Synergy Global Technology LCDR7U15-01 User manual

1
Synergy Global Technology Inc
LCDR7U15-01
User Guide
Toll Free: 1-888-865-6888
Tel: [phone] Fax: [phone]
Email: [email protected]

2
INDEX
1. LCDR7U15-01
SPECIFICATION…..………………….01
2. LCDR7U15-01 PIN
DEFINATION……………….……02
3. LCDR7U15-01 Operation
Guide….…..…………..…….03
4. LCDR7U15-01 Function
Guide……………..……….….04
5. LCDR7U15-01
Dimension………………..………….….05
6. Safety Notes……………………….…………….….06

3
1. LCDR7U15-01 Specification
Specification
Module Size 331.6(H)×254.76(V) ×13.0(D)
Power Source DC12V
Size 15 INCH Color TFT
Resolution 1024(H)×768(V)
Pixel Pitch 0.297(H)×0.297(V)
Brightness 250 cd/㎡
Viewing angle 60/60/40/60 (L/R/T/B)
Operation
Temperature 0°C ~ 50°C
Storage
Temperature -20°C ~ 60°C
Input Terminal DSUB15PIN, BNC×1, RCA×1, S-Video×1
Output Terminal RCA×1
Input Signal
PC：VESA Mode 0.7Vp-p@750hm R,G,B,HS,VS
Video：1Vp-p@750hm
BNC NTSC：ƒH：15.75Khz PAL：ƒH：15.625Khz
RCA ƒV：60Hz ƒV：50Hz
S-Video
Output Signal 1.2Vp-p@750hm
Power
Consumption 25W(Max)
Weight 13 LBS
Control function OSD
Unit：mm

4
2. LCDR7U15-01 A/B BOARD PIN DEFINATION
J14 FOR OSD KEYBOARD CONNECTOR
J14 NAME DEFINITION
PIN 1 GND CONNECTOR TO GND
PIN 2 OSD KEY1 FOR KEYBOARD SCAN KEY1
PIN 3 OSD KEY2 FOR KEYBOARD SCAN KEY2
PIN 4 OSD KEY3 FOR KEYBOARD SCAN KEY3
PIN 5 OSD KEY4 FOR KEYBOARD SCAN KEY4
PIN 6 LED Y POWER LED YELLOW
PIN 7 +12V CONNECTOR TO DC+12V
PIN 8 OSD KEY5 FOR KEYBOARD SCAN KEY5
PIN 9 LED R POWER LED RED
PIN 10 GND CONNECTOR TO GND
J17 FOR INVERTER CONNECTOR
J17 NAME DEFINITION
PIN 1 ADJ BLACK LIGHT ADJ 0V=LOW ,5V=HIGH
PIN 2 GND CONNECTOR TO GND
PIN 3 +12V DC+12V FOR INVERTER POWER
PIN 4 GND CONNECTOR TO GND
PIN 5 ON/OFF BLACK LIGHT ON/OFF 0V=OFF,5V=ON
J18 FOR A/D BOARD POWER INPUT
J18 NAME DEFINITION
PIN 1 +12V DC+12V INPUT
PIN 2 GND GND

5
J19 (DC JACK) FOR A/D BOARD POWER INPUT
J19 NAME DEFINITION
PIN 1 +12V DC+12V INPUT
PIN 2 GND CONNECTOR GND
PIN 3 GND CONNECTOR GND
P1 (D-SUB) FOR VGA INPUT CONNECTOR
P1 NAME DEFINITION
PIN 1 RED VGA RED INPUT (0.7Vp-p)
PIN 2 GREEN VGA GREEN INPUT (0.7Vp-p)
PIN 3 BLUE VGA BLUE INPUT (0.7Vp-p)
PIN 4 NC NO CONNECTOR
PIN 5 GND DIGITAL GND
PIN 6 AGND ANALOG GND FOR RED
PIN 7 AGND ANALOG GND FOR GREEN
PIN 8 AGND ANALOG GND FOR BLUE
PIN 9 NC NO CONNECTOR
PIN 10 GND DIGITAL GND
PIN 11 NC NO CONNECTOR
PIN 12 DDC_SDA DDC SDA (TTL)
PIN 13 HSYNC HSYNC INPUT (TTL)
PIN 14 VSYNC VSYNC INPUT (TTL)
PIN 15 DDC_SCL DDC SCL (TTL)
CON3 (RCA) FOR VIDEO1 INPUT
CON3 NAME DEFINITION
PIN 1 VIDEO IN VIDEO INPUT (0.7Vp-p TO 1.0Vp-p)
PIN 2 GND CONNECTOR TO VIDEO GND
PIN 3 GND CONNECTOR TO VIDEO GND
PIN 4 GND CONNECTOR TO VIDEO GND
CON2 (RCA) FOR VIDEO2 INPUT
CON2 NAME DEFINITION

