Takuma LOL PROFOIL FULL CARBON Setup guide

1
How to set up
your Lol profoil

3
2
Summary
Lol profoil full carbon........................................................................... p.6
Lol profoil Alu & Carbon.................................................................... p.14
Lol profoil full carbon
Lol profoil Alu (Aluminum) & Carbon

5
4
Lol profoil full
carbon

7
6
LOL PROFOIL FULL CARBON STEP 1
·1 mast : 75cm (29.5”) full carbon
·1 lol front wing
· 1 lol stabilizer
· 1 box of screws inox torx :
- Allen key
- Torx key
- Allen M6-30mm : 4 pcs (Top plate)
- M6 T-Nuts (Foil boxes)
- Torx M6-18mm : 3 pcs (Front wing)
- Torx M6-18 mm : 1 pc (Front screw stabilizer)
- Torx M6 : 14mm : 1 pc (Back screw stabilizer)
- Shimm 1.5mm (Mostly used for the 1600 cm2 front wing)
- Shimm 1mm (Mostly used for the 1300cm2 front wing)
NB : On the 1900 cm2 : No shimm are delivered (Shimm are not needed)
All the screws and T-nuts are certified stainless 316L.
This pack includes
To assemble your foil’s wing prepare the three front wing’s
screws (Torx M6-18mm) and the two back wing’s screws
(Torx M6-18mm for the front screw and Torx M6-14mm
for the back screw).
Prepare the Shimm 1.5mm for the 1600cm2, the 1mm
for the 1300 cm2 (No shimm for the 1900cm2).
Mount the foil

9
8
STEP 2 STEP 3
Drag the front wing on the fuselage’s flare, keep
the winglets up on the fuselage’s notch side
(toward the top).
Place the screws on matching holes and fix the
front wing by tightening the screws all the way.
Front wing
Place the stabilizer with the winglets in the opposite
direction of the front wing and fix it with the two
smallest screws.
Place the shimm between the fuselage and the stabilizer.
Fix the front screw first (Torx M6-18mm) then the back
screw (Torx M6-14mm).
Stabilizer
(Torx M6-14mm)

11
10
Place the top plate of the carbon mast with
the 4 screws (Allen M6-300mm).
Make sure to screw them in diagonal and make
sure your mast is straight in foil boxes.
No need to tight the screws too much
(It can damage your foil boxes or your boards).
You are now ready to ride...
Assembly
STEP 4 RESULT
1. .4
3. .2
NB : Follow the placement order
of the screws in the diagram.

13
12
Lol profoil
aluminum & carbon

15
14
LOL PROFOIL ALU & CARBON STEP 1
· 1 mast : 70cm (27.5”) anodized aluminum
· 1 lol front wing carbon
· 1 lol stabilizer carbon
· 1 fuselage
· 1 universal Top plate
· 1 carrying bag for the all set
· 1 box of screws inox torx :
- Tef GEL
- M6 T-Nuts (Foil boxes)
- Shimm 1.5mm (Mostly used for the 1600 cm2 front wing)
- Shimm 1mm (Mostly used for the 1300 cm2 front wing)
- Torx key
- Torx M6-18mm : 4 pcs (Front wing)
- Torx M6-14 mm : 2 pcs (Stabilizer)
- Torx M6-25mm : 5 pcs
- Torx M6-30mm : 7 pcs (3 pcs for Mast - 3 pcs for
universal top plate)
This pack includes
To assemble your foil’s wing prepare the three front wing’s
screws (Torx M6-18mm) and the two back wing’s screws
(Torx M6-16mm).
Prepare the Shimm 1.5mm for the 1600cm2, the 1mm
for the 1300 cm2 (No shimm for the 1900cm2).
Mount the foil

17
16
STEP 2 STEP 3
Drag the front wing on the fuselage’s flare,
keep the winglets up on the pole’s notch side.
Apply tef gel on the screws before placing
them on matching holes and fix the front wing
by tightening the screw until blocking.
Front wing
Place the shimm between the fuselage and the stabilizer.
Place the stabilizer with the winglets in the opposite
direction of the front wing and fix it with the two
smallest screws.
Stabilizer

19
18
STEP 4 STEP 5
Place the top plate on the mast and
fix with 3 screws (Torx M6-30mm).
Mast
Place the mast in the fuselage, fix with 3 screws
(Torx M6-30mm).
You are now ready to ride...
Assembly