Tadiran Telecom Coral FlexiCom 6000 User manual

Coral
FlexiCom 6000
Installation Procedure
and Hardware Reference
Manual
Creating a new world of IPportunities
(Edition 6.)

© Copyright by TADIRAN TELECOM LTD., 2004-20.
All rights reserved worldwide.
The Coral is Protected by U.S. Patents 6,594,255; 6,598,098; 6,608,895; 6,615,404
All trademarks contained herein are the property of their respectiveholders.
The information contained in this document is proprietary and is subject to all relevant
copyright, patent and other laws protecting intellectual property, as well as any specific
agreement protecting TADIRAN TELECOM LTD.'s (herein referred to as the "Manufacturer")
rights in the aforesaid information. Neither this document nor the information contained herein
may be published, reproduced or disclosed to third parties, in whole or in part, without the
express, prior, written permission of the Manufacturer. In addition, any use of this document or
the information contained herein for any purposes other than those for which it was disclosed is
strictly forbidden.
The Manufacturer reserves the right, without prior notice or liability, to make changes in
equipment design or specifications.
Information supplied by the Manufacturer is believed to be accurate and reliable. However, no
responsibility is assumed by the Manufacturer for the use thereof nor for the rights of third
parties which may be affected in any way by the use thereof.
Any representation(s) in this document concerning performance of the Manufacturer's
product(s) are for informational purposes only and are not warranties of future performance,
either express or implied. The Manufacturer's standard limited warranty, stated in its sales
contract or order confirmation form, is the only warranty offered by the Manufacturer in
relation thereto.
This document may contain flaws, omissions or typesetting errors; no warranty is granted nor
liability assumed in relation thereto unless specifically undertaken in the Manufacturer's sales
contract or order confirmation. Information contained herein is periodically updated and
changes will be incorporated into subsequent editions. If you have encountered an error, please
notify the Manufacturer. All specifications are subject to change without prior notice.

i
Federal Communications Commission
Rules Part 68 Compliance Statement
This equipment complies with Part 68 of the FCC rules. On this equipment is a label that contains,
among other information, the FCC registration number and ringer equivalence number (REN) for this
equipment. If requested, this information must be provided to the telephone company.
The REN is used to determine the quantity of devices which may be connected to the telephone line.
Excessive REN's on the telephone line may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of the REN's should not exceed five (5.0). To be certain of the
number of devices that may be connected to the line, as determined by the total REN's contact the
telephone company to determine the maximum REN for the calling area.
An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is
designed to be connected to the telephone network or premises wiring using a compatible modular jack
which is Part 68 compliant.
This equipment cannot be used on telephone company-provided coin service. Connection to Party Line
Service is subject to state tariffs.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice is not practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications in order to maintain uninterrupted
service.
If trouble is experienced with this equipment, please contact the supplier at (516)-632-7200 for repair
and/or warranty information. If the trouble is causing harm to the telephone network, the telephone
company may request you remove the equipment from the network until the problem is resolved.
The following repairs can be done by the customer: No repairs allowed.
This equipment is hearing-aid compatible.
It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is
connected. This is to avoid damaging the equipment caused by local lightning strikes and other electrical
surges.
This equipment is capable of providing user's access to interstate providers of operator services through
the use of equal access codes. Modifications by aggregators to alter these capabilities may be a violation
of the telephone operator consumer services improvement act of 1990 and part 68 of the FCC Rules.

ii
CE Compliance Statement (R & TTE)
Equipment certified according to CE has been tested and complies with the following:
EN 60950-1
EN 55022 CISPR 22
EN 55024 CISPR 24
Australia and New Zealand Compliance Statement
Equipment certified for Australia and New Zealand has been tested and complies with the following:
AS/NZS 4117
AS/NZS 60950.1
ACA TS001 TS002 TS003 TS004
AS/NZS CISPR22

iii
Federal Communications Commission
Part 15
The FCC Wants you to Know
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and the receiver.
c) Connect the equipment on an outlet on a circuit different from that to which the receiver is connected.
d) Consult with the dealer or an experienced radio/TV technician.
To ensure continued compliance with specified radio energy emissions limits of FCC Rules, the
following precautions must be observed while installing and operating the equipment:
1. Install the equipment in strict accordance with the manufacturer's instructions.
2. Verify that the power supply and associated A.C. powered equipment are connected to a
properly grounded electrical supply, and that power cords, if used, are unmodified.
3. Verify that the system grounding, including Master Ground, D.C. power system, and equip-
ment cabinets, is in accordance with the manufacturer's instructions and connected to an
approved earth ground source.
4. Always replace the factory-supplied cover or keep the cabinet doors closed when not ser-
vicing the equipment.
5. Make no modification to the equipment that would affect its compliance with the specified
limits of FCC Rules.
6. Maintain the equipment in a satisfactory state of repair.
7. Verify that emissions limiting devices, such as ferrite blocks and radio frequency interfer-
ence modules, are properly installed and functional.
8. If necessary the operator should consult their supplier, or an experienced radio/television
engineer for additional suggestions. The following booklet prepared by the Federal Com-
munications Commission (FCC) may be of assistance: “How to Identify and Resolve
Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402,
Stock No. 004-000-00345-4.