6
PIN 1 VIDEO IN VIDEO INPUT (0.7Vp-p TO 1.0Vp-p)
PIN 2 GND CONNECTOR TO VIDEO GND
PIN 3 GND CONNECTOR TO VIDEO GND
PIN 4 GND CONNECTOR TO VIDEO GND
CON4 (S-VIDEO) FOR VIDEO3 INPUT
CON4 NAME DEFINITION
PIN 1 GND
PIN 2 GND
PIN 3 Y LUMA INPUT (0.7Vp-p)
PIN 4 C CHROMA INPUT (0.7Vp-p)
CON1 (RCA) FOR VIDEO OUTPUT
CON1 NAME DEFINITION
PIN 1 VIDEO OUT VIDEO OUTPUT
PIN 2 GND CONNECTOR TO VIDEO GND
PIN 3 GND CONNECTOR TO VIDEO GND
PIN 4 GND CONNECTOR TO VIDEO GND
J11 TO PANEL CONNECTOR
J11 NAME DEFINITION
PIN 1 NC NO CONNECTOR
PIN 2 NC NO CONNECTOR
PIN 3 NC NO CONNECTOR
PIN 4 LCD VCC PANEL POWER
PIN 5 LCD VCC PANEL POWER
PIN 6 R0(ODD) TTL RED0(ODD)
PIN 7 R1(ODD) TTL RED1(ODD)
PIN 8 R2(ODD) TTL RED2(ODD)
PIN 9 R3(ODD) TTL RED3(ODD)
PIN 10 GND CONNECTOR GND
PIN 11 R4(ODD) TTL RED4(ODD)

7
PIN 12 R5(ODD) TTL RED5(ODD)
PIN 13 R6(ODD) TTL RED6(ODD)
PIN 14 R7(ODD) TTL RED7(ODD)
PIN 15 GND CONNECTOR GND
PIN 16 G0(ODD) TTL GREEN0(ODD)
PIN 17 G1(ODD) TTL GREEN1(ODD)
PIN 18 G2(ODD) TTL GREEN2(ODD)
PIN 19 G3(ODD) TTL GREEN3(ODD)
PIN 20 GND CONNECTOR GND
PIN 21 G4(ODD) TTL GREEN4(ODD)
PIN 22 G5(ODD) TTL GREEN5(ODD)
PIN 23 G6(ODD) TTL GREEN6(ODD)
PIN 24 G7(ODD) TTL GREEN7(ODD)
PIN 25 GND CONNECTOR GND
PIN 26 B0(ODD) TTL BLUE0(ODD)
PIN 27 B1(ODD) TTL BLUE1(ODD)
PIN 28 B2(ODD) TTL BLUE2(ODD)
PIN 29 B3(ODD) TTL BLUE3(ODD)
PIN 30 GND CONNECTOR GND
PIN 31 B4(ODD) TTL BLUE4(ODD)
PIN 32 B5(ODD) TTL BLUE5(ODD)
PIN 33 B6(ODD) TTL BLUE6(ODD)
PIN 34 B7(ODD) TTL BLUE7(ODD)
PIN 35 GND CONNECTOR GND
PIN 36 NC NO CONNECTOR
PIN 37 GND CONNECTOR GND
PIN 38 HSYNC TTL H-SYNC
PIN 39 GND CONNECTOR GND
PIN 40 VSYNC TTL V-SYNC
PIN 41 GND CONNECTOR GND
PIN 42 DE TTL DATA ENABLE
PIN 43 GND CONNECTOR GND
PIN 44 CLOCK TTL PANEL CLOCK
PIN 45 GND CONNECTOR GND
J16 TO PANEL CONNECTOR
J16 NAME DEFINITION

