Tannoy Di series User manual

Di5, Di5t,
Di5 DC & Di5 DCt
Di6, Di6t,
Di6 DC & Di6 DCt
Di8 DC & Di8 DCt
THE
RANGE
USERMANUAL
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 1

2
INTRODUCTION
SAFETY INSTRUCTIONS
PRODUCT IDENTIFICATION
STANDARD AND OPTIONAL ACCESSORIES
INSTALLATION GUIDELINES
6 Installation using supplied yoke bracket
7 Installation using optional K-BallTM bracket
8 Installation using supplied yoke bracket with optional pole-mount adaptor
9 Installation using optional K-BallTM bracket with optional pole-mount adaptor
PRODUCT DIMENSIONS
HARDWARE DIMENSIONS
TECHNICAL SPECIFICATIONS
12 Di ICT specifications
13 Di Dual ConcentricTM specifications
WARRANTY STATEMENT
DECLARATION OF CONFORMITY
3
3
4
5
6-9
10
11
12-13
14
15
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 2

3
Designed for a wide variety of sound reinforcement applications the Tannoy Di is an ultra compact loudspeaker system
capable of delivering high sound pressure levels with extremely low distortion, resulting in outstanding clarity, definition and
detail. A truly universal solution, the Di offers outstanding durability and resistance to scuffs and knocks. Able to deliver
consistent performance under a wide range of adverse conditions the Di is suited to applications indoors or out, whether it be
a theme bar or theme park. Available in black or white the Di will effectively blend into most backgrounds. Utilisation of the
point source loudspeaker allows the Di to be mounted on a wall or ceiling in either horizontal or vertical orientations without
affecting its performance. A range of hardware options ensures simple and effective installation. Also available with built in
line transformer.
For applications requiring extended low frequency enhancement, a range of Tannoy sub-bass systems are available and can
be used in conjunction with the Di.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. The user is responsible for fixing the hardware to the surface to ensure safe operation. The fixings must support the
weight of the product – please consult the manual’s specification page for the appropriate weights. Please consult the
relevant construction codes in your region for further information on suitable hardware fixing methods.
6. Some regional construction codes require the use of a secondary method of securing loudspeakers to surfaces to provide
security of a back-up support. A secondary support line should be attached from the safety loop on the rear of the product
to a source point on the wall. Please consult the relevant construction codes in your region.
7. Tannoy will not be held accountable for any damage caused by incorrect installation.
THE USERMANUAL
RANGE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 3

4
YOKE TRIM
Remove the yoke trims on the top
and bottom panels to access the
yoke bracket fixing point
GRILLE TRIM
Lift the grille trim back using the
tab to access the transformer
tapping switch on transformer
models.
INPUT CONNECTOR
Remove the rubber grommet to
access the connector. The
rubber grommet ensures the rear
of the product is kept water-tight
SAFETY TAB
GRILLE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 4

5
GRILLE
GRILLE TRIM
YOKE BRACKET
(SUPPLIED WITH
FIXINGS)
K-BALLTM BRACKET
POLE MOUNT ADAPTOR
THE USERMANUAL
RANGE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 5

6
USING SUPPLIED YOKE BRACKET
1. Fix the yoke bracket
to the surface using a
suitable fixing method.
2. Remove the yoke
trims from the product
to access the bracket
fixing points.
4. Feed the speaker
cable through the rubber
grommet then connect
the euro-type plug to the
wires, observing the
correct polarity.
5. For connection to the
loudspeaker, use pins
1 (+) and 2 (-).
Pins 3 (-) and 4 (+) are
in parallel for connection
to additional speakers in
a distributed line.
6. Offer the speaker up
to the bracket and
attach it using a 5mm
alan key and supplied
fixings.
7. Connect the euro
plug then replace the
rubber grommet to
ensure the speaker is
watertight.
8. Connect a secondary
support line to the
safety tab at the rear of
the cabinet.
9. Lift the grille trim
using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found on
the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.
TRANSFORMER
MODELS ONLY
TRANSFORMER
MODELS ONLY
TRANSFORMER
MODELS ONLY
10. The Di5t and Di5
DCt models are fitted
with 30W transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
11. The Di6t, Di6 DCt,
& Di8 DCt models are
fitted with 60W
transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
3. Remove the rubber
grommet from the rear of
the speaker. Inclusion of
the rubber grommet is
only required if installing
the product outdoors.
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 6

