Talk Audio Visual PROMIC PA-300W User manual

USER MANUAL
PORTABLE PA AMPLIFIER SYSTEM
PROMIC PA-300W
SOUND

Table of Contents
CONTENTS
1. Main Features and Quick Start Guide 1
3. Important Safety Information 3
2. Introduction and Product Specifications 2
11~14
15~18
6. Digital Audio Player With Bluetooth Operation Guide
4~6
7~10
4. Parts Description and Operation Guide
5. Wireless Microphone Operation Guide
20~21
22~23
10. Useful Tips on Using Your PA System
11. Warranty Information
19
20
8. Rechargeable Battery Guidelines
9. Setting up Your Portable PA System
7. Multi Format CD / DVD / USB / SD Media Player with Bluetooth

1
1.1.1. Fully charge the unit for 7-10 hours before first use.
1.1.2. The wireless microphone(s) have been pre-configured to a suitable channel during testing. If you have a
second wireless microphone receiver installed this is set to a different channel.
1.1.3. Insert the AA batteries into the handheld wireless microphone and turn on the microphone. Turn on the wireless
receiver located on the top rear of the system by turning the volume switch to the right until it clicks on and
the lights are illuminated. The red RF light will be on when the wireless microphone and wireless reciever
are paired. Adjust the level of the microphone by the volume adjustment and the master volume control.
1.1.4. To play music or other audio insert a USB flash drive with stored MP3 files. Or connect any Aux device such
as smartphone using the supplied audio cable.
1.1.5. To initialise Bluetooth mode short press MODE on Digital Media Player. On device open Bluetooth settings
and connect to PA SYSTEM. When paired the LED on the Digital Media Player will display 'Bluetooth Connected'.
WARNING:
Do not connect any external device to USB slot other than USB flash memory drives.
This slot is not designed to charge or connect phones or any other USB device.
The voltage may damage the device.
MAIN FEATURES
1. Main Features
·Fully self-contained all-in-one portable audio system.
·High performance class D amplification.
·12 inch woofer and 1 inch tweeter drive.
·Sturdy injection moulded ABS impact resistant plastic body - extremely durable.
·Operate using mains power or built-in 25.2V 8Ah rechargeable battery.
·Up to 5 hours continual use on a full battery charge.
·Wireless handheld microphone transmitter included.
·Wireless microphone receiver with volume control included.
·Expansion slot for option of second wireless receiver for second wireless microphone.
·Wireless body pack transmitter with headset & lapel microphone available as option.
·Wired microphone 6.35mm / XLR inputs.
·Optional:
Multi-format Bluetooth media player with USB and SD card playback. Optional CD / DVD player available.
·Remote control for media player.
·Aux inputs for external music players such as smart phone etc.
·Pull up handle, wheels and carry handle for easy transportation.
·Audio line out to companion speakers.
·Video out for connection to screen or projector (Optional DVD player only).
·Voice priority function - fades music when microphone in operation (With on / off switch).
·Tone (base and treble) and echo reverb controls.
·35mm tripod stand mount bracket in base (Tripod stand sold separately).
The Promic range of Portable Public Address systems are the ultimate on-the-go take anywhere
wireless solution.
1.1. Quick Start Guide

