Syris MDNET-5W User manual

MDNET-5W
Wi-Fi/Ethernet/RS485 Converter
Operation Manual
Version 01.00
2016/03/24

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
1
I. Features & Specification
Features:
Connect RS485 devices to Ethernet or Wi-Fi network
Connect Ethernet device to Wi-Fi network
Multi-Controller connection
Remote firmware upgradable
Specification:
Convert mode
Ethernet ←→ RS485
Wi-Fi ←→ RS485
Ethernet ←→ Wi-Fi
Interface Wi-Fi / Ethernet / RS485
Wi-Fi 802.11 b/g/n
Ethernet 10/100BaseT, RJ45 connector
Operating Mode TCP Server, TCP Client, UDP
Connector port 4 PIN (RS485 + DC power)
RS485 Baud Rate 300 ~ 115,200 bps
Parity None/ Even/ Odd
Data bits 8 / 7
Stop bits 1 / 2
Configuration tool Web Browser, Windows utility.
Reset function Initial button
Status Indicator 4 LED
Operating Temperature -20°C ~ 70°C
Power 8V ~ 15V DC / 1W ~ 2W
Size(mm) 77W x 59H x 22.5D

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
2
II. Wiring Diagram

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
3
III. Network Parameters Setting
1. Execute “NET_Discover_V0110.exe” and press to search MDNET-5W product.
2. Factory default IP is “192.168.1.101”. User can check the MAC address from product sticker with IP
to confirm the device.

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
4
3. Double click IP (192.168.1.101) to open the web configure page(http://192.168.1.101)
Default login ID / Password : admin / admin

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
5
4. Default Net Mode is the same as the following. User can modify Net Mode and other parameters. If
device cannot communicate properly after setting, user can reset MDNET-5W with initial button.
Communication Parameters Factory Default
Serial Configure 230400,8,n,1
Serial Framing Length 1050
Locale/Remote Port Number 5001

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
6
IV.Ethernet / RS485 converter (Default)
1. Network module setting:
Default Ethernet (DHCP) +Wi-Fi AP mode
ETH-SERIAL Ethernet only (Factory Default)
WIFI(CLIENT)-SERIAL Wi-Fi client mode
WIFI(AP)-SERIAL Wi-Fi AP mode
ETH-SERIAL：Factory default is ETH-SERIAL.
When user modify the IP and click on Apply button, device will reboot and apply the setting after 30
seconds.
2. Initial button:
Press initial button 15 seconds until Link status (Ethernet) LED blinking.
Wait 2 minutes, MDNET-5W will reset to factory default.

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
7
3. RS485 baud rate setting
Execute V7 tools to connect MDNET-5W with correct IP and port.
Click Get S/N, and select “COMM.” Tab to configure RS485 parameters.

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
8
V. Wi-Fi / RS485 converter
1. Execute “NET_Discover_V0110.exe” and press to search MDNET-5W product.
2. Factory default IP is “192.168.1.101”. User can check the MAC address from product sticker with IP
to confirm the device.

MDNET-5W Wi-Fi/Ethernet/RS485 Converter Operation Manual
9
3. Double click IP (192.168.1.101) to open the web configure page(http://192.168.1.101)
Default login ID / Password : admin / admin
4. Change net mode to “Default” to enable Wi-Fi scan function.
5. Execute “NET_Discover_V0110.exe” to search MDNET-5W again.