SYSTEM Electronics COPILOT 15 User manual

system-electronics.it
USER MANUAL
COPILOT 15”
Monitor
INDUSTRIAL PC
Order Code: 2E000xxx
Date: 06/2018 - Rev: 1.0
Summary
1. Generalities........................................3
2. Technical characteristics.................................................3
3.Connections..............................................3
4. Touch-Screen: Operation and calibration.........4
4.1 Calibration........................................4
4.2 Default setting of touch parameters....5
5. Energy saving and LED signalling...................5
6.Accessories.................................................5
7.Waste Directive.................................................6

pag. 2
COPILOT 15" Monitor
Order Code 2E000xxxJune 2018 - Rev. 1.0
Revision History Pages
Rev. 1.0 Drafting 6
SYSTEM CERAMICS s.p.a. Div. Electronics
via Ghiarola Vecchia, 73
41042 Fiorano (MO) - Italy
tel. [phone] - fax [phone]
www.system-group.it
e-mail: [email protected]
This product meets the EMC protection
requirements of Directive 2014/30 /
EC (ex 89/336 / EEC) and subsequent
amendments.
SYSTEM Ceramics S.p.A - Div. Electronics reserves
the right to make changes of any kind to the technical
specications at any time and without notice. The in-
formation contained in this documentation is believed
to be correct and reliable. The reproduction, even if
partial, of the content of this catalog, is allowed only
with the authorization of SYSTEM Ceramics S.p.A.
Div. Electronics.

pag. 3
COPILOT 15" Monitor
Order Code 2E000xxxJune 2018 - Rev. 1.0
Emergency Mushroom
M12 Female 5-pole A
• 1 Mushroom Emergency n.c. #1
• 2 Mushroom Emergency n.c. #2
• 3 Mushroom Emergency n.c. #1
• 4 Mushroom Emergency n.c. #2
• 5 n.c.
NOTE
The emergency button operates internally on two sepa-
rate circuits, connected to the M12 connector on contacts
1-3 and 2-4 respectively.
Figure 3.3 External connector view
USB Port [TYPE-A]
• 1 5V_USB
• 2 D-
• 3 D+
• 4 GND_USB
Figure 3.4
24V Power Supply
M12 Female 5-pole A
• 1 +24V
• 2 n.c.
• 3 GND
• 4 n.c.
• 5 PE
Figure 3.2 Vista del connettore esterno
1. Generalities
The COPILOT 15" Monitor is an industrial monitor with
integrated touch-screen. It is housed in a compact and
robust IP65 enclosure, suitable for mounting on board
the machine.
2.Technical
characteristics
• Display TFT 15" high contrast, XGA 1024×768
• VGA input
• Touch-screen resistive with USB interface
• Power supply single 24Vdc
• Consumption 1A
• Working temperature: 0 ÷ 50 °C
• Realization IP65
• Dimensions: 385(W)×315(H)×85(D)
• Weight 4.1Kg
• Fixing vesa 100mm
• Supported modes: 640×480@60Hz
640×480@72Hz
640×480@75Hz
720×400@70Hz
800×600@60Hz
800×600@72Hz
800×600@75Hz
1024×768@60Hz
1024×768@70Hz
1024×768@75Hz
3. Connections
Figure 3.1 shows the screen printing of the rear panel
of the Monitor.
Figure 3.1
1
45
3
2
1
45
3
2
Pulsante ADJ
The ADJ button allows you to resynchronize the image
with the incoming VGA signal to correct delays in signal
propagation.