2
Thank you for choosing the PROMIC PA-300W Portable PA amplifier system. In order to get the best
performance, please read this manual carefully before use. Please recharge this unit every month
to achieve the best battery performance.
2. Introduction and Product Specifications
2.1. Introduction
2.2. Product Specifications
PROMIC PA-300W
Audio Input - Wired Microphone
Power Output
Amplifier
Frequency Response
Bass Driver
Horn Tweeter
Distortion
Audio Input - Line In
Active Audio Output
Inactive Audio Output
Video Output
AC Power Supply
Internal Battery
Charge Time
Standby Time
Battery Indicator
Battery Compartment
Colour
Grille
Tripod Mount
Dimensions (L x W x H)
Weight
Operation Temperature Range
300W MAX 150W RMS
Class D
50Hz-18K z±3dBH
12'' Woofer Speaker
1" Tweeter
1% (at 10W)
2 x Combined 6.35mm / XLR
1 x 3.5mm, 1 x 6.35mm, RCA (L) RCA (R)
6.35mm Active
RCA (L,R), 6.35mm
RCA
100-240V switching power supply
25.2V 8A Rechargeable Lithium Battery
Around 8-10 Hours
4-6 Hours ( depending on volume setting)
Battery status. Low power
Rear accessible panel with 8 service screws
Black
1.5mm Steal with Powder Coat Finish
Moulded 35mm Tripod Mount on Base
400 x 595 x 340 mm
19.5kg
5 - 35C
INTRODUCTION AND PRODUCT SPECIFICATIONS

3
3. Important Safety Information
In the event of a technical failure, please contact the your local dealer. Unauthorised repairs will void
the warranty. One receiver cannot receive a signal from two or more same frequency microphones simultaneously.
Other brands of wireless microphones with different frequencies cannot be used with this system.
IMPORTANT SAFETY INFORMATION
Do not open this product by yourself for adjustment. To reduce the
risk of fire or electric shock, do not remove the cover. High voltage
parts are inside.
8
Do Not
Disassemble
Do Not
Touch
Pull Out
AC Plug
Forbidden
Forbidden
To reduce the risk of fire or electric shock from damaged power cord,
do not pull power cord strongly when pulling out the power plug.
Always grasp the plug tightly then pull it out. Turn off the power if
this equipment will not be used for a long period of time after setup.
To reduce the risk of electric shock, use the specified power voltage
only. Do not expose equipment or power cord to strong sunlight or to
moist or dusty conditions.
To prevent damage from impact, do not place heavy objects on
top of this equipment or place on uneven surfaces.
Insert the power plug into power outlet entirely and clean regularly.
Please pull out power plug and contact your dealer when the
following happens:
① When smoke comes out with burning smell from this equipment.
② Water or other liquid is accidentally spilt on this equipment.
③ Dropped on the ground and unit is damaged.
④ Power cord damaged (Cord core exposed or cord broken).
⑤ No sound output.
To reduce the risk of electric shock, do not touch power outlet during
an electrical storm. Do not touch power plug with wet hands. Do not
put vessel with liquid or small metal parts on the top of this equipment.
Do not let metal or flammable parts drop into this equipment.

4
(Pictures for reference only)
4. Parts Description
4.1. Main Unit
(1) Handle
(2) Telescopic Trolley
(3) Tweeter Speaker
(4) Woofer Speaker
(5) Speaker Grill
(6) Speaker Stand Mount
(7) Wheels
(8) Multi Format CD / DVD MP3 Player
or Digital Audio Player
Fixed Carry (9) UHF PLL Wireless Receiver Modules
(blanking plate fitted if no optional
second receiver installed)
(10) Control Board
(11) Power Supply
(12) AC Input
(13) Amplified Speaker Out
(14) Battery Compartment
PARTS DESCRIPTION
Front View Rear View
(4)
(6)
(1)
(3)
(2)
(1)
(8)
(5)
(7)
(9)
(10)
(11)
(12)
(13)
(14)

5
(Pictures for reference only)
PARTS DESCRIPTION
4.2.1. PA-300W Control Panel
(4)(2) (3)
(7)(5)
(8)
(9) (10) (11) (17)
(12) (13)
(15) (16)
SD/MMC C ARD
MOD E REP T.
DI G I TAL AUD I O P L AYE R
SD +U SB
POWE R
(1)
(19)
(14) (18)
(20)
(6)
(1) Power Switch
(2) Power LED Indicator:
When voltage is low, red light appears.
(3) Battery Status LED Indicator:
Battery Supply: When battery voltage
reduces from strong to weak, green
indicator will extinguish one by one
from right to left.
Battery Charge: When charging battery,
power indicator will flash, with battery
voltage enhancing from weak to strong,
the indicator will light one by one, from
left to right.
(4) Voice Priority Switch
(5) Volume Control MIC 1
(6) MIC 1 Input
(7) Volume Control MIC 2
(8) MIC 2 Input
(9) Tone Control
(10) Echo Control
(11) Volume Control for AUX
(12) Line In
(13) Line Out
(14) Video Out
(15) Media Player ON / OFF and
Volume Control
(16) Bass Control
(17) Treble Control
(18) Master Volume Control
(19) MP3 Player
(20) Receiver Module