7
5. Offer the speaker up
to the K-BallTM Bracket.
Push the speaker onto
the bracket to engage
the euro plug.
6. Fit the rubber
grommet and finger-
tighten the bracket bolt
while supporting the
speaker. If the
connector has engaged
properly the speaker
will lock onto the
bracket
7.Swivel the speaker
into position then use
a 19mm wrench to give
another half turn to
ensure the speaker is
locked in position.
8. Connect a secondary
support line to the
safety tab at the rear of
the cabinet.
9. Lift the grille trim
using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found on
the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.
TRANSFORMER
MODELS ONLY
TRANSFORMER
MODELS ONLY
TRANSFORMER
MODELS ONLY
10. The Di5t and Di5
DCt models are fitted
with 30W transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
11. The Di6t, Di6 DCt,
& Di8 DCt models are
fitted with 60W
transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
1. If attaching the
K-BallTM bracket to a
conduit junction box
(J-box), pass the
speaker wire through the
bracket adaptor plate
then attach the adaptor
plate to the conduit
junction box using the
fixings provided.
2. Connect the speaker
wires to the connector
block in the bracket.
For connection to an
amplifier use pins 1 (+)
and 2 (-)
Pins 3 (-) and 4 (+) are
in parallel for
connection to additional
speakers in a
distributed line.
3. If a conduit junction
box has been used,
offer the bracket up to
the adaptor plate, with
the foam gasket**
squeezed in between.
Attach the bracket to
the surface using a
suitable fixing method*.
4. If you are attaching
the bracket directly to a
surface, offer the
bracket up to the
surface with the foam
gasket** squeezed in
between. Attach the
bracket to the surface
using a suitable fixing
method*.
NOTE
* See safety notices on
page 3
** The foam gasket &
rubber grommet is
intended to provide a
water tight seal.
Inclusion of the foam
gasket & grommet is
only a requirement if
installing outdoors.
USING OPTIONAL K-BALLTM BRACKET
THE USERMANUAL
RANGE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 7

8
IUSING OPTIONAL POLE MOUNT ADAPTOR
IWITH SUPPLIED YOKE BRACKET
2. Fix the pole mount
bracket adaptor to the
pole using the strapping
provided. The bracket
can be mounted in
portrait or landscape
orientations.
3. Remove the yoke
trims from the product
to access the bracket
fixing points.
4. Remove the rubber
grommet from the rear
of the speake. Inclusion
of the rubber grommet is
only required if installing
the product outdoors.
5. Feed the speaker
cable through the rubber
grommet then connect
the euro-type plug to the
wires, observing the
correct polarity.
6. For connection to the
loudspeaker, use pins
1 (+) and 2 (-)
Pins 3 (-) and 4 (+) are
in parallel for
connection to additional
speakers in a
distributed line.
7. Offer the speaker up
to the bracket and
attach it using a 5mm
alan key and supplied
fixings.
8. Connect the euro
plug then replace the
rubber grommet to
ensure the speaker is
watertight.
9. Connect a secondary
support line to the safety
tab at the rear of the
cabinet.
TRANSFORMER
MODELS ONLY
TRANSFORMER
MODELS ONLY
10. Lift the grille trim
using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found
on the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.
11. The Di5t and Di5
DCt models are fitted
with 30W transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
TRANSFORMER
MODELS ONLY
12. The Di6t, Di6 DCt,
& Di8 DCt models are
fitted with 60W
transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
1. Use the supplied
fixings to fix the yoke
bracket to the pole
bracket adaptor.
Note that the Di5 models
require 2 fixing screws
whereas the Di6 and Di8
models require 4 fixing
screws.
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 8

