Target Furniture ALFDS100WKD User manual

Job no.
1000 Wide Shelf Desk
INSTRUCTION MANUAL

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
1
30Min
Approximate Assembly Time
1 Person Assembly
Floor Area 3m
x 2m
Required Assembly Space
Tools Required
Assembly Details

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
2
1. For the protection of your furniture, we recommend that the product is
placed on a protected surface during assembly to prevent damage
2. Please check that all parts are present before you start the assembly of
your furniture
3. For ease and speed of assembly, we recommend that you identify all the
parts required for each step before commencing with assembly
4. For larger items, please ensure that you have sufficient space (as
indicated on page 1)
5. We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily
6. During Assembly please take care not to over-tighten hardware as this
may damage the product
7. Always place the product on a steady and stable surface
8. Do not use the product as a stepladder
9. This product is intended for indoor, household use only as it is a non-
industrial product
✓Please periodically check all things and re-tighten as necessary
✓To clean your item, please use a damp cloth and wipe clean
✓Never allow any kind of liquid on your furniture
✓Please do not place hot items (eg. Hot drinks) directly on to the surface
Tips before you start
Care and Maintenance

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
3
QTY
PART
MEASUREMENTS
NOTES
1
Top
1000 x 500 x 25mm
Laminate on one side.
1
LH End
745 x 396 x 25mm
Laminate on both sides.
1
RH End
745 x 396 x 25mm
Laminate on both sides.
1
Modesty
390 x 944 x 15mm
Laminate on both sides.
1
Shelf
366 x 944 x 15mm
Laminate on one side.
Parts List
Hardware List
14 x
Connecting
Bolts
15 x Large
Cams
(15mm)
8 x Dowels
4 x Nail on
Glides
8 x Stick-on
Cam Covers

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
4
The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this
system works.
Cam Installation & Operation Guide

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
5
•To begin assembly, lay the top finished side down on a clean and clear surface
•Screw four Connecting Bolts into the holes as shown
•Insert two Large Cams as shown (make sure the arrow on the top of the Cam points towards the
top edge of the End).
•Push two Dowels into the top edge of the End
•Screw four Connecting Bolts into the holes as shown
•Tap the two Nail on Glides into the bottom of the Ends as indicated below. Space them about
50mm in from the front and back edges.
Assembly
STEP 1: Top
STEP 2: LH End
Connecting Bolt
Connecting Bolt
Large Cam
Dowel
Nail on Glide
Connecting Bolts
Connecting Bolts
Dowels
Cams
Nail on Glides

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
6
•Repeat the previous steps to install the hardware in the RH End.
•Install four Large Cams into the Modesty as shown below (ensure the arrow on the top of the Cam
points towards the edge.
•Install the two Connecting Bolts as indicated below.
STEP 3: RH End
STEP 4: Modesty
Large Cam
Connecting Bolt
Large Cam
Dowel
Nail on Glide
Connecting Bolt
Nail on Glides
Connecting Bolts
Cams
Dowels
Cams
Cams
Connecting Bolts

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
7
•Attach the Shelf to the Modesty by fitting the Connecting Bolts with the corresponding pre-drilled
holes as shown below.
•Lock the pieces together by turning the Cams ¼ - ½ of a turn in a clockwise direction.
•Attach the LH End by fitting the Connecting Bolts with the corresponding pre-drilled holes as shown
below.
•Once again, lock the pieces together by turning the Cams ¼ - ½ of a turn in a clockwise direction.
STEP 5: Attach the Shelf to the Modesty
STEP 6: Attach the LH End
Shelf
Modesty

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
8
•Attach the RH End by fitting the Connecting Bolts with the corresponding pre-drilled holes as shown
below.
•Lock the pieces together by turning the Cams ¼ - ½ of a turn in a clockwise direction.
•Stand the desk upright and place the Top on ensuring the larger overhang is at the back of the
ends.
•Lock the pieces together by turning the Cams ¼ - ½ of a turn in a clockwise direction.
•Then put the finishing touch on your desk by using the cover stickers provided to cover the cams
were visible.
STEP 7: Attach the RH End
STEP 8: Attach the Top