6
4.2.2. PA-300W Control Panel Operation
OPERATION GUIDE
Note: Before using this device, please use AC cord to charge internal battery.
Recharging time is 7-10 hours.
1. (A) When using AC power, switch power (12) , power LED indicator (2) lights in
green to indicate normal condition.
(B) When using built-in rechargeable battery, remove AC cord and switch power (1) on, power LED
indicator (2) lights up in green to indicate normal condition. When Battery Status LED indicator
(3) lights up in red, it indicates low battery power and a recharge is necessary.
(C) If battery voltage is very low the main unit will be powered off automatically.
(D) Insert the power cord into AC input jack (12) (4.1. Main Unit) and the device charges
automatically.
2. Turn on handheld microphone or body pack transmitter (optional) power switch, RF LED indicator
on wireless receiver will light. This indicates receiver has received microphone RF signal.
3. For wired microphone (optional) use, insert wired microphone cable into MIC 1 (6) or MIC 2 (8) ,
adjust volume control (5) or (7) accordingly.
4. If connecting system to external amplifier / speakers or second Promic PA System, connect audio
cable into LINE OUT (13), then connect to external amplifier / active companion speakers. This
output signal is combined from all inputs.
5. For more sound coverage connect a second non-powered / passive extension speaker into
amplified speaker out.
Note: This feature is designed for 8 Ohm minimum impedance speakers. Overall amplifier output will
be split between both speakers when in use.
6. To connect external audio devices such as portable music players smart phones connect via Line
Input (12) with suitable audio lead.
7. Instruments such as guitar should be connected to Line Input (12).
8. This unit has ECHO control (10) suitable for microphone use.
9. VOICE PRIORITY Function - fades music when microphone is in operation (4).
10. For recording insert audio lead to LINE OUT (13) and connect to suitable audio recording device.
Notes:
1. To use built-in rechargeable , please recharge the battery before operation. Switch off the
power, plug in AC Cord to start to charge. Charging time is about 10 hours. Please recharge this unit
every month.
2. If this system is not going to be used for a long time, charge the at least once a month. Pull
out power plug and turn Power Switch to OFF position. See page (19) for more battery care guidelines.
on (4.1. Main Unit)
jack
/
battery
battery

5. Wireless Transmitter
WIRELESS MICROPHONE - PARTS DESCRIPTION
(Pictures for reference only)
5.1. Wireless Handheld Microphone Transmitter
5.2.1. Open battery cover (8) and insert 2 x AA batteries paying attention to the polarity
indicated with + or -.
5.2.2. Turn on microphone POWER switch (4), POWER LED indicator (2) will light up,
low battery indicator (3) will flash once then off. When LOW battery indicator (3)
lights up red, it indicates battery power is LOW. Please change battery for
continued use.
5.2.3. When switching on microphone power, operate the switch step by step. When
the switch moves to the centre, please stay for at least 0.5 second to avoid
any noise through the system. Then move to ON position.
5.2. Wireless Handheld Microphone Operation
(7)
(8)
(6)
(5)
(6)
(2)
(3)
(1)
(9)
(4)
(1) Mesh & Capsule
(2) POWER LED Indicator
(3) Low Battery LED Indicator
(4) POWER Switch (ON / OFF)
(5) Microphone Body
(6) Replaceable Cap
(7) Battery Compartment
(8) Battery Cover
(9) IR SYNC Window
7

