Taylor Made KW Series User manual

FLAGPOLE MOUNT
Aftermarket Manual
Patent Pending

2
Rev: 02.18.21 CCD-0004215
Introduction
The flagpole mount is attached to a boat’s ski bar for display of a flag.
Additional information about this product and replacement kits can be
obtained from taylormadeproducts.com.
Table of Contents
Introduction .......................................................... 2
Safety ................................................................. 3
Parts List .............................................................. 4
Resources Required ................................................. 4
Installation ............................................................ 5
Operation ............................................................. 7
Flagpole Mount KitFlagpole Mount Kit
Part #Part # DescriptionDescription
943 Flagpole mount with fastening hardware

3
CCD-0004215 Rev: 02.18.21
Safety
Read and fully understand all instructions before installing or operating
this product. Adhere to all safety labels. This manual provides general
instructions. Many variables can change the circumstances of the
instructions, i.e., the degree of difficulty, operation and ability of the
individual performing the instructions.
This manual cannot begin to plot out instructions for every possibility but
provides the general instructions, as necessary, for effectively interfacing
with the device, product or system.
Failure to correctly follow the provided instructions may result in death,
serious personal injury, severe product and/or property damage,
including voiding of the LCI limited warranty.
DO NOT SIT OR STAND ON THE FLAGPOLE MOUNT.
DO NOT USE THE FLAGPOLE MOUNT TO TOW ANOTHER BOAT
OR ANY OTHER APPARATUS.
DO NOT USE THE FLAGPOLE MOUNT AS A HAND GRAB BAR TO
PULL A SWIMMER ONTO THE BOAT.
WHEN PULLING A SKIER OR A TUBE, MAKE SURE THE FLAG
INSERTED INTO THE FLAGPOLE MOUNT IS NOT TOO LARGE.
IF THE FLAG IS TOUCHING THE SKI ROPE, THE FLAG MUST BE
REMOVED.

4
Rev: 02.18.21 CCD-0004215
A
G
I
H
E
D
B
F1
F2
F3
Parts List
J
TaylorMade KW Series Flagpole Mount Kit PN 943
Part Part # Description Qty
A 2021011867 Lower clamp brackets 2
B 2021011868 Mount main body 1
C1 2021011877 Rubber compression insert, 0.75 1
C2 2021011876 Rubber compression insert, 1.00 1
C3 2021011875 Rubber compression insert, 1.25 1
D 2021011874 Knob 1
E 2021011872 Flagpole coupler 1
F1 2021011881 SS machine screws for 1 1/2" OD tubing, M10x35 3
F2 2021011880 SS machine screws for 2" OD tubing, M10x55 3
F3 2021011878 SS machine screws for 2 1/2" OD tubing, M10x70 3
G 2021011883 SS machine screw for coupler, M10x25 1
H 2021011884 Hex wrench 1
I 2021011887 Miniature disposable level 1
J 2021011889 Template to measure ski bar diameter 1
C1
C2
C3

5
CCD-0004215 Rev: 02.18.21
Installation
1. Assemble Steps 1 to 5 on dry land to avoid possibly dropping parts
into the open water.
2. Use the enclosed cardboard template (Fig.1) to measure the outer
diameter of the ski bar and to determine the correct machine screw length.
3. Place the agpole coupler — the part that holds the agpole — onto
the top of the mount.
NOTE: Make sure to align the two slots on the top of the mount
(Fig.2A) to the bottom of the coupler (Fig.2B).
4. Insert the smallest machine screw (Part G), M10x25 (Fig.3A), through
the main body and into the underside of the coupler (Fig.3B). Using the
included hex wrench, tighten rmly but do not overtighten.
Fig.1
Fig.2 Fig.3
B
A
5. Use the mini level (Fig.4) to ensure the agpole holder is level when
attached to the ski bar. Remove the self-adhesive backing then a󰀩x the
level to the at top side of the mount. Remove when nished mounting
the agpole holder.
Fig.4
B
A

6
Rev: 02.18.21 CCD-0004215
Fig.5
Fig.6
6. Based on the outer diameter of the ski bar, determine which set of
machine screws to use to attach the lower clamp brackets to the mount.
Size options include: F1, M10x35; F2, M10x55; and F3, M10x70.
7. Orient the mount so the top leading edge of the angled portion faces
out (Fig.5).
8. Using the correct machine screw length, insert all four machine
screws through holes in the base of the mount (Fig.6).
9. Hold one lower clamp bracket underneath and nger tighten two
machine screws into the clamp bracket. Repeat this step for the
remaining bracket.
10. Finish tightening the four machine screws using the included hex
wrench. Tighten rmly but do not overtighten.
NOTE: Tighten the machine screws evenly so the gap between the
base of the mount and the lower clamp brackets is the same on both
sides as well as the front vs. the back (Fig.6A). The gap should be
the same size to ensure it is properly mounted.
A
facing
out
(toward
water)
facing
in
(toward
boat)

7
CCD-0004215 Rev: 02.18.21
Operation
1. Choose the proper inner diameter size of the rubber compression
insert that ts the outer diameter of the agpole: ¾”, 1” or 1 ¼”.
NOTE: The sizes are included on the bottom of the rubber inserts.
2. Place the compression insert inside the coupler so the four slots
on the rubber compression insert are aligned with the four slots in the
agpole coupler (Fig.7).
NOTE: Make sure to push the insert flush with the bottom of the
coupler.
3. Slide the agpole through the hand knob (Fig.7A).
4. Place the agpole into the insert and coupler and thread the knob
onto the coupler (Fig.8).
5. Tighten rmly by hand but do not overtighten.
6. Pull the agpole upward with slight pressure to ensure it is properly
fastened inside the coupler. The agpole should not move upward.
square
rain drain
aligned
with
round
rain drain
Fig.7 Fig.8
A

The contents of this manual are proprietary and copyright protected by Lippert Components,
Inc. Lippert™ prohibits the copying or dissemination of portions of this manual unless
prior written consent from an authorized Lippert representative has been provided. Any
unauthorized use shall void any applicable warranty. The information contained in this manual
is subject to change without notice and at the sole discretion of Lippert. Revised editions are
available for free download from taylormadeproducts.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact:
Taylor Made
Ph: 800-628-5188|Web: taylormadeproducts.com
Email: https://www.taylormadeproducts.com/support/contact-us/