TableCraft CW40196 User manual
InstruconManualVersion03042014 1
Instruction Manual
Commercial Built In Induction Cooker
CW40196 1800W / 120V 60HZ
/ 15 A
InstruconManualVersion03042014 2
Model No: CW40196
Power Rate: 1800W
Voltage: 120V / 60Hz
Temperature: 140°F - 440°F
Item Specifications:
Safety Precautions:
This manual contains safety precautions which are explained
below. To ensure safe operation of the unit, please carefully
read and follow this instruction manual.
These precautions should be followed at all times. Failure to
follow these precautions could result in injury to yourself and
others.
Connect the unit to a grounded power socket with appropriate voltage (120V ~ 60Hz). Do not connect other electrical appliances
to the same socket.
Make sure that the main installation is providing enough power to run the appliance (see the rating plate of the appliance to
verify).
Even though studies have shown that induction cookers will not effect pacemakers, as a precaution, people with pacemakers
should stand 12” (30cm) back from an operating unit.
Keep all credit cards, drivers licenses and other items with a magnetic strip away from an operating unit. The unit’s magnetic field
will damage the information on these strips.
The heating surface is made of strong, non-porous material. However, should the surface crack or break, stop using immediately
and unplug the unit. DO NOT OPERATE THE UNIT IF IT HAS BEEN DAMAGED OR IS MALFUNCTIONING IN ANY WAY!
Keep unit and power cord away from open flames, electric burners, excessive heat or sharp objects.
Do not place any objects inside the air intake or exhaust panels.
Do not place the unit directly next to a wall or under a cabinet. Do not block the air supply and ventilation of the appliance.
Do not place the unit directly next to or near any flammable objects.
Do not place empty cookware on the unit.
Do not leave an operating unit unattended.
After use of the unit, turn the unit OFF, unplug the unit and allow it too cool down completely before cleaning.
Always make sure to unplug the unit when it is not in use.
Important Reminders:
BEFORE FIRST USE:
Carefully remove unit from packaging.
Thoroughly inspect unit to ensure that the unit is in good condition.
Unit should be cleaned before first use. Carefully clean the surface with a clean, damp cloth (see “Cleaning Instruction” for more
detailed directions).
NEVER use abrasive cleaners or pads.
NEVER submerse the unit in water or wash the unit in the dishwasher.
NEVER spray controls or outside of unit with liquids or cleaning agents!
WARNING! DO NOT TOUCH COOKWARE, HEATING SURFACE, FOOD OR LIQUID WHILE THE UNIT IS IN OPERATION!
WARNING! ALWAYS MAKE SURE THAT THE UNIT IS OUT OF REACH FOR CHILDREN!
WARNING
Warning is used to indicate the presence of a hazard that
can cause severe personal injury, death, or substantial
property damage if the warning is ignored.
NOTE
Note is used to notify the reader of any installation, opera-
tion, or maintenance information that is important or
useful but not hazard related.
Includes:
Commercial Induction Plate
Remote Control
Instruction Manual
TableCraft Products
Amps:
15 A
InstruconManualVersion03042014 3
This unit is intended to be used with induction-ready cookware.
INDUCTION READY COOKWARE:
Ferrous Stainless Steel
Iron
Cast Iron
UNSUITABLE COOKWARE:
Pottery
Glass
Aluminum
Bronze
Copper
Cookware with Feet
Installation:
Place the unit on a flat, heat resistant surface.
The unit is NOT designed to be enclosed or built into an
area.
There must be a minimum or 4” (10 cm) of space between
the rear of the unit and any surrounding surface.
There must be 3/4” (2 cm) of space between the bottom of
the unit and any surrounding surface.
DO NOT BLOCK THE AIRFLOW OF THE UNIT!
There must be a minimum of 4” (10 cm) between the induction
range and any surrounding surface to allow sufficient airflow
around the unit. Blocking the airflow potentially overheat the
unit.
COUNTERTOP:
1. Place the unit on a flat, heat resistant surface.
2. Plug the power cord into a grounded electrical outlet with
the appropriate voltage level. Make sure that the unit is
the only appliance plugged into the electrical outlet.