pag. 4
COPILOT 15" Monitor
Order Code 2E000xxxJune 2018 - Rev. 1.0
External VGA connector
It is necessary to use an external wiring that has the IP65
characteristics on the VGA port to achieve the maximum
degree of waterproong.
Pinout:
• 1 RED
• 2 GREEN
• 3 BLUE
• 4 NC
• 5 GND
• 6 GND-RED
• 7GND-GREEN
• 8 GND-BLUE
• 9 5V
• 10 GND-SYNC
• 11 GND
• 12 DDC DATA
• 13 HSYNC
• 14 VSYNC
• 15 DDC CLOCK
operation and calibration
The Copilot 15'' Monitor has an innovative ca-
pacitive backward-projected touch screen (PCAP)
with 10 possible touches at the same time.
System Electronics can provide dierent settings to co-
ver the dierent needs of the operator interface: from
operation with gloves or in dirty environments to the
optimization in the precision of touch, up to the natu-
ralness of gestures with Windows (rotation, movement
and zoom with the hand).
The 15" Copilot Monitor is supplied already calibrated
and equipped with a setting that typically covers all
needs without penalizing any of them: however, there
are commands to customize the behavior according to
the specic application.
4.1 Touch-screen calibration:
The Copilot 15" Monitor does not normally require
calibration procedures, as it is already optimized during
production.
If there is a need to optimize the calibration of the tou-
ch-screen follow the procedure below.
4. Touch-screen:
In the Tablet PC Settings section, press the "CALIBRATE"
button:
To test the calibration of the touch screen, touch the
crosshairs each time they appear on the screen with
one nger.
Click at random on the screen to return to the last ca-
libration.
Press ESC to exit.
Do not change the orientation of the monitor before
completing the calibration process.

pag. 5
COPILOT 15" Monitor
Order Code 2E000xxxJune 2018 - Rev. 1.0
4.2 Default settings of the touch
parameters:
To reset the factory settings again, select the "RESET"
button from the TABLET PC SETTING window:
NOTE
The Copilot 15'' Monitor does not require specic dri-
vers; native Windows drivers are used for touch-screen
operation
5. Energy saving and
front LED signaling
The front LED on the 15" monitor indicates the status of
the power supply and correct signal reception.
With insucient power supply for correct operation
the front LED is o.
The GREEN color of the front LED indicates correct
operation.
In the absence of a correct VGA signal or with an
unsupported resolution the monitor briey displays
the message "NO SIGNAL" and the front LED turns
RED. If the VGA cable is correctly connected, the
image will be displayed again and will automatically
adjust.
If there is no signal, the display uses a standby
mode, also indicated by the RED front LED.
There is no on/o button in the monitor.
Turn o the external power before connecting or
disconnecting the VGA cable
6. Accessories:
Desk support
Figure 5.1 Desk support - cod. E8330205100
280
220
260
n6.5 n°4 hole
s
Figure 5.2 Drilling jig

pag. 6
COPILOT 15" Monitor
Order Code 2E000xxxJune 2018 - Rev. 1.0
7.Waste Electrical
and Electronic
Equipment (WEEE)
andUseofHazardous
Substances
(RoHS) Directive
Information to users pursuant to Legislative Decree
14 March 2014, n. 49 "Implementation of Directive
2012/19/EU on waste electrical and electronic equip-
ment (WEEE).
Decree 25 July 2014 of the Ministry of the Environ-
ment, on "Implementation of the delegated directives
of the European Commission 2014/69/EU, 2014/70/EU,
2014/71/EU, 2014/72/EU, 2014/73/EU, 2014/74/EU,
2014/75/EU, 2014/76/EU of 13 March 2014 amending
Decree no. 27 of 4 March 2014 on the restriction of
certain hazardous substances in electrical and electronic
equipment (RoHS)".
The crossed-out wheeled bin symbol on the equipment
or on its packaging indicates that the product at the
end of its useful life must be collected separately from
other waste.
The separate collection of this equipment
at the end of its life is organized and managed by the
producer.
The user who will want to dispose of this equipment
you should then contact the manufacturer and follow
the system
that this has adopted to allow the separate collection of
equipment that has reached the end of its life.
Adequate separate collection for the subsequent start-up
of the discarded equipment to recycling, treatment and
environmentally compatible disposal
helps to avoid possible negative eects on the envi-
ronment and health and promotes the reuse and/or
recycling of the materials of which the equipment is
composed.
The abusive disposal of the product by the holder in-
volves the application of the administrative sanctions
provided for by current legislation.