SystemBase sWiFi/all User manual

U
ser Manual
www.sysbas.com
sWiFi
/all
Version 1.0 2020/0
8
/
15

1
Revision History
Revision Date Document Ver. Pages Revised Revised/Added/Removed Details of Revision
2020.08.15 1.0 All - New

sWiFi/all User Manual
2
Contents
1. WIFI TECHNOLOGY ...............................................................................................................4
2. COMPONENTS .......................................................................................................................5
3. PRODUCT ................................................................................................................................6
4. FEATURE ..................................................................................................................................8
5. HOW TO APPLY .....................................................................................................................9
6. GET STARTED ...................................................................................................................... 11
7. SETTINGS ............................................................................................................................. 12
APPENDIX ……………………………………………………………………………………………… 25
1. Specification ……………………………………………………………………………………25
2. Dimension ……………………………………………………………………………………… 26
3. Serial Port Pin Specification …………………………………………………………… 27
4. Setup Utility ………………………………………………………………………………… 28
5. Certification …………………………………………………………………………………… 34
Copyright ……………………………………………………………………………………… 34

sWiFi/all User Manual
3
Please be sure to read this manual before using and use the product safely and accurately.
• Pictures and photos in the manual may be different from the physical, and the document is subject to
change without notice to improve performance. For the last information, please visit our website
(www.sysbas.com).
• To view frequently asked questions and answers, please visit our website and find Support –Technical Support
–FAQ section.
• Documents can be downloaded from the product page or Download section.
• Sellers or users should be aware of the fact that this device is intended for industrial use(Class A), not for
residential use.
• This device has a potential for radio interference during use and may receive harmful interference from
other devices.
• Warranty policy is included in the product packaging.
• The exchange/return of the device can be handled by the procedure described in the Warranty Policy.

sWiFi/all User Manual
4
1. WiFi Technology
WiFi(Wireless Fidelity) is any “Wireless Local Area Network(WLAN)” product based on IEEE(Institute of Electrical
and Electronics Engineers) 802.11 standard, mainly using 2.4GHz and 5GHz frequency radio band.
WiFi-compatible devices use the technology to communicate wirelessly with each other over the WLAN network
and wireless access points, enabling them to reach approximately 100 meters indoors and further outdoors.
WiFi saves time and money by eliminating the need to lay cables.
It also supports encryption modes for wireless communication security such as Open, WEP, WPA-PSK, WPA2-PSK,
WPA-Enterprise WPA2-Enterprise and so on.
Benefits that users can gain from using WiFi technology are:
• Wireless communication(Up to 100m Indoor) with low installation cost
• Simple access procedures for quick installation and application
• Secure through encrypted communication

sWiFi/all User Manual
5
2. Components
Components Ordering Information
sWiFi/all, Dipole Antenna (Dual band),
5V 1A DC Adaptor
sWiFi/all

sWiFi/all User Manual
6
3. Product
LED
 RDY (Yellow): When in standby mode, LED flashes every 1.0 seconds.
When in setup mode, LED flashes every 0.4 seconds.
When in Infrastructure mode, turns on when the connection to AP is successful.
When in Soft AP mode, turns on when the connection is successful at Client.

sWiFi/all User Manual
7
 TXD (Green): Flashes when serial data is sent, turns off if there is no transmission.
 RXD (Red): Flashes when serial data is received, turns off if there is no reception.
Connector
DC Adapter, WiFi Antenna Connector(Male) Serial Port(RS232/422/485)
 PWR: Connect 5V 1A DC adapter included in the package
(internal diameter 3.47mm, outer diameter 1.33mm)
 WiFi Antenna Connector(Male): Connect the Antenna included in the package
 Serial Port(RS232/RS422/RS485): Serial ports which can communicate
(Please refer to the Appendix for pin specifications)
Button
 Press RST buttons for less than 3 seconds: Enter equipment setup mode
(Please refer to Ch.6 Getting Started for settings)
 Press RST buttons for more than 3 seconds: Initialize Equipment to factory settings
(Please refer to Appendix for initialized value)

sWiFi/all User Manual
8
4. Feature
sWiFi/all is a converter that converts wired serial communication to wireless WiFi communication and performs
the following functions.
1) Converts serial signals to wireless
Converts RS232/RS422/RS485 serial signals which requires cable installation to wireless WiFi signals.
2) Supports Various WiFi wireless communication
Supports WiFi wireless communication at low price.
Supports IEEE 802.11 a/b/g/n, Dual Band(2.4GHz/5GHz), Infrastructure/Soft AP functions, encryption functions
(Open, WEP, WPA-PSK, WPA2-PSK, Enterprise).
3) Low Power Running Mode
rLory is a low-power product powered by 5V DC and 2W power consumption. If it is difficult to supply power at
all times in the field, it is possible to operate by supplying power using solar panels and batteries.
4) VCP(Virtual Com Port)
Among the utilities provided, the VCP(Virtual Com Port) “ComRedirector” allows users to use the serial port on
sWiFi/all connected to the same network as if it is a serial port mounted on a PC.
It also supports Server/Client mode that can access serial socket.
Utility “sWiFiConfig” allows quick and easy set ups from user perspective.

sWiFi/all User Manual
9
5. How to Apply
Device/PC – AP – Device Connection (Infrastructure)
In Infrastructure mode, sWiFi/all performs connection between ComRedirector, TCP Server/Client and UDP via AP.
For sWiFi/all to access AP, the IP of the router band can be set to static IP which is a fixed IP, or set as DHCP
which the IP is assigned.
Each sWiFi/all can be connected to an AP wired PC or laptop to communicate.
For communication, each sWiFi/all can be connected to an AP-wired PC, or sWiFi/alls can be connected as
Server/Client each other.