Incorrect voltage levels will damage the unit. Incorrect
voltage, modification to the power cord or electrical
components will void the warranty.
DROP-IN
1. Choose a flat, heat resistant countertop for the mounting
surface.
2. Measure the area of the cutout, including the countersink
area. The depth of the surface around the cutout must be
reduced to allow for the countersink (see Example A).
NOTE
Exposed wood or particle board edges must be sealed with an
appropriate waterproofing material. Seal the edge between the
glass and the countertop with silicone or similar material.
Failure to do so may result in damage to the countertop.
3. Seal the joint between the induction warmer and
countertop.
4. Plug the power cord into a grounded electrical outlet with
the appropriate voltage level listed on the unit.
Functionality and Purpose:
Front View (while the cooker is in the cutout of the countertop)
TableCraft Products
A
B
C
Length
Width
Height
Lengthof
Cutout(Lipto
BaseDepth)
Cutout Dimensions:
D
A
B
C
D
13 in (33.02cm)
B = 12 in (30.48cm)
C = 0.65 in (1.651cm) Distance between the surface of unit and the countertop
D = 0.125 in (0.635cm) Between either side of the surface and the cutout
Unit
Inches
cm
Length Width Height (with feet) Lip to Base
Depth
12.625 12.4875 4 0.537
32.0675 31.72 10.16 1.364
Countertop
Surface Thickness
0.24
0.6096
Cord
Countertop
Cord
Countertop
Remote
Surface
Base
Length Width Height (w/o knob)
Lip to Base Depth
6.6 in 3.23 in 0.052 in 0.45 in
5.65 in 2.6 in 1.5 in N/A
Surface Thickness = 0.052 inches
Remote Cutout Instructions:
12
InstruconManualVersion03042014 4
Operation:
WARNING! Never leave the appliance unattended while
it is in operation.
NOTE
DO NOT PREHEAT EMPTY COOKWARE. The advantages of
induction cooking are speed and efficiency of the distribution of
heat. There is no need for pre-heating.
OPERATING THE DEVICE:
NOTE
The Power Levels range from 1-20 (P symbol).
The Temperature ranges from 140-440°F (°F symbol) increments
of 20.
1. Before plugging in the unit, be sure that you are using
induction ready cookware and you have already placed the
food inside the cookware. Place the cookware on the center of
the cooking surface - an error code will appear if you do not do
so.
2. Insert the plug into a suitable socket. You will hear acoustic
signals. The LED Display Panel will read, “8888” and then will
automatically switch to Standby Mode.
3. Rotate the ON/OFF knob to turn on the unit (the knob will click
when the unit is ON). A short acoustic signal will notify you that
the unit is ON.
4. Select the desired Temperature or Power Level (based on the
Mode that you have chosen) by rotating the ON/OFF knob.
The Control Lamp will indicate which mode is in use.
5. ALWAYS remember to turn the unit OFF and unplug when not
in use!
6. Do NOT put empty cookware on the cooking surface or leave
the cookware on the surface too long.
WARNING
WARNING
Electrical Shock Hazard
Keep water and other liquids from entering the inside
of the unit. Liquid inside the unit could cause an
electrical shock.
If liquid spills or boils over onto the unit, immediately unplug the unit and
remove cookware. Wipe up any liquid with a padded cloth.
Burn Hazard
Do not touch cookware, heating surface, food or
liquid while heating.
Hot foods and liquids can burn skin. Induction heating surfaces heat very
rapidly. Use caution when adding pre-heated oil, liquid or other food
already in the cookware.
1 = ON/OFF Knob - Rotating the ON/OFF knob clockwise increases the
temperature, while rotating the knob counterclockwise will decrease the
temperature (adjustable temperature: 140-440°F).
2 = POWER/TEMPERATURE button - Press to change the display panel from
power to temperature.
3 = LED Display Panel - This displays the power level, temperature, timer time
or error codes.
4 = CONTROL LAMP - Lights up to indicate which mode of adjustment is in
use (POWER/TEMPERATURE).
