Takara Belmont SPA MIST II User guide

SPA MIST II
QUICK OPERATION GUIDE
BB-QG-SM2-ENG 2301

3
https://beauty.takarabelmont.co.jp/manual-site/
For details and safety information
see the operating instructions.

4
1 2 3 4
123456
36°C
7
39°C 42°C 45°C 48°C 50°C 52°C
0

Level
Mist Low High
1
1 Control Panel
4 53
2
6
7
1 Start / Stop key
2 Mode selection key
3 Volume Key
4 Temperature Level Key
5
Mist Level Key
Shampoo / massage
with chemical agent
Acid hair dye
*Cooling time:5 min
Scalp cleansing agent
scalp treatment
Cosmetic for hand care
Heating-type permanent
wave agent / curling agent
Treatment / Heating-type
permanent wave agent/
curling agent
Mute Level 1
Level
Temp Low High
Level 2

5
UP
DOWN
1 Control Panel
6 Time Set Key
7 Display panel
State indication
Error indication
Time indication
Cooling and the remaining time
Shortage of water in the water-supply
bottle.Re-filling distilled water
Too much water in the machine
Preheating
Temperature detection unit error
Heater error
Temperature detection unit error
Water level detection unit error
float switch error

6
Distilled Water
2 Preparation
1 Attach the cap joint N to the mist cap (option).
2
1.Remove the water-supply bottle cap and pour distilled water.
2.Close the water-supply bottle cap.
3.Empty the drain tank and ensure that the drain
cock has been closed.
4.Insert the water-supply bottle into the top of the unit.
Empty
Pour distilled water into the water-supply bottle.
-YUME and open mist ball nozzle
-Backwash unit and YUME
-Styling chair
-CALME and men’s chair
CAUTION

7
Shampoo/massage
with chemical agent
*Do NOT use mist cap.
Hair dye
*Cooling time: 5 min
*An optional mist cap can
be used.
Scalp cleansing agent
scalp treatment
*An optional mist cap can
be used.
Cosmetic for hand care
*An optional cover can be used.
Heating-type permanent
wave agent/curling agent
*An optional mist cap can be used.
Treatment
*Cooling time: 2 min
*An optional mist cap can be used.
3 Operation procedures
1 Insert the flexible hose into the exhaust nozzle.
2 Set the main unit behind the customer.
3 Plug in and switch on the power.
4 Press the key for the desired mode.
ON
OFF
5 Press the start / stop key to implement pre-
heating.

8
6 Press the start / stop key to start the operation.
7 During operation.
Put the mist cap on and Insert the flexible hose into
the cap joint N.
Operation time change
Mist temperature change
Mist quantity change
Mode change
Sound volume change
Stop or resume the operation
5 min 2 min
8 Cooling.
9 Time-up.
3 Operation procedures

9
10 Switch off the power after finishing the work.
11 Clear out the water accumulated in the
drain tank.
12 Drain the water tank after use.
13 Accommodating the flexible hose.
ON
OFF
3 Operation procedures

10 Video
1
3
Headband
Hook and loop fastener
Zip
Stopper
Rubber protection Mist cap
4 5
2
4 Putting on / removing the mist cap
1 When using a backwash setting.
Putting on the mist cap
Removing the mist cap
6 7
1 2 3 4

11 Video
1 1
2 3
4 5 6
1 2 3 4
Headband
Zip
Stopper
Rubber protection
Mist cap
4 Putting on / removing the mist cap
2 When using in at the Styling station.
Putting on the mist cap
Removing the mist cap

TAKARA BELMONT CORPORATION
2-1-1, Higashishinsaibashi,Chuo-ku,Osaka, 542-0083, Japan
TEL : [phone]
FAX : [phone]