5.3. Wireless Handheld Microphone Specifications
Microphone Type
Frequency Range
Channel Set-up
Spurious Emissions
Transmitting Power
Power Source
Operating Time
On-board Indicators
Dimensions
Weight
Dynamic Handheld
PLL 16 Channel Selectable
UHF-5R (520.05 - 543.75 MHz)
IR Sync
>55dBm
10mW
2 x AA 1.5V Batteries (Included)
Approx >8 Hours
Power Status / Low Battery / On / Off Switch
Ø 50 mm, L 260mm
270g
WIRELESS MICROPHONE - PARTS DESCRIPTION
8

6. Wireless Receiver Module
WIRELESS MICROPHONE - PARTS DESCRIPTION
(Pictures for reference only)
6.2. Wireless Receiver Module Operation
The PA-300W can have up to 2 x wireless microphone receivers installed into the expansion
slots located centre right and centre left of the PA-300W control panel.
6.1. PLL Infrared Sync Receiver Module
NOTE: The wireless microphone has been synched by default to a suitable channel during
testing. If you have a second wireless microphone receiver installed this is set to a different
channel. Please use the steps below if you wish to change the channel of the wireless receiver /
microphone:
6.2 1. Long press (3 seconds) the SET / SYNC key on the receiver, switch to desired
channel by UP / DOWN key when indicator bar is flashing.
6.2.2. Short press SET / SYNC key to confirm the desired channel. The indicator bar
will stop flashing when the channel is selected.
6.2.3. With the handheld wireless microphone turned on, remove the battery cover.
Face IR window to receiver IR window within 5-10cm.
6.2.4. Short press SET / SYNC again, the RF LED indicator will light up when the
transmitter is paired on the selected channel on the receiver.
6.2.5. For the optional body pack transmitter follow steps 1 and 2 above and then simply
match the displayed number on the receiver LED display and match with frequency dial
on the body pack transmitter.
6.2.6. Only one wireless microphone can be connected to one wireless receiver. If a second
wireless microphone is required then a second wireless receiver must be installed.
.
(1) On / Off Power and
Volume Control
(2) SET / SYNC Button
(3) RF LED Indicator
(4) IR (Infrared) Sync Port
(5) LED Display Screen with
Frequency Channel Number
(6) Frequency Modulate (Up)
(7) Frequency Modulate (Down)
Rear View (1)(2) (5)(4) (3) (6)(7)
9

6.3. Wireless Receiver Specifications
Receivers
Frequency Range
Preset Channels - UHF-5R
Oscillation Mode
Receiving Mode
Frequency Response
Sensitivity
T.H.D
AF Output
SNR
Distortion
Spurious Emissions
Channel Set-up
Display
Working Distance
Antenna
Current Consumption
Maximum Two Wireless Receivers (Horizontal)
UHF-5R (520.05 - 543.75 MHz)
CH 1 - 520.05 MHz; CH 2 - 520.75 MHz; CH 3 - 521.85 MHz;
CH 4 - 522.45 MHz; CH 5 - 523.35 MHz; CH 6 - 524.35 MHz;
CH 7 - 525.15 MHz; CH 8 - 525.85 MHz; CH 9 - 527.95 MHz;
CH 10 - 530.25 MHz; CH 11 - 531.95 MHz; CH 12 - 534.65 MHz;
CH 13 - 536.55 MHz; CH 14 - 538.95 MHz; CH 15 - 541.45 MHz;
CH 16 - 543.75 MHz
PLL Synthesized
80Hz-15KHz (± 3dB)
-95dBm S/N≥40dB
≤1%
≤1%
450mV ± 50mV
>80dB
< 1%
>80dB
IR Sync (Handheld Microphone)
Manual (Optional Body Pack Transmitter)
LED Channel Display, RF, IR
Up to 50m (Ideal)
Built-in / Internal
130mV ± 20mV
WIRELESS MICROPHONE - PARTS DESCRIPTION
10