8
PIN 1 R0(EVEN) TTL RED0(EVEN)
PIN 2 R1(EVEN) TTL RED1(EVEN)
PIN 3 R2(EVEN) TTL RED2(EVEN)
PIN 4 R3(EVEN) TTL RED3(EVEN)
PIN 5 GND CONNECTOR GND
PIN 6 R4(EVEN) TTL RED4(EVEN)
PIN 7 R5(EVEN) TTL RED5(EVEN)
PIN 8 R6(EVEN) TTL RED6(EVEN)
PIN 9 R7(EVEN) TTL RED7(EVEN)
PIN 10 GND CONNECTOR GND
PIN 11 G0(EVEN) TTL GREEN0(EVEN)
PIN 12 G1(EVEN) TTL GREEN1(EVEN)
PIN 13 G2(EVEN) TTL GREEN2(EVEN)
PIN 14 G3(EVEN) TTL GREEN3(EVEN)
PIN 15 GND CONNECTOR GND
PIN 16 G4(EVEN) TTL GREEN4(EVEN)
PIN 17 G5(EVEN) TTL GREEN5(EVEN)
PIN 18 G6(EVEN) TTL GREEN6(EVEN)
PIN 19 G7(EVEN) TTL GREEN7(EVEN)
PIN 20 GND CONNECTOR GND
PIN 21 B0(EVEN) TTL BLUE0(EVEN)
PIN 22 B1(EVEN) TTL BLUE1(EVEN)
PIN 23 B2(EVEN) TTL BLUE2(EVEN)
PIN 24 B3(EVEN) TTL BLUE3(EVEN)
PIN 25 GND CONNECTOR GND
PIN 26 B4(EVEN) TTL BLUE4(EVEN)
PIN 27 B5(EVEN) TTL BLUE5(EVEN)
PIN 28 B6(EVEN) TTL BLUE6(EVEN)
PIN 29 B7(EVEN) TTL BLUE7(EVEN)
PIN 30 GND CONNECTOR GND
J5 LCD VCC SELECT
J5 NAME DEFINITION
PIN 1 +5V PIN 1 AND PIN2 SHART PANEL VCC =5V
PIN 2 PANEL VCC PANEL VCC OUTPUT
PIN 3 +3.3V PIN2 AND PIN3 SHART PANEL VCC=3.3V

9

10

11
3. LCDR7U15-01 Operation Guide
1. MENU: Press the Menu to enter Composite-Video/VIDEO1 Input.
Press MENU again to enter Composite-Video/VIDEO2 Input. Press
MENU again to enter Composite Video/VIDEO3.
2. SELECT: Press the SELECT to enter OSD Selection. OSD Select
offer varies setting selection. (Language, Brightness, Contrast,
Saturation, Hue, Sharpness and Reset)
3. UP: Press the UP to adjust the level setting.
4. DOWN: Press the DOWN to adjust the level setting.
5. BRIGHTNESS (UP): Press the BRIGHTNESS (UP) to increase the
brightness level.
6. BRIGHTNESS (DOWN): Press the BRIGHTNESS (DOWN) to
decrease the brightness level
7. CONTRAST (UP): Press the CONTRAST (UP) to increase the
contrast level.
8. CONTRAST (DOWN): Press the CONTRAST (DOWN) to
decrease the contrast level.
9. POWER: Press POWER to switch ON and OFF the LCD Monitor.
1. MENU
2. SELECT
3. UP
4. DOWN
5. BRIGHTNESS (UP)
6. BRIGHTNESS (DOWN)
7. CONTRAST (UP)
8. CONTRAST (DOWN)
9. POWER

12
PC Display Mode
4. LCDR7U15-01 Function Guide
PC OSD SELECT.
Press “MENU” Button，display will show following picture.
M O D E : 8 0 0 X 6 0 0
B A S I C S E T T I N G
P O S I T O N
S C R E E N S E T T I N G
A U T O A D J U S T
M E N U S E T T I N G
R E C A L L
A L L R E S E T
E X I T
H : 3 8 . 0 V : 6 0 . 5
Continue to press “UP” & “DOWN“ buttons and select above functions. Then, use
“Menu” button to enter these functions and adjust them to your personal preference.
BASIC SETTING : See1.1
POSITON : see1.2
SCREEN SETTING : See1.3
AUTO ADJUST : See 1.4
MENU SETTING : See1.5
RECALL : Adjust to last setting
ALL RESET : All Reset value
EXIT: exit
1-1 BASIC SETTING
M O D E : 8 0 0 X 6 0 0
B R I G H T N E S S 1 5
C O N T R A S T 1 1 2
C O L O R C O N T R O L
E X I T
H : 3 8 . 0 V : 6 0 . 5
BRIGHTNESS: Adjust LCD brightness level 0~15 of the image
CONTRAST: Adjust white color level 0~255 of the image
PC Input Frequency

