Tamron 300QV-P-CM User manual

Mounting and Installation Manual
Precautions when attaching a side cable type mount bracket and install-
ing onto a gypsum board, etc. which does not have enough strength
Please read this guide carefully along with the camera's "Owner's
Manual - Installation" to attach properly.
Precautions (Make sure you follow the instructions)
Warning
The camera must be attached to the site where its durabil-
ity is strong enough to ensure the camera's gross weight
Attaching the camera on a ceiling etc. where the strength is insuffi-
cient may cause injury by dropping onto the body from the height.
Before attaching, reinforce the site strong enough to endure
the camera weight.
●
Do not scratch your hand at the metal edge.
Strongly scratching your hand may cause injury.
Periodical inspection is required
Rusted metals and screws may cause dropping the camera
from the height.
Contact the store for inspection.
●
Advices on Installation
1. Before installing, check that the mounting location is strong
enough to endure the gross weight (approximately 0.6kg) of
the camera.
When installing the camera onto a gypsum board, etc. which does
not have enough strength, provide sufficient reinforcement or use
a commercially available gypsum board anchor, etc. to ensure
enough strength, then properly attach the camera following the
specified precautions.
2. Make sure to use the anti-drop wire (supplied) when installing.
3. Use the fixation screws (supplied) to secure the camera and
mount bracket to make sure that they do not wobble.
Cautions: Since this camera uses fisheye lens, it sticks out from the main
body. Attach the lens protective cover to the camera and do not
remove it before starting installation and adjustment. Be careful
not to scratch or leave stain on the surface of the lens.
Check the Contents (Operation Manual - Installation - continued)
Other than those specified in "Owner's Manual ■Included Items," the fol-
lowing products are included. After opening the packaging, please make
sure all the products are included:
Included Items (Additional items)
Mount bracket Mounting and Installation
Manual (this document)
Camera unit mounting screws
(M4 x 15) 2 pcs
■
5°
R99
4.3
98.2
41.75
23
35
70
35
41.75
70
53.5 51.3
5-Ø4.3
Ø46
(13.1)
7.7
Mount bracket - template -Dimensions
Unit: mm
Ø50
4.3
R99
23
98.2
70
35 41.75
51.353.5
41.75
23
35
70
Note:
Make sure to screw
4 sites including
the spare holes.
•
When mounting directly on the
ceiling (wall), drill a Ø50 hole here.
Spare hole
4-Thread hole
Spare hole
EN300QV-P-CMA4Sheet.indd1EN300QV-P-CMA4Sheet.indd1 2013/04/2213:22:032013/04/2213:22:03

1. Place the template (printed on this document) and drill thread holes
When using a gypsum board anchor, etc., follow the precautions such
as a thread hole diameter.
Commercially available gypsum
board anchor
Sample of board anchor
2. Attach the mount bracket
Use 4 commercially available screws to secure the mount bracket.
Note:
The screws of 4mm diameter must be long enough to mount the camera.•
3. Attach the anti-falling wire to the camera
Mount the washer using the wire fixing
screw.
→See "Owner's Manual - Installation" Anti-falling wire
How to Mount
Mounting on the wall with a mount bracket
4. Insert the anti-falling wire to the hook of the mount bracket
(See 1, 2and 3below)
Hook the wire from the bottom notch 1, rotate it 2and make it look as shown
in 3.
5. Mount the camera to the mount bracket and secure it with the 2
camera unit mounting screws (supplied with the mount bracket)
Insert the camera cables between the
groove of the camera unit and the U
shaped notch of the mount bracket
and make sure there no cables are
wedged.
●
Note:
The notch must be placed
so that it comes to the up-
per side of camera image.
•
Lens protective cover
Camera unit mounting screws
Anti-falling wire
1
2
3
Mounting on the ceiling with a mount bracket
When installing the camera onto the ceiling and the ceiling material is
a gypsum board, etc. which does not have enough strength, provide
sufficient reinforcement or make sure to use a commercially available
gypsum board anchor, etc. along with the mount bracket.
Drill holes for the mounting screws, mount the camera in the same man-
ner as shown above Step 1to 5.
Make sure the anti-falling wire is inserted through the
hook of the mount bracket.
●
Mounting directly on the ceiling
(Same for mounting directly on the wall)
This procedure should be done only when the mounting screws can
reach the ceiling beams or structural materials and sufficient mounting
strength is ensured.
1. Place the template (printed on the Owner's Manual - Installation)
and drill thread holes
→See "Owner's Manual - Installation"
2. Mount a hook screw, etc. on ceiling beams or structural materials
and hook the anti-falling wire to it.
3. Use 2 commercially available screws to mount the camera
Note:
The screws of 4mm diameter must be long enough to mount the camera.•
456-00
Printed in China
Tamron co., Ltd. Industrial Optics Business Unit
1385, Hasunuma, Minuma-ku, Saitama-shi, Saitama 337-8556 JAPAN
Tel: [phone] Fax: [phone] E-mail [email protected]
EN300QV-P-CMA4Sheet.indd2EN300QV-P-CMA4Sheet.indd2 2013/04/2213:22:032013/04/2213:22:03