SymmetryOffice Align 300 User manual

Align 300
Installation Ins tructions
INSTALLATION WARNINGS:
Read the entire instruction sheet before you begin ins t allation or assembly. Ins t aller must verify that the wall will safely
support the combined w eigh t of all the attached equipmen t and hardware. Improper ins t allation of this product can cause
extensive proper t y damage or serious personal injury, either during or aft er the ins t allation. It is the
responsibility of the ins t aller to ensure that all applications including wood, concr e t e , block, brick, s t eel, etc.
are secured properly to code. California Ins t allations could require specific anchorage, and additional
mounting screws. Check with local authorities for codes in y our
area. Other seismic s t at e s have similar r egulations .
DISCLAIMER: The Manufacturer and/ or Distributor
will bear no responsibility for an y damages of any
kind arising from any impr oper ins t allation of this
product. Because w all construction varies widely and
the ultimat e method of mounting is out of the
Manufacturers or Distributors c on t r ol, it is imperative
that the ins t aller consult with loc al engineering,
architectural, or construction per s onal to ensure the
wall moun t is constructed properly and to code t o handle
the applied lo ad.
Parts in B o x
Provided Tools Needed
5x
5x
#12 x 2-1/2
6x
V elcr o
T oggler
B olt s
5x
1 / 4 - 2 0 x 3
1x
Mous e
Hous e
1x
T r ack
Cove r
4x
M4 x 8mm
4x
M4 x 12mm
1x Quick
C onnect
Br ack e t
1/ 8 "
3 /16 "
154420180 Rev. A

Align 300
Installation Ins tructions
Slide k e ybo ar d as s embly
on to tr ack and tighten in
po sition with hand knob .
L o c a t e the wall s t ud and
mark the top hole .
Drill a pilo t hole and ins er t
screw part way. Place a level
on the side of moun t and
mark other hole s . Drill pilo t
holes. T igh t en all screws to
the w all.
1/ 8˝
NOTE: Refer t o instruction
shee t included with track
f or deatils on dif f ere n t w all
mounting conditions.
Remove the end cap at one
top of the tr ack slide r .
Slide LCD assembly on t o
track and tighten in position
with hand knob .
1/ 8˝
Affix the
mous e holder
to the underside
of the keyboard tr a y .
Replace end c ap and
tigh t en.
Using the s c re w s provided
and a Phillip s head
screwdriver, at t ach the
LCD to the Quick Connect
Br ack e t . Slide the
Quick Connect Br ack e t on to
the mounting plat e .
Affix the 6 Velcro
hook and loops to
the underside of
the k e ybo ar d.
Position and
press the k e ybo ar d
firmly on t o the k e ybo ar d tr a y .
*Release P oin t s
Adjusting the
Height Adjustable S egmen t :
1. With the monitor moun t ed t o the
arm, move the monit or through the
heigh t range; Ensure the arm will hold the
monitor in the position you plac ed it .
2. If the monitor drops or r ebounds upward,
adjust the tension screw at the back of the
arm segment as sho wn using the 3/16”
Allen key. Repeat s t ep s until the
monitor is c oun t erb alanc ed.
3. Repeat for keyboard tr a y c oun t erb alanc e .
3/16˝
Using the Height A djus t able
Cable Manager :
1. Remove cable manager by
pinching at r ele as e poin t s .
2. Lay cables in
c able manage r .
3. Snap c able manager
back in t o plac e .
No t e t e xt indic ation
“FRONT” inside
cable manage r .
4 . Repeat for keyboard tray c able manage r .