DIGITAL AUDIO PLAYER
7. Digital Audio Player With Bluetooth
7.1 Parts Description
A. Front Panel
B. Remote Control
SD/MMC C AR D
MO D E R EPT.
DIGITAL AUDIO PLAYER
SD+USB
POWER
(1) (2) (3) (4) (5) (6)(7) (15) (14)(13)
(Pictures for reference only)
(1) / Power
(2) Play / Pause
(3) Stop
(4) Repeat
(5) Skip Previous / Rewind
(6) Skip Next / Fast Forward
(7)
(8) Mute
(9) VOL-
(10) VOL+
(11) EQ
(12)
(13)
(14)
(15) USB P
Mode
IR Signal Receiving Port
LCD Display
SD Card Slot
ort
Key
Number Keys
(12)
(1)
(3)
(1)
(2)
(8)
(4)
(5)
(6)
(11)
(9)
(10)
EQ
MODE
STOP
0
3
21
5
4
8
7
6
9
11

C. Digital Audio Player Specifications / Functions
DIGITAL AUDIO PLAYER
WARNING:
Bluetooth
USB
SD
On-Board
Functions
Bluetooth 2.0 Pairing with Appropriate Device
Supports MP3 / WMA USB 2.0 High Speed Playback from Solid State
USB Drive up to 16GB
Supports MP3 WMA Playback from Solid State SD Card up to 8GB /
Mode Power On Off, Play Pause, Stop, Repeat, Skip Previous
Rewind, Skip Next / Fast Forward
/ / / /
Do not connect any external device to USB slot other than USB Flash Memory drives.
This slot is not designed to charge or connect phones or any other USB devices. The
voltage may damage the device.
Remote
Functions
Power On Off, Stop, Mute, Mode, Return, EQ, Skip Previous Rewind,
Skip Next Fast
/ /
/ Forward, Play / Pause, Vol -, Volume +, Numeric Key
Display
EQ Modes
LCD Display Including Artist, Song Name, Modes etc
Jazz, Rock, Pop, Classic
12

7.2. Operation Guide
DIGITAL AUDIO PLAYER
Basic Operation
7 2 1. Switch on the MP3 / Power switch on the PA System main control panel and set to
appropriate volume level. Long pressing “MODE” (1) on the player or Power Key (1)
also turns the multi format MP3 player on and off.
7.2.2.
automatically; If both SD card and USB are inserted simultaneously, press "SD / USB"
(15) to shift between the drives.
Connecting Bluetooth Device
7.2.3. Short press 'MODE' on media player or remote control to initialise Bluetooth mode.
Open Bluetooth settings on Bluetooth device (such as a Smartphone, tablet, iPod etc)
and connect to 'PA SYSTEM'.
7.2.4. When paired the LED on the PA System will display 'Bluetooth Connected'.
7.2.5. The Bluetooth device and PA SYSTEM are now connected for streaming music
wirelessly from device.
Playback Operation
7.2.6. On front panel or remote control, press "PLAY / PAUSE" (2) once to pause while
track is playing, press again to resume play.
7.2.7. On front panel or remote control, Short press "Skip Previous / Rewind" (5):
Skip Previous; Long press: Rewind.
7.2.8. On front panel or remote control, Short press "Skip Next / Fast Forward" (6):
Skip Next; Long press: Fast Forward.
7.2.9. MUTE mode: On remote control, Short press "MUTE" (8) for mute mode.
7.2.10. REPEAT mode: Press "REPEAT" (10) enter into repeat play setting:
a. Repeat all: repeat all the songs in the selected memory
b. Random: play all the songs in random order
c. Repeat one: repeat only the current selected song
. .
Insert SD card into slot (16), or insert USB flash drive into slot (17). Files will be read
Repeat One
Repeat All Random Play
13