13
COLOR CONTROL:
M O D E : 8 0 0 X 6 0 0
C O L O R 1
C O L O R 2
C O L O R 3
U S E R
E X I T
H : 3 8 . 0 V : 6 0 . 5
COLOR 1 : Set color to 9300K（Use “MENU” to enter）
COLOR 2: Set color to 7500K（Use “MENU” to enter）
COLOR 3: Set color to 6550K（Use “MENU” to enter）
USER : Set color by user（Use “MENU” to enter）；
EXIT : Back to new setting.
1-2 POSITON
M O D E : 8 0 0 X 6 0 0
P H A S E 1 2
H - S I Z E 3 1
H - P O S I T I O N 3 2
V - P O S I T I O N 2 0
E X I T
H : 3 8 . 0 V : 6 0 . 5
PHASE: Adjust phase level 0~31 of the image
H-SIZE : Adjust size of the image
H-POSITION: Adjust UP/ DOWN/ HOR/VER position of the image.
V-POSITION : Adjust OSD UP/ DOWN/ HOR/VER position of the image.
EXIT : Back to new setting.
1-3 SCREEN SETTING
M O D E : 8 0 0 X 6 0 0
G R A P H I C / T E X T
E X P A N S I O N
S M A R T S C A L E
S H A R P N E S S 7
E X I T
H : 3 8 . 0 V : 6 0 . 5
GRAPHIC/TEXT: DOS MODE/ change Text 720x400 & Gfx 640x40
SHARPNESS : Adjust Sharpness level 0~19 of the image
EXIT : Back to new setting.

14
1-4 AUTO ADJUST
M O D E : 8 0 0 X 6 0 0
A U T O T U N E
A U T O T R A C K I N G
A U T O P O S I T I O N
E X I T
H : 3 8 . 0 V : 6 0 . 5
AUTO TUNE : Auto tracking , positioning, phase and size (press “MENU” to enter this adjustment.
It takes 5 second to finish this adjustment.)
1-5 MENU SETTING
M O D E : 8 0 0 X 6 0 0
L A N G N A G E
M E N U P O S I T I O N
F W V E R S I O N
E X I T
H : 3 8 . 0 V : 6 0 . 5
LANGUAGE:
M O D E : 8 0 0 X 6 0 0
E N G L I S H
J A P A N E S E
E X I T
H : 3 8 . 0 V : 6 0 . 5
OSD LANGUAGE selecting English & JAPANESE only!
MENU POSITION: just OSD UP/ DOWN/ HOR/VER position of the image.
FW VERSION: Display Bios Version
EXIT : Back to new setting.

15
OSD SELECT
LANGUAGE:
Language Selection: (English, Chinese
and Japanese)
BRIGHTNESS:
Brightness Adjustment: Adjust LCD
Backlight (Level 0~15)
CONTRAST:
Contrast Adjustment: Adjust White
Balance (Level 0~255)
SATURATION:
Saturation Adjustment: Adjust Color
Saturation (Level 0~127)
VIDEO 1
CONTRAST 150
VIDEO 1
BRIGHTNESS 15
VIDEO 1
LANGUAGE
VIDEO 1
SATURATION 64

16
HUE:
Hue Adjustment: Adjust Color Hue
(Level 0~255)
SHARPNESS:
Sharpness Adjustment: Adjust Sharpness
(Level 0~15)
RESET:
Return to Operation Manual.
VIDEO 1
HUE 112
VIDEO 1
SHARPNESS 7
VIDEO 1
RESET

17
5. LCDR7U15-01 Dimension
59.5
310
300
M4x0.7(Stud)High10mmPground terminal
306.6
483
88.2
Unit：mm

18
6. Safety Notes
1. Do not apply pressure to the LCD screen.
2. Do not sprinkle any liquid to clean the LCD. If you
need to clean it, please use a LCD cleaning cloth.
3. Please do not use any accessory not provided by the
manufacturer.
4. Please do not operate or store in the high temperature.
(Operating 0~60 ْ◌C, Storage 0~80 ْ◌C)
5. When you connect the power cable, please ensure the
Anode (Positive) and Cathode (Negative) is connected
correctly. If connected incorrectly, it might damage the
LCD.
6. Please be caution and handle the system with care
during moving.