iv
FCC Warning
Modifications not expressly approved by the manufacturer could void the user authority to operate the
equipment under FCC rules.
Waste of Electrical and Electronic Equipment
(WEEE)
Directive 2002/96/EC of the European Parliament
It is the responsibility of the Distributor to fully comply with Directive 2002/96/EC dated 27 January
2003 of the European Parliament and of the Council on Waste of Electrical and Electronic Equipment
(WEEE) and with any applicable law and regulation promulgated in its respective Member State in
connection with such Directive. Accordingly, the Distributor is responsible for, and shall bear all costs
related to, the collection, treatment, recovery, reporting and environmentally sound disposal of all
electronic waste related to the products. For the purpose of this paragraph, the term “Distributor” shall
mean the person and/or entity engaged in the importation, distribution, sales, support or any other
activity carried out in the applicable jurisdiction in connection with products supplied by
Tadiran Telecom Ltd.

TOC--1
Table of Contents
1 Introduction
1.1 Document Description..............................................................................................................................1-1
Document Contents.........................................................................................................................................1-1
Related Documentation..................................................................................................................................1-3
1.2 System Description.....................................................................................................................................1-5
System Overview..............................................................................................................................................1-5
Hardware Design..............................................................................................................................................1-8
Updating from the Coral FlexiCom 5000...................................................................................................1-8
1.3 Special Symbols...........................................................................................................................................1-9
1.4 Recommended Tools...............................................................................................................................1-11
2 Hardware Installation Procedure
2.1 Site Inspection...............................................................................................................................................2-1
Space Requirements.......................................................................................................................................2-1
Installation Environment.................................................................................................................................2-3
Electrical Requirements..................................................................................................................................2-5
2.2 Equipment Installation..............................................................................................................................2-7
Unpacking the Shipping Container..............................................................................................................2-7
Cabinet Mounting and Placement...............................................................................................................2-9
Ground and Power Wiring ...........................................................................................................................2-11
Input/Output (I/O) Cables.............................................................................................................................2-20
Power Supplies ...............................................................................................................................................2-30
Circuit Card Installation.................................................................................................................................2-32
Cabling between the Control and Peripheral Shelves........................................................................2-41
2.3 Program Interface Device Connection..........................................................................................2-49
Device Connection.........................................................................................................................................2-49
3 Initial Power-Up Tests
3.1 Power Supply Test......................................................................................................................................3-1
General................................................................................................................................................................3-1
Power Input.........................................................................................................................................................3-2

TOC-2Coral FlexiCom 6000 Installation Manual
Table of Contents
TOC
Common Control Power Supply Test.........................................................................................................3-4
Peripheral Shelves Test..................................................................................................................................3-5
3.2 Common Control Test...............................................................................................................................3-9
Card Initialization..............................................................................................................................................3-9
32GC Card Lithium Battery Test................................................................................................................3-16
3.3 Shared Service &
Peripheral Interface Card Test...........................................................................................................3-19
4 Software Installation Procedure
4.1 Generic Feature Software......................................................................................................................4-1
Introduction.........................................................................................................................................................4-1
4.2 System Database Control.......................................................................................................................4-3
Saving the System Database .......................................................................................................................4-4
Loading (Restoring) the Database from the CFD...................................................................................4-6
Copying Files on the CFD..............................................................................................................................4-7
Viewing CFD Directory Details.....................................................................................................................4-9
Automatic Daily Database Back-Up..........................................................................................................4-10
Error Messages...............................................................................................................................................4-11
4.3 Hot Standby Configuration Modes..................................................................................................4-13
Hot Standby System Side Definitions.......................................................................................................4-13
Switching between System Sides .............................................................................................................4-15
4.4 Upgrading the Coral Version...............................................................................................................4-21
4.5 System Diagnostics..................................................................................................................................4-25
Peripheral Units Diagnostics.......................................................................................................................4-25
PB-ATS Fault Messages..............................................................................................................................4-27
5 External Connections
5.1 External Connections................................................................................................................................5-1
External Connections......................................................................................................................................5-1
6 Cabinet Descriptions
6.1 Cabinet Descriptions.................................................................................................................................6-1
Cabinet Structure..............................................................................................................................................6-1
Card Slot Assignments...................................................................................................................................6-5
Input/Output Champ Connections.............................................................................................................6-15
Input/Output RJ-45 Connections...............................................................................................................6-19
Peripheral Highway Cabling........................................................................................................................6-21
Tips for Peripheral Card Distribution ........................................................................................................6-23