7.2.11.
preset are available:Natural, Jazz, Rock, Pop, Classical.
General Warnings:
a. Before using a new (unformatted) USB Flash Drive or SD Flash Card with the digital audio
player please format the card (FAT32).
b. If the player freezes up for any reason, turn it off for 3 seconds, and then turn the power
back on.
c. Do not connect any external device to USB slot other than USB flash memory drives. This
slot is not designed to charge or connect phones or any other devices.
Equalizer: Short press "EQ" (8) to adjust equalizer, the following equalizer
Natural Rock Pop Classic
Jazz
DIGITAL AUDIO PLAYER
14

(16) (15) (9)(1) (3)
(7) (11)(5) (4) (8)(13)(10)
VOL- VOL+PWR MODE/EJECT
BAND
IR
(12)
1234
5678
9
VOL+
VOL-
010+
MUTE
b#
BANDFUNC
LOUD
SLOW
MENU
ZOOMENTER
AUDIO
ST
SETUP
AMS ANGLE SUB
TITLE
SEL
REPEAT PROG
TITLE
GOTO
DIS
PLAY
(25)
(22)
(30)(28)
(31)
(33)
(2)
(20)
(23)
(8)
(4)
(16)
(35)
(36)
(7)
(9)
(14)
(21)
(26)
(27)
(15)
(29)
(34)
(32)
(37)
(17)(19)
(18)
(24)
(5)
(6)
MULTI FORMAT CD / DVD / USB / SD MEDIA PLAYER
8. Multi Format CD / DVD / USB / SD Media Player with Bluetooth
8.1. Parts Description
Remote Control
(Pictures for reference only)
15

16
(1) DISC Slot
(2) Power Switch
(3) Power / Mode Button
(4) Short Press: / Chapter;
Long Press: ;
On the Radio by Scanning.
(5) Short Press: / Chapter;
Long Press: Fast Forward;
On the Radio by Scanning.
(6)
(7) Band Mode
(8) Play / Pause
(9) Eject
(10) USB Port
(11) SD Card Slot
(12) Infrared Sensor
(13) LCD Display
(14) Mute
(15) VOL+
(16) VOL-
(17) Pitch Up
Skip Previous
Rewind
Skip Next
Function Mode
(18) Pitch Down
(19) Default
(20) Loud
(21) Audio / ST
(22) Zoom
(23) Arrow Buttons
(24) Menu Enter
(25) Setup / AMS
(26) Key for Angle
(27) Sub / Title / Language Setting
(28) Repeat
(29) PROG
(30) Slow
(31) Key for Title of DISC
(32) Key for DSP-Off, Loud on,
Volume / Function Selection
(33) Menu
(34) Stop / Back
(35) Number Keys
(36) GOTO Playing Time Setting
(37) Display Time
8.2. Parts Description
Do not connect any external device to USB slot other than USB flash memory drives. This
slot is not designed to charge or connect phones or any other USB device. The voltage may
damage the device.
WARNING:
MULTI FORMAT CD / DVD / USB / SD MEDIA PLAYER

