT MODE – SERIAL RS232”
RESET CONFIGURATION TO DEFAULTS
OUTPUT MODE –
KEYBOARD / USB
OUTPUT MODE –
SERIAL RS232
OUTPUT
MODE
OUTPUT MODE – WAND
RS-232
USB

2
Multi-Interface Functions – 1
GOOD READ BEEP TONE
NONE
BUZZER /
LED
GOOD READ BEEP TONE
RESET
DECODE OPTIONS REVERSE IMAGE –
ENABLE
IMAGE
DECODE OPTIONS REVERSE IMANGE
DISABLE
DECODE OPTIONS SEND BAR CODE ID -
DISABLE
CODE ID
DECODE OPTIONS SEND BAR CODE
ID – AS A PREFIX
DECODE OPTIONS SEND BAR CODE ID -
RESET
DECODE OPTIONS SEND BAR CODE
ID – AS A SUFFIX

3
Multi-Interface Functions – 2
SCAN MODE
SINGLE SCAN
READING
MODE
SCAN MODE – SINGLE SCAN NO
TRIGGER
SCAN MODE – MULTISCAN SCAN MODE – MULTISCAN
NO TRIGGER
SCAN MODE - PULSE
LASER/CCD TIMEOUT
5 SECONDS
LASER/CCD TIMEOUT
2 SECONDS
LASER/CCD PULSE RATE - 7 LASER/CCD PULSE RATE - 3

4
Keyboard Language
USA (Original setting) Italian
Norway France
Germany Vietnam
Sweden Spain
Denmark Portugal
Switzerland Hungary
*As a general rule, the following characters are not supported by the scanner for
countries other than United States:
@ | $ # { } [ ] = / ‘ \ < > ~

5
Symbologies On/Off - 1
CODE 11 - ENABLE CODE 11 CODE 11 - DISABLE
CODE 39 ENABLE CODE 39
CODE 39 DISABLE
FULL ASCII ENABLE FULL ASCII DISABLE

6
Symbologies On/Off - 2
CODE 93 - ENABLE
CODE 93
CODE 93 - DISABLE
CODE 128 - ENABLE CODE 128 CODE 128 - DISABLE
CODE 128 ISBT - ENABLE CODE 128 ISBT - DISABLE
CODABAR - ENABLE CODABAR
CODABAR - DISABLE
I2OF5 - ENABLE
INTERLEAVE
2 OF 5
I2OF5 - DISABLE
ID2OF5 - ENABLE INDUSTRIAL 2 OF 5
ID2OF5 - DISABLE

7
Symbologies On/Off - 3
MSI - ENABLE
MSI
MSI - DISABLE
UPC-A ENABLE UPC/EAN UPC-A DISABLE
UPC-E ENABLE UPC-E DISABLE
EAN-13 ENABLE
EAN-13 DISABLE
EAN-8 ENABLE
EAN-8 DISABLE

8
Symbologies Set Up - 1
CODE 11 ID CHARACTER – “m”
CODE 11
CODE 11 ID CHARACTER – “Z”
CODE 11 DOUBLE CHECK
ENABLE
CODE 11 DOUBLE CHECK
DISABLE
CODE 39 SS CHAR - NONE CODE 39 CODE 39 SS CHAR ‛+’
CODE 39 SEND START/STOP
CHARS ENABLE
CODE 39 SEND START/STOP
CHARS DISABLE
CODE 39 ID CHARACTER ‛a’ CODE 39 ID CHARACTER ‛Z’
CODE 39 DOUBLE CHECK
ENABLE
CODE 39 DOUBLE CHECK
DISABLE