Tanova TDS30 User manual

Use in conjunction with full size template supplied with your unit
For further assistance in New Zealand
www.tanova.co.nz or www.fit-nz.co.nz or contact Fit 0800 852 258
STEP BY STEP INSTALLATION INSTRUCTIONS
FOR ALL DESIGNER SERIES
KITCHEN WASTE & LAUNDRY UNITS
For further assistance in Vict, SA & Tas, contact 1300 121 800
For further assistance in NSW, QLD, NT, ACT and WA, contact 1300 222 600
www.tanova-nz.com

RUNNER POSITIONS are on each short end of the template provided, marked 1RHF and 1 LHF
1. Hold Template against the underside of the cabinet top rail and 1 RHF flush with the right-hand cabinet side,
and mark runner fixing positions as shown on template.
2. Repeat on le hand side of cabinet using the 1 LHF edge of template.
3. Fix Runners to cabinet THROUGH TOP ROW OF HOLES IN RUNNERS using either 3 x M6 x 11 Euro Screws
(Pre-drill with 5mm) or 3 x 6g x 15mm wood screws (Pre-drill with 3mm) per tab minimum.
4. Position Top Cover against the top of the cabinet and 3mm back from the front, screw off with the 8g x 15mm
Pan screws. Note: Top Cover only supplied standard with waste systems.
5. Extend runners out the front of cabinet. Slide bin frame onto runners and engage tabs at rear, push bin assembly
on firmly until the front connection “Clicks” into place.
DESIGNER SERIES
INSTALLATION INSTRUCTIONS
USE IN CONJUNCTION WITH THE FULL SIZE TEMPLATE SUPPLIED WITH YOUR UNIT
STEP 1
STEP 2 DRAWER FRONT TEMPLATE is on the long edge of the template provided, marked 2 Centre Top.
6. On the back of the drawer front, mark the Center line of the drawer front. Measure down from the top of the
drawer front the desired amount of Cabinet overlay.
7. Align the template center marks with the marked drawer front center line.
8. Move template upwards until flush with overlay position, mark drawer lower bracket and gallery rail fixing
points and fit drawer and gallery rail connector brackets with the 6 x 6g x 15mm countersunk screws.
NOTE: If you have a LOWSIDE TDS80 system to suit 800 Cabinet, take notice of the offset LH and RH centerline
points,
“Centre TDS80LH” and “Centre TDS80RH”
9. Fit drawer front to drawer connector brackets.
Drawer Insertion
Drawer Front Assembly & Removal
Screw-on
Assembly ‘Click’ Removal

10. Loosen lock off screw, access sideways and height adjustment screws through the side of the drawer.
11. Adjust drawer front tilt on the gallery rail thread.
12. Ensure adjustment lock off screw is tightened, and gallery rail cap clipped on.
13. Fit cover cap to drawer side.
14. insert buckets or laundry hamper to system.
STEP 3
Drawer Front - Side Adjustment
Drawer Front - Height Adjustment
Drawer Front Tilt Adjustment
To right
Adjustable by 1.25mm to the le
To le
Adjustable by 1.25mm to the right
Loosen Tighten
±1.8mm
Rectangular Rail Round Rail

HIGHSIDE A B C D E
TDS30 212mm 308mm 340mm 338mm 118.5mm
TDS35H 252mm 348mm 380mm 378mm 143.5mm
TDS40 212mm 308mm 340mm 338mm 168.5mm
TDS40-C 252mm 348mm 380mm 378mm 168.5mm
LAUNDRY
TDS35L 134mm 230mm 262mm 259mm 143.5mm
TDS40L 125mm 221mm 253mm 251mm 168.5mm
TDS60L 170mm 266mm 298mm 296mm 268.5mm
TDS45L 125mm 221mm 253mm 251mm 193.5mm
LOWSIDE
TDS35 100mm 196mm 228mm 226mm 143.5mm
TDS45-50 100mm 196mm 228mm 226mm 193.5mm
TDS45 100mm 196mm 228mm 226mm 193.5mm
TDS60 100mm 196mm 228mm 226mm 268.5mm
TDS80 100mm 196mm 228mm 226mm 368.5mm
TEMPLATE DIMENSIONS
RUNNER IMAGE WITH DIMENSIONS
KEY
A= Gallery rail to top
B= Front connector Top fix to top
C= Front connector Btm fix to top
D= RH and LH Runner to top
E= Centreline to front fix vertical
450mm
500, 550mm
600, 650mm
A FULL SIZE TEMPLATE, SIMILAR TO THE IMAGE
SEEN HERE, IS SUPPLIED WITH YOUR UNIT.
THESE INSTRUCTIONS ARE TO BE USED IN
CONJUNCTION WITH THAT TEMPLATE.
11
2Centre
TDS80 LH
Centre
TDS80 RH
TDS35
TDS80RH
TDS45
TDS45-50 TDS60
TDS35
TDS80LH
TDS45
TDS45-50
TDS60
1
RH
1
LH
LHF RHF
Centre Top
37
224
BA
Drilling Dimensions from underside of Cabinet Top Rail (mm)
Model A B C D E
TDS35 100 196 228 226 143.5
TDS45 100 196 228 226 193.5
TDS45-50 100 196 228 226 193.5
TDS60 100 196 228 226 268.5
TDS80 100 196 228 226 368.5
D
E
C
96
32
TDS LOWSIDE TEMPLATE
KEY
A = Gallery rail to top
B = Front connector Top fix to top
C = Front connector Btm fix to top
D = RH and LH Runner to top
E = Centreline to front fix vertical