17
8.3. Operation Guide
8.3.1. Press Power switch (2) to turn on the multi format player, press again to switch off.
8.3.2.
8.3.3.
8.3.4. While the multi format player is working, if there is no disc in (1), then the LCD display (13)
will display "NO DISC", if the disc has not been placed correctly, the LCD display (13) will
also display "NO DISC"; If the disc has been placed correctly, the LCD display (13) will
display TITLE and Playing Time.
8.3.5. While the file is playing:
a. Press key PLAY / PAUSE (8) on the multi media player or key PLAY / PAUSE (8) on the
remote control, the file will be stopped, it will display PAUSE on the LCD display, press
again to resume PLAY.
b. Press key STOP (3) on the multi player or key STOP (34) on the remote control,
file will be stopped and the LCD display (13) will be displayed STOP on the LCD display.
(a). While the file has been stopped, press key PLAY / PAUSE (8) on the multi player
or key PLAY / PAUSE (8) on the remote control, the current file can be played again.
(b). While the file has been stopped, repeat press key STOP / BACK (34) on the remote
control, then press key PLAY / PAUSE (8) on multi format player or the Key PLAY /
PAUSE (8) on the remote control, the first file will be played.
8.3.6. Press key EJECT (9) on the multi format player or key EJECT (9) on the remote control, the
disc will be ejected automatically, and it will take about 30 seconds to slot the disc in
automatically again.
8.3.7. (4) / (5)
8.3.8. Press key BAND (7) on the multi format player is with. On the radio for the band. Press key
FUNC (6) on the remote control, you can select function radio / palyback of / USB / SD.
8.3.9. While the DISC is playing. Press key BAND (7) on the remote control to select NTSC, PAL,
AUTO.
/ (3)
To connect via Bluetooth, short press key "MODE" (3) on control panel to initialize BLUETOOTH
mode. The LCD display will read "NO LINK'. Open Bluetooth function on device and search.
Device will find "PA SYSTEM" after the search. The LCD will display "LINK OK" when it is
paired. Audio from the Bluetooth device will then be transferred to PA SYSTEM.
The built-in DVD player uses the high quality DVD movement, can play the whole region in
multiple formats of DVD / DVD-9 / VCD / DVCD / MP3 / CD-R / RW and other formats.
Selection / music / fast forward / backward : press this button in the radio can be
upper / lower search radio. In SD / USB can be read, upper / lower selections, long press
fast forward / rewind.
format the
format
MULTI FORMAT CD / DVD / USB / SD MEDIA PLAYER

18
adjust the volume. Press key VOL+ (15) to increase volume, press key VOL- (16) to
decrease volume; Press key # (17) / key b (18) on remote control to adjust pitch control,
Press key # (17) to adjust pitch up, press key b (18) to adjust pitch down; Press key MUTE
(14) on the remote control to mute the audio,
to resume audio; Press key (19) to resume original audio.
8.3.11. While playing CD, press LOUD (20) on the remote control to increase the bass effect.
8.3.12. While playing CD, press (21) on the remote control to select left channel, right channel and
stereo. Please be noted to select voice mode you should pay attention to various kinds of
discs, some of the disc that only have one voice mode, when the key voice mode has been
selected, it will be displayed on the LCD display.
8.3.13. Under the mode of playing DVD / VCD, Press button (22) on the remote control to zoom in
or zoom out the image, Press (30) to play slowly. Press (31) to return to sub catalog.
8.3.14. Press MENU on the remote control to set up main menu (33), then the PBC can be played,
all the menu will be displayed on the LCD disc player, and then press Numeric Key (35) to
select the song, while playing any of the songs on the PBC, press again to cancel the PBC
playing. While playing DVD, press (33) once to set up the main menu, or return to main
menu, all the menu will be displayed on the LCD disc player, and then press Numeric Key
(35) to select the chapter, press again to enter into title menu, press thrice to switch off;
Press (26) on the remote control to select the angle of viewing the image.
8.3.15. The language of the DVD can be set up according to the disc. Press (27) on the remote
control to change the language. Subtitles can only be selected in DVD mode.
8.3.16. To set the sequence of pre-recorded files, press (29) on the remote control. P00:00 will be
displayed. Press the Numeric Key (35) to select playing sequence of the files to be
programmed. Press (23) to play.
8.3.17. Press (25) on the remote control to enter in to main menu, then press (23) to setup the
standard of TV system, audio, media, Television system and code etc ( You can choose the
current setting with the multi media player without changing ).
8.3.18. Press (28) to repeat the single file or all the files.
8.3.19. Repeat pressing (32) on the remote control to select the acoustic characteristic.
8.3.20. Press (37) to know the total lead time and time left for the files.
8.3.10. While video output or audio output, press key VOL+ (15) / VOL- (16) on remote control to
the LCD display will display MUTE, press again
MULTI FORMAT CD / DVD / USB / SD MEDIA PLAYER