9
5. Remove the rubber
grommet from the rear of
the speaker then offer
the speaker up to the K-
BallTM Bracket.
7.Connect a secondary
support line to the
safety tab at the rear of
the cabinet.
8. Lift the grille trim
using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found
on the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.
9. The Di5t and Di5 DCt
models are fitted with
30W transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
TRANSFORMER
MODELS ONLY
TRANSFORMER
MODELS ONLY
10. The Di6t, Di6 DCt,
& Di8 DCt models are
fitted with 60W
transformers.
THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.
1. Pass the speaker wire
through the pole-mount
adaptor plate then fix the
pole mount bracket
adaptor to the pole using
the strapping provided.
The bracket can be
mounted portrait or
landscape orientations.
2. Connect the speaker
wires to the connector
block in the rear of the
K-BallTM bracket.
For connection to an
amplifier use pins 1 (+)
and 2 (-).
Pins 3 (-) and 4 (+) are
in parallel for
connection to additional
speakers in a
distributed line.
3. Offer the K-BallTM
bracket up to the
adaptor plate, with the
foam gasket**
squeezed in between.
Use the supplied fixings
to fix the K-BallTM
bracket to the pole
bracket adaptor.
4. Fix the pole mount
bracket adaptor to the
pole using the strapping
provided. The bracket
can be mounted in
portrait or landscape
orientations.
6. Finger-tighten the
bracket bolt to extend
the bracket out to
connect with the euro
plug socket. Position
speaker then use a
19mm wrench to give
another half turn to
ensure the speaker is
locked in position.
NOTE
** The foam gasket &
rubber grommet is
intended to provide a
water tight seal.
Inclusion of the foam
gasket & grommet is
only a requirement if
installing outdoors.
TRANSFORMER
MODELS ONLY
USING POLE MOUNT ADAPTOR
WITH OPTIONAL K-BALLTM BRACKET
THE USERMANUAL
RANGE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 9

10
Di5
Di6
Di8
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 10

65.0
[2.56"]
180.0
[7.09"]
R15.0
[R0.59"]
Di6 YOKE
11
241.0
[9.49"]
123.0
[4.84"]
54.0
[2.13"]
R15.0
[R0.59"] 85.0
[3.35"]
90.0
[3.54"]
6.0
[0.24"]
?22.0
[?0.87"]
35.0
[1.38"]
358.0
[14.09"]
Di6 YOKE
145.0
[5.71"]
150.0
[5.91"]
35.0
[1.38"]
6.0
[0.24"]
?22.0
[?0.87"]
Di6 YOKE
[2.56"]
Di6 YOKE
R15.0
[R0.59"]
217.0
[8.54"]
70.0
[2.76"]
Di8 YOKE
406.0
[15.98"]
165.0 170.0
Di8 YOKE
47.7
[1.88"]
137.9
[5.43"]
93.2
[3.67"]
155.0
[6.10"]
65.0
[2.56"]
165.0
[6.50"]
170.0
[6.69"]
35.0
[1.38"]
R11.0
[R0.43"]
[
Di8 YOKE
Di8 YOKE
5” YOKE BRACKET
6” YOKE BRACKET
8” YOKE BRACKET
K-BALLTM BRACKET
THE USERMANUAL
RANGE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 11

12
Di5 Di6
SYSTEM
Frequency Response (-3dB) (1) 90Hz - 25kHz 75Hz - 22kHz
Frequency Range (-10dB) (1) 80Hz - 30kHz 55Hz - 24kHz
System Sensitivity (1W @1m) (2) 88dB 90dB
1W = 2.45V for 6 Ohms
Dispersion 90 90
Degrees conical -6dB
Low Frequency Driver 1x 110mm (4.50”) 1x 165mm (6.50”)
Mineral loaded polypropylene
High Frequency Driver ICTTM ICTTM
Crossover 7kHz 7kHz
Inductively Coupled ICT™
Directivity Factor (Q) 1kHz to 10kHz 5.3 averaged 10.5 averaged
Directivity Index (DI) 1kHz to 10kHz 6.6 averaged 8.4 averaged
Rated Maximum SPL (2) Average 105dB 107dB
Peak 111dB 113dB
Power Handling Average 50W 60W
Programme 100W 120W
Peak 200W 240W
Recommended Amplifier Power 100W @ 6 Ohms 120W @ 6 Ohms
Nominal Impedance 6 Ohms 6 Ohms
Distortion 10% Full Power (5.5V) 2nd Harmonic 3rd Harmonic (6.0V) 2nd Harmonic 3rd Harmonic
250Hz 2.00% 0.26% 1.86% 0.12%
1kHz 0.53% 0.19% 1.17% 0.54%
10kHz 2.50% 0.35% 1.10% 0.04%
Distortion 1% Full Power (1.73V) 2nd Harmonic 3rd Harmonic (1.9V) 2nd Harmonic 3rd Harmonic
250Hz 0.65% 0.09% 0.70% 0.14%
1kHz 0.144% 0.11% 0.45% 0.39%
10kHz 0.52% 0.298% 0.25% 0.065%
CONSTRUCTION
Enclosure Weather resistant high impact polystyrene (HIPS), IP64 to EN60529 (IEC529)
Grille Steel, with weather resistant coating
Finish Textured black or white paint with matching rubber trims
Factory fitted custom trim colours available to special order
Connectors Removable locking Euroblock type connector
with screw terminals and "loop through" facility
Fittings 1 x socket for K-Ball™ bracket and 2 x M8 yoke bracket inserts
Supplied Accessory Yoke bracket
Dimensions 240.7 x 155.0 x 162.0mm 357.5 x 230.0 x 223.2mm
9.47 x 6.10 x 6.38” 14.08 x 9.05 x 8.79”
Weight 2.2kg (4.85lbs) 3.7kg (8.15lbs)
TRANSFORMER VERSIONS Di5t Di6t
Specifications as above except:
Transformer Taps 70V
30W / 15W / 7.5W / 3.75W / OFF 60W / 30W / 15W / 7.5W / OFF
Rotary switch & Low Impedance operation & Low Impedance operation
mounted under trim
100V
30W / 15W / 7.5W / OFF & 60W / 30W /15W / OFF &
Low Impedance operation Low Impedance operation
Rated Maximum SPL (2) Average 103dB (using 30W transformer tap) 107dB (using 60W transformer tap)
Weight 2.7kg (5.94lbs) 5.0kg (11.02lbs)
See Passive models above for max SPL figures on low impedance settings.
ICTTM MODELS
Notes:
(1) Average over stated bandwidth. Measured at 1 metre on axis in an anechoic chamber
(2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, and EaseTM Data can be downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications,
which Tannoy reserves the right to alter without prior notice.
*
*
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 12

