Tasseron Q-Duct SAFE User manual

HUMIDITY SENSORS

SAFEBOXHANDLINGNOTES–PLEASEREADFIRST
ToOpen:1.Depressbottomlatchwithaslottedscrewdriverandlidwillpopout.2.Pulltopoflidstraightoutfrom
housingwithoutliftingup.3.Onceentirelypulledout,liftlidanditwillremaininopenpositionuntilclosed.
ToClose:1.Pushliddownwithoutlatchingbottom.2.Pushintophingesuntilitsnapsintoplace.3.Closebottomuntilit
latches.4.Optionalscrewprovidedtomorepermanentlysecurelidtohousing.
MountingInstructions:

Step1–Drill15/16”holeindesiredlocationinduct.


Step2–Alignopeninginmountingflangewithholein
ductandattachmountingflangetoductusingself‐
tappingscrews.





Step3‐Insertsensorprobeinmountingflangeandpushuntilsensorsnapsintoplace.Wirethroughprovidedbottomor
sideaccesspoints.Additionalsnap‐inconduitadaptersavailableifnecessary.ProceedtoConfigurationInstructions.






Step1–Determinewiringlocation(northsideof
buildingifpossible).Drillhole,ifnecessary,thencenter
andattachthemountingflangetobuilding.  
Step2‐Ifwiringfromrear,feedwirefromholeintothe
rearaccesspointonthesensor.Snapsensoronto
mountingflange.




Step3–Ifwiringthroughsideaccesspoints,piercegrommetwithknifeorremoveandsnapinconduitadapter.
Additionalconduitadaptersavailableifnecessary.ProceedtoConfigurationInstructions.

INSTALLATIONINSTRUCTIONS

Step1–Feedwiresthroughholein
rearofsensor.
Step2‐Mountwithscrews,then
makeconnections.












ConfigurationInstructionsforALLTasseronHumiditySensors:
Foroptionalpassivetemperaturesensor,connectonewiretoeachquickconnectterminallabeled“TEMP”(non‐polar).
Instructionsfor4to20mAOutputDIPSwitchConfiguration
TerminalFunction
TEMP2‐poleconnectionforoptionalpassivetemperaturesensor(no polarity)
VINMainpower–24VDCpowersupplyrecommended
4‐20mACurrentmodesignaloutput
COM(notusedincurrentmode)
VOUT(notusedincurrentmode)

Step1–BesurethewhiteOutputmodeDIPswitchesareintheproperconfiguration.For4‐20mAoutput,DIPswitch#2
mustbeintheRIGHTposition.Switch#1hasnofunctioninthismode.
Step2–Terminatecontrolwiresinquickconnectsasindicatedinthetableabove.Only2wiresareneededfor4‐20mA
outputmode;mainpowersupplyandsignaloutput.Thesewiresterminateat“VIN”and“4‐20mA”.
Step3–Poweroncontrol.
Instructionsfor0‐5Vor0‐10VOutputDIPSwitchConfiguration
TerminalFunction
TEMP2‐poleconnectionforoptionalpassivetemperaturesensor(nopolarity)
VINMainpower–24VDCpowersupplyrecommended
4‐20mA(notusedinvoltagemode)
COMCommon
VOUTVoltagesignaloutput
 0‐5VOutput0‐10VOutput
Step1–BesurethewhiteOutputmodeDIPswitchisintheproperconfiguration.For0‐5Voutput,DIPswitch#1mustbe
intheLEFTpositionandDIPswitch#2mustbeintheRIGHTposition.For0‐10Voutput,both#1and#2DIPswitchesmust
beintheRIGHTpositions.
Step2–Terminatecontrolwiresinquickconnectsasindicatedinthetableabove.ThreewiresareneededforVoltage
outputmode;mainpowersupply(VIN),Common(COM),andsignaloutput(VOUT).
Step3–Poweroncontrol.

140ChoateCircle▪Montoursville,PA17754▪570.601.1971
[e-mail]▪www.tasseronusa.com
Step3–Snaponcover.Depress
hooksthroughventswithtool
toremove.