Talkaphone Ms-600 User manual

MS-600

Flush Mounting Sleeve

Installation Manual

Page 1of 5Rev. 12/23/2020

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, Scream Alert, WEBS, and WEBS Contact are registered trademarks of Talk-A-

approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated.

I. Introduction

This Installation Manual provides detailed instructions for a typical installation of the MS-600. It is

highly recommended that this manual be read in its entirety before starting any installation.

II. Contents

Please ensure receipt of each of the included MS-600 components:

QTY

Part Number

Description

24541

Flush Mounting Sleeve

67595

Gasket for Flush Mounting Sleeve

67598

Paper Mounting Template (MS-600)

III. Installation

1. Mount the MS-600flush mounting sleeve into a stud wall, cement block, brick wall, or other wall

type. MS-600 must be installed so that the Call Station gasket seals properly with the finished

wall surface. Note that the Call Station faceplate, gasket, and the lip of the MS-600 unit will sit on

top of the finished wall surface. See Figures (1) and (2).

2. Install the top and bottom supports for the MS-600 flush mounting sleeve; these are set at a

distance of 10.50 inches (typical). The distance from the bottom support of the MS-600 to the

ground is dictated by the distance from the Call Station pushbutton to the ground per ADA

requirements. See Figure (1).

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE

APPLICABLE INSTALLATION CODE (FEDERAL, STATE, AND LOCAL)

BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION

OF THE PRODUCT AND THE HAZARDS INVOLVED

PLEASE NOTE THAT THIS INSTALLATION MANUAL IS INTENDED TO

BE USED AS GENERAL INSTALLATION GUIDANCE. INSTALLATION

REQUIREMENTS IN THE FIELD MAY VARY.

MS-600

Flush Mounting Sleeve

Installation Manual

Page 2of 5Rev. 12/23/2020

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, Scream Alert, WEBS, and WEBS Contact are registered trademarks of Talk-A-

approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated.

Figure 1. Considerations for installation into drywall framing.

Figure 2. Overview for installation of the MS-600 flush mounting sleeve and gasket into finished drywall.

MS-600

Flush Mounting Sleeve

Installation Manual

Page 3of 5Rev. 12/23/2020

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, Scream Alert, WEBS, and WEBS Contact are registered trademarks of Talk-A-

approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated.

3. After all supports have been properly installed, use the provided template to create the necessary

cutout for the MS-600 flush mounting sleeve. Along with the main cutout, six (6) clearance holes

may need to be drilled around the cutout to provide a proper mating surface between the unit and

the mounting wall. See Figure (3).

Figure 3. Exploded overview of installation.

4. Upon completing the cutout, insert the MS-600 with included gasket and secure the MS-600 to

the support beams with four (4) self-drilling fasteners (fasteners not provided by Talkaphone).

MS-600

Flush Mounting Sleeve

Installation Manual

Page 4of 5Rev. 12/23/2020

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, Scream Alert, WEBS, and WEBS Contact are registered trademarks of Talk-A-

approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated.

5. The MS-600 is equipped with two (2) knockouts for 3/4-inch conduits. These may be used to

connect conduit to the MS-600 flush mounting sleeve so that the Call Station can receive power

and/or communication. The knockouts are both located on the bottom and at the rear of the MS-

600 flush mounting sleeve as shown in Figure (4).

Select the knockout(s) to be used and strike out the appropriate knockout(s) and install the

conduit to the MS-600.

Figure 4. Location of knockouts.

MS-600

Flush Mounting Sleeve

Installation Manual

Page 5of 5Rev. 12/23/2020

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, Scream Alert, WEBS, and WEBS Contact are registered trademarks of Talk-A-

approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated.