Syris SYKD2N-H1 User manual

SYKD2N-H1
SYRISTCP/IPOLEDDisplayReader
Operation Manual
Version 01.05
2021/09/24

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
1
I. Features & Specification
Feature:
lMulti-mode access control
lSupport ISO15693/ ISO14443A(Mifare)/ ISO14443B/ DESFire/ NTAG203
l2.42 inch OLEDDisplay
lMulticommunication interface
lProvide protocolto develop.
Specification:
Frequency 13.56MHz
Interface RS485 / Wiegand / Ethernet / Wi-Fi
Wiegand Wiegand (support 26/32/34/35/37/42/66bits)
RS485 baudrate 19,200 bits/sec(4,800~460,800)
Ethernet 10M/100M Ethernet Port
Wi-Fi 802.11 b/g/n
Display 2.42 inch128x64 OLEDdisplay
StatusIndicator TricolorLED(RGB)&Beeper
Keypad 13 capacitivetouchbutton
IRSensor 1IRsensorforwavinghandto access door(adjustablerange 0~10cm)
DigitalInput Upto 3
(1DI+2no-voltage DIsharethesameportwith Wiegand)
DigitalOutput Up to 4
(2 Relayoutput+2open collectorDOshare the same portwith
Wiegand)
HFProtocols ISO15693 / ISO14443A/ ISO14443B/ DESFire /NTAG203
HFReadrange Up to 5 cm
ID 0001~9999
NumberofCards 10000
CapacityofRecords 100000
PowerSupply 9 ~28 VDC (12 VDC)
Powerconsumption 1W~6W
Operating temperature -10 C to 60 C
Dimensions(mm) 124 x90 x27mm

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
2
II. Wiring Diagram

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
3
III. Network ParameterSetting
1. Execute “NET_Discover_V0110.exe”and press to search SYRISseriesproduct.
2. FactorydefaultIPis “192.168.1.101”.Usercan checkthe MACaddress fromproduct stickerwithIP
to confirmthe device.

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
4
3. Double clickIP(192.168.1.101)toopen the web configure page(http://192.168.1.101)
DefaultloginID /Password:admin/ admin

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
5
4. Default Net Mode isthe same asthe following. Usercan modifyNet Mode and otherparameters. If
device cannot communicate properlyaftersetting,usercan reset NETmoduleviaMicro USB.
Communication Parameter FactoryDefault
SerialConfigure 230400,8,n,1
SerialFraming Length 1050
Locale/Remote Port Number 5001

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
6
IV. Network Mode Switch
SYRISdevice support4 networkmodes: Default ETH(Ethernet) Wi-Fi(STA)
Default Ethernet (DHCP)+Wi-FiAP mode
ETH Ethernetonly
WIFI(STA) Wi-Ficlient mode
1. ETH Factorydefaultis ETH-SERIAL. (StandardTCP/IPReader)
When usermodifythe IPand clickon Applybutton,devicewill reboot and applythe settingafter30
seconds.

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
7
2. WIFI(STA)：SYRIScanbe set to communicate viaWireless APwithout Ethernet.
STASSID: Enterthe SSIDfromAP youwillconnect tonetwork.
Scan : Usercan scan AP in range ofdeviceand select oneto connect. Butusercannot scan the
AP afterchanging defaultnetworkmode (Ethernet only)to Wi-Fi(Client). Device need to poweroff /
on toenable the scan function.
STAEncType : SelectEncrypt type forAP connection.
Password: EnterpasswordforAP.
IPType: DHCPisdefaultmode. Ifuserhaveto setupa staticIP,please selectStatic.
PS:Wi-Fi MAC addressisEthernetMACsubtract1.
Ex. EthernetMAC :AC:A2:13:B5:5A:B5，Wi-Fi MAC :AC:A2:13:B5:5A:B4

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
8
3. Default mode：Ethernet (DHCP)+Wi-FiAP mode.
It’sDual-Mode (Ethernetand Wi-FiAP，but Ethernet onlysupport DHCP.)

SYKD2NTCP/IPOLEDDisplayReaderOperation Manual
9
APSSID: Setup device’sSSID.
APPasswd: Device’sWi-Fipassword. (Defaultis12345678)