Eleaf Lemo 2 User manual

Notice for Use
Thank you for choosing Eleaf products! Please read this manual carefully
before use so as to use correctly. If you require additional information or have
questions about the product or its use, please consult your local agents, or visit
our website at www.eleafworld.com.
Product Introduction
The Lemo 2 is the advance version of the well-known Lemo series
atomizers due to its new innovative design of a side e-liquid fill hole and the
use of PEEK(the well-known high heat and corrosion resistance material) of
insulating piece. Vaping becomes safer and more stable, and no needs of
detaching the atomizer during refilling. The fill process becomes easier and
the leakage can be avoided. The Lemo 2 also features RBA head which
maximizes the fun of DIY experience. Meanwhile, all stainless steel
construction, visual friendly glass tube and the enlarged air-inlet hole
enhance its usefulness as well.
Standard Configuration
1× Lemo 2 Mouthpiece
1× Lemo 2 Top Cap
1× Lemo 2 Glass Tube
1× Lemo 2 Atomizer Cover
1× Lemo 2 Atomizer Tube
1× Lemo 2 Coil Stand
1× Lemo 2 Atomizer Base
1× Pre-made Heating Coil
1× Heating Coil (1m)
4× Small Screws
4× Seals Gasket (big)
2× Seals Gasket (mid)
5× Silicone (black)
2× Organic Cotton
1× Screw Driver
Lemo 2
User Manual
DIY Instructions
1. First, cut a piece of heating wire (0.5mm) in a length of 100mm long.
Next, roll the heating wire for about 7-8 circles. The diameter of the circle
is about 3mm. Bend both ends of this wire and cut out excess wire.
Note: Please use the resistance detector to check the coil before use,
make sure the resistance is at least 0.3ohm.
2. Loosen the screws on the atomizer base and install the ready-made coil
into the corresponding posts on the base. Use screws to secure the
heating coil.
3. Use a tweezers to press a certain length of cotton through the coil and
cut out the excess cotton.
4. Scatter the cotton and drip a few drops of e-liquid on it to make sure it is
moist.
Top Cap
Glass Tube
Atomizer Cover
Atomizer TubeAtomizer Base
Coil Stand
Mouthpiece
100mm
Screw

Precautions
a) Only have your Lemo 2 repaired by Eleaf. Do not attempt to repair the
unit by yourself as damage or personal injury may occur.
b) Do not leave the Lemo 2 in high temperatures or damp conditions,
otherwise it may be damaged. The appropriate operation temperature is
within -10℃to 60℃while using.
c) Do not attempt to combine the Lemo 2 with parts from other brands of
e-cigarettes. If it is damaged in this way, our company will not take on
responsibility and your warranty will be void.
Warranty
Please consult your Eleaf product warranty card. We are not responsible for
any damages caused by human error. Our warranty is not available for
products purchased from third-party vendors.
Airflow Adjustment
There is a slot on the atomizer base. By rotating the regulation ring
counter-clockwise, the slot will be covered. The more the slot is covered, the
less the airflow is.
Tips：Parallelize the atomizer and then refill it. In this case, more
liquid could be injected into the tank.
Note: 1. Please make sure the e-liquid level is between 10%-90% and leave
a small air pocket in order to avoid leakage.
2. Do not put the syringe needle directly into liquid in the tank during
refilling, or it may lead to leakage.
Liquid Refilling
First, close the air-inlet hole on the atomizer base before filling.
Next, rotate the side e-liquid fill hole cover counter-clockwise to expose
the fill hole and then slowly refill the e-liquid into glass tube.
After the liquid is filled, rotate the side e-liquid fill hole cover clockwise to
close the fill hole.
Lastly, open the air-inlet hole on the atomizer base before using
5. Finally, assemble the atomizer base, coil stand, atomizer tube, atomizer
cover, glass tube, top cap and mouthpiece together as the picture shows.
Then, it is ready to use.
Email:[email protected]
Web:www.eleafworld.com