TableCraft Products
ERROR CODES:
E0 = There is no cookware on the cooking surface, or the
cookware is not induction ready. Unit will automatically turn
OFF.
E1 = The cookware is too hot and has overheated the
surface of the unit. In this case, unplug the unit and let it
cool down completely. When an error code of E2 is
displayed, the whole unit including the temperature con-
trols will be locked. After 20 minutes, the code will disap-
pear and the unit goes into Standby Mode.
E2 = The temperature sensors have overheated - surface
temperature is too high. The unit will stop heating and the
unit will cool itself down.
E3 = The automatic voltage protection has been activated.
This will happen if there is a voltage malfunction. As soon
as the current is stable, the error code will disappear and
the unit will resume normal functionality.
NOTE
For added precaution, if you receive error codes E1-E3,
unplug the unit immediately and let it cool down
completely.
InstruconManualVersion03042014 5
TableCraft Products
Cleaning, Maintenance and Storage:
NEVER submerse the unit or cord into water
NEVER put the unit or cord in the dishwasher
ALWAYS handle the unit with care
ALWAYS make sure to clean the unit after every use to
remove food residue
Use a slightly damp cloth to clean the glass surface
To avoid damaging the surface of the unit, never use
abrasive cleaners or cleaning supplies
To avoid damage to the plastic parts and control panel,
do not use any oil products to clean the unit
Do not use flammable, acidic, or alkaline materials or
substances near the unit
Do not use hard or sharp objects while cleaning the unit
Make sure that the bottom of the cookware in use does
not scrape across the glass surface
Never pull the unit by its cord
Make sure to store the unit on a dry, clean and flat
surface and out of reach of children
WARNING
Electrical Shock Hazard
Keep water and other liquids from entering the inside
of the unit. Liquid inside the unit could cause an
electrical shock.
If liquid spills or boils over onto the unit, immediately unplug the unit and
remove cookware. Wipe up any liquid with a padded cloth.
Burn Hazard
Do not touch cookware, heating surface, food or
liquid while heating.
Hot foods and liquids can burn skin. Induction heating surfaces heat very
rapidly. Use caution when adding pre-heated oil, liquid or other food
already in the cookware.
WARNING
NOTE
Do not attempt to clean the unit until it has completely cooled
down and is unplugged. Move unit away from an electrical
outlets.
Technical Data:
Model No: CW40196
Power Rate: 1800W
Voltage: 120V / 60Hz
Temperature: 140°F - 440°F
This appliance is tested according to ETL/FCC regulations.
Disposal:
Notice for Environmental Disposal: If in the future you should
need to dispose of your induction cooker, please note that
the unit should not be disposed of as household waste.
The symbol below on the unit’s packaging indicates that it
should be recycled at a designated Electrical Waste Facility.
Check with your local authority for facility locations.
Warranty Claims:
The warranty claim must be verified by the receipt with the
original Date of Purchase.
The guarantee period for the unit is 12 months. The
guarantee starts on the original Date of Purchase. In the
case of a malfunction, you may send the appliance to your
dealer, explain the malfunction and provide the original
purchase receipt.
YOU MUST HAVE THE PURCHASE RECEIPT FROM THE
ORIGINAL DATE OF PURCHASE IN ORDER TO
RECEIVE REPAIRS FREE OF CHARGE!
Within the 12 month guarantee period, we will repair unit
defects which are based on material or manufacturing faults
(it is within TableCraft’s discretion to repair or replace an
item).
These obligations to repair or replace do not extend the
period of the guarantee.
Please be as detailed as possible in complaints/inquiries in
regards to the unit when contacting TableCraft.
Any claims of good-will are excluded; we apologize for any
inconvenience this may cause.
Examples of “Claims of Good-will”:
In case of breakage (glass, porcelain or plastic)
In case of damages in transport, misuse, or lack of care,
cleaning and maintenance and in cases of neglecting to follow
operating or “drop-in” instructions
In cases of chemical and / or electrochemical effects
In cases of damage from operation the unit with an outlet with
the incorrect voltage level / unsuitable power sources
In cases of abnormal environmental conditions
In cases of repairs made by person / third party NOT
authorized by TableCraft
Table of contents
