Takerers LB12 User manual
32x32 Inch Studio BoxTakerers
User Manual
Thank you for purchasing from Takerers. For the best
peormance and safety purposes, please read this
manual carefully before using the product. Please
keep this manual for fuher reference.
Takerers
Takerers
Takerers
EN-1
Package Contents
Specications
A. 1 × Studio Tent
B. 1 × Car Bag
C. 10 × Corner Joints
D. 3 × LED Light Panels
E. 1 × Power Adapter
F. 12 × Frame Tubes
G. 5 × Backdrops
H. 1 × Soft Background
I. 1 × User Manual
A B C D FG H
IE
Takerers
Model
Input Voltage
Output Voltage
Beams Quantity
Color Temperature
CRI
Luminous Flux
Power Range
Light Box Size
LB12
AC 110-240V 50/60Hz
2300mA
210pcs
5600K
≥95Ra
≥8000LM
2-80W Adjustable
32" x 32" / 800x800mm
EN-2
Studio Box Assembly
A. Frame Assembly:
Note: Frame tubes(F) must be installed in the innermost
pa of the corner joint(C). If the installation is not in
place, the tent will not t into the bracket when assem-
bling.
1
2 3
F
C
F
C
Assemble the studio box with 12pcs frame tubes(F) and 8pcs corner
joints(C) as shown in Figure 1.
Ensure all of the frame tubes are
fully into the corner joint as it will
be crucial for the studio tent to
t on the frame properly.
When the framework is com-
plete, it should look like Figure 3.
It is now ready to be covered
with the tent.
EN-3
Take the tent out of the bag,
spread it out, then you can see
and distinguish the front and
back, left and right, as well as the
upper and lower pas of the
tent. Kindly Reminder: the inside
is silver, the outside is black.
Distinguish the direction of the
bracket and place it in the middle
of the tent cloth(gure 3). Notice
that the bracket must be stuck in
right place, otherwise the zipper
can not be pulled.
Lay the cloth evenly and at on
the brackets.
Connect all the suaces of the
tent through zippers. The zipper
should be separated from the
left and right sides, and fully
opened from the bottom of the
back.
B. Studio Tent Assembly:
1 2
3 4
EN-4
Snap the three clamps of the LED light panel(D) to the proper
position of the tubes(F), and then you can adjust its illumination
angle randomly.
The power cord of the LED light panel will be passed through the
small hole on the right side of the tent. Pull the power cord through
the opening as possible to minimize the possibility of seeing the
power cord in your pictures.
C. LED Light Panel Assembly:
1
2
EN-5
Once the wires are routed through the tent's opening, it is time to
connect with the power supply. Connect both LED light panels(D) to
the power adapter(E). Ensure that the connectors are fully seated to
ensure proper operation.
You can now plug the power pack into the power outlet. The lights
are controlled by the ON/OFF switch on the power cord.
Adjustable Brightness: You can adjust bright-
ness gradually and steadily by the dimmer
switch, which helps you to take professional
pictures and photos of objects from small to
large sizes.
Caution: The brightness of the light plate is
ve high. Do not look directly at the illumi-
nated light panel for a long time when it is on.
3
4
5
10% 50% 100%
EN-6
The bag contains 3 colors of
backdrops(G). Select the appro-
priate backdrop, peel o the
Velcro protective lm.
Your studio box comes with a soft background that can be clipped to
the frame tube and oer you soft background options; or if covered
with the LEDs, it will diuse the light, and give you more lighting
options.
Fit the backdrop under the frame
tube to hold it in place.
D. Install the Backdrop:
E. Using Your Studio Box
1 2
1
EN-7
Product features
1. Professional photo shot booth has multiple open-
ings so that you can choose any photo shooting po-
sition to get a more peect texture and beauty of
your products. You can capture your product e-
ciently from dierent angles.
2. The paiculate silver lm reective fabric inside
diuses light evenly and avoids vignetting. The pro-
vided light diuser can help you to x the problem
of highly reection light of the product, which can
show more details of the contour. Not only for be-
ginner photographers but also for advanced pho-
tographers and professionals.
F. The studio box is now completely assembled
and ready to sta taking pictures!
EN-8
Warranty
All Takerers products come with a full 1-year limited
warranty from purchase (Accessories excluded).
Damage caused by improper use or force majeure will
not be covered by the warranty.
Note: Activate your product warranty via the email.
3. Comes with 3 pieces of poweul bright light
panels (126pcs high-quality LED light beads), the
super brightness can provide sucient light source
without icker and distoion. Easy to adjust the
brightness and the angle of light bars to get the
right shot. High color rendering (90+) provides nat-
ural and vivid shooting eects.
Tips1: During installation, rotate the light bar and
inse it into the connector, which is easy and rm. If
the strength is not enough, you can use an auxilia
tool to fully inse the pole into the connector, so
that the frame will not be wider than the tent and
the zipper will not be unable to pull. Pay special
attention to the triangle area and be careful not to
use force.
Tips2: Unfold the backdrop sheet, you need to use
the cued side of the background to inse each
end under the top and bottom aps. If you install
incorrectly, the background sheet will drop.
suppo@takerers.com
Table of contents