Di5 DC Di6 DC Di8 DC
SYSTEM
Frequency Response (-3dB) (1) 90Hz - 50kHz 75Hz - 30kHz 65Hz - 30kHz
Frequency Range (-10dB) (1) 80Hz - 54kHz 55Hz - 35kHz 53Hz - 35kHz
System Sensitivity (1W @1m) (2) 88dB 89dB 91dB
1W = 2.83V for 8 Ohms
Dispersion 90 90 90
Degrees conical -6dB
Low Frequency Driver 1x 110mm (4.50”) 1x 165mm (6.50”) 1x 200mm (8.00”)
Dual ConcentricTM constant directivity driver
with a resin treated multi fibre paper pulp cone
High Frequency Driver 19mm (0.75”) 25mm (1.00”) 25mm (1.00”)
titanium dome with neodymium magnet system
Crossover 2kHz - 2nd order LF, 1.6kHz - 2nd order LF, 1.5kHz - 2nd order LF,
2nd order HF with 2nd order HF with 2nd order HF with
Dynamic HF protection Dynamic HF protection Dynamic HF protection
Directivity Factor (Q) 1kHz to 10kHz 5.3 averaged 5.6 averaged 5.5 averaged
Directivity Index (DI) 1kHz to 10kHz 6.6 averaged 7.0 averaged 7.0 averaged
Rated Maximum SPL (2) Average 106dB 109dB 111dB
Peak 112dB 115dB 117dB
Power Handling Average 60W 90W 90W
Programme 120W 180W 180W
Peak 240W 360W 360W
Recommended Amplifier Power 120W @ 8 Ohms 180W @ 8 Ohms 180W @ 8 Ohms
Nominal Impedance 8 Ohms 8 Ohms 8 Ohms
Distortion 10% Full Power (6.9V) 2nd Harmonic 3rd Harmonic (8.0V) 2nd Harmonic 3rd Harmonic (8.5V) 2nd Harmonic 3rd Harmonic
250Hz 4.00% 0.20% 1.00% 0.32% 1.55% 0.42%
1kHz 0.76% 0.60% 0.18% 0.32% 0.41% 0.63%
10kHz 0.65% 0.15% 1.00% 0.18% 1.20% 0.65%
Distortion 1% Full Power (2.2V) 2nd Harmonic 3rd Harmonic (2.5V) 2nd Harmonic 3rd Harmonic (2.7V) 2nd Harmonic 3rd Harmonic
250Hz 2.00% 0.15% 0.25% 0.25% 0.43% 0.48%
1kHz 0.009% 0.124% 0.06% 0.18% 0.07% 0.47%
10kHz 0.32% 0.17% 0.45% 0.14% 0.55% 0.13%
CONSTRUCTION
Enclosure Weather resistant high impact polystyrene (HIPS), IP64 to EN60529 (IEC529)
Grille Steel, with weather resistant coating
Finish Textured black or white paint with matching rubber trims
Factory fitted custom trim colours available to special order
Connectors Removable locking Euroblock type connector
with screw terminals and "loop through" facility
Fittings 1 x socket for K-Ball™ bracket and 2 x M8 yoke bracket inserts
Supplied Accessory Yoke bracket
Dimensions 240.7 x 155.0 x 162.0mm 357.5 x 230.0 x 223.2mm 404.3 x 260.0 x 260.3mm
9.47 x 6.10 x 6.38” 14.08 x 9.05 x 8.79” 15.92 x 10.24 x 10.25”
Weight 2.2kg (4.85lbs) 5.0kg (11.02lbs) 6.0kg (13.23lbs)
TRANSFORMER VERSIONS Di5 DCt Di6 DCt Di8 DCt
Specifications as above except:
Transformer Taps 70V
30W / 15W / 7.5W / 3.75W / OFF 60W / 30W / 15W / 7.5W / OFF 60W / 30W / 15W / 7.5W / OFF
Rotary switch & Low Impedance operation & Low Impedance operation & Low Impedance operation
mounted under trim
100V
30W / 15W / 7.5W / OFF & 60W / 30W / 15W / 7.5W / OFF 60W / 30W / 15W / OFF &
Low Impedance operation Low Impedance operation Low Impedance operation
Rated Maximum SPL (2) Average 106dB (103dB - 30W transformer tap) 109dB (107dB - 60W transformer tap) 111dB (109dB - 60W transformer tap)
Weight 2.7kg (5.95lbs) 5.5kg (12.12lbs) 7.0kg (15.87lbs)
See Passive models above for max SPL figures on low impedance settings.
DUAL CONCENTRICTM MODELS
Notes:
(1) Average over stated bandwidth. Measured at 1 metre on axis in an anechoic chamber
(2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, and EaseTM Data can be downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications,
which Tannoy reserves the right to alter without prior notice.
*
*
13
THE USERMANUAL
RANGE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 13

14
No maintenance of the Di loudspeaker is necessary.
All of our products have been produced and tested with care and precision to give first-class service.
All passive components are guaranteed for a period of five years from the date of purchase from an authorised Tannoy dealer
subject to the absence or evidence of misuse, overload, or accidental damage.
All active and electronic components are guaranteed for a period of one year from the date of purchase from an authorised
Tannoy dealer subject to the absence of, or evidence of, misuse, overload or accidental damage.
If at any time during this warranty period the equipment proves to be defective for any reason other than accident, misuse,
neglect, unauthorised modification or fair wear and tear, we will repair any such manufacturing defect or, at our option, replace it
without charge for labour, parts or return carriage.
If you suspect a problem with a Tannoy product then, in the first instance, discuss it with your Tannoy dealer. If you require further
assistance then we ask that you deal directly with your local Tannoy distributor. If you cannot locate your distributor please contact
Customer Services, Tannoy Ltd at the address given below.
Customer Services, Tannoy Ltd., Rosehall Industrial Estate, Coatbridge, Strathclyde ML5 4TF, Scotland
Telephone: [phone] (National)
[phone] (International)
Fax: [phone] (National)
[phone] (International)
E-mail: [e-mail]
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
Our policy commits us to incorporating improvements to our products through continuous research
and development. Please confirm current specifications for critical applications with your supplier.
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 14

15
The following apparatus is manufactured in China for Tannoy Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF
and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives
relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic
disturbances generated do not exceed levels allowing radio and telecommunications equipment and other apparatus to
operate as intended, and, the apparatus has an adequate level of intrinsic immunity to electromagnetic disturbance to enable
operation as specified and intended.
Details of the Apparatus: Tannoy Contractor Loudspeaker
Model Number: Di
Associated Technical File: EMCi6
Applicable Standards: EN 50081-1 Emission
EN 50082-1 Immunity
Signed:
Position: Director of Engineering (Professional)
Date: 11th Dec. 06
THE USERMANUAL
RANGE
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 15

Tannoy United Kingdom T: 00 44 (0) 1236 420199 E: [email protected]
Tannoy North America T: 00 1 [phone] E: [email protected]
Tannoy Deutschland T: 00 49 (180) 1111 881 E: [email protected]
Tannoy France T: 00 33 (0)1 7036 7473 E: [email protected]
Tannoy adopts a policy of continuous improvement and product specification is subject to change.
REVISION DATE: 5 Feb ‘07 6481 0471 02/06
Di Manual 8-2-07 AW:Layout 1 13/2/07 12:59 Page 16