Taymor ASTRAL 06-4022 User manual

INSTALLATION INSTRUCTIONS
ASTRAL 06-4022
ROMAN TUB FAUCET
TURN OFF
TURN OFF
SILICONE
Your installation may require
new supply lines.
(Supply lines are not included.)
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench Silicone caulk
2TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves.
These are usually found near water meter.
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
3DECK PREPARATION
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to 1-11/16” thick.
4INSTALL THE VALVE SYSTEM
From underneath the deck, insert valve body with rubber washer (1), metal washer (2) and
mounting nut (3) through holes on the right (cold) side. From above, thread flange (4) onto
valve stem. Tighten mounting nut (3), so that the flange (4) sits flush to the surface of working
area. Then insert the other valve body through holes on the left (hot) side and install in the
same way. NOTE: HOT side end valve is labeled.
Screw the handle seat (1) onto the flange (2). Place the handle (3) onto the
inverter (4) and secure with screw (5). Insert the index (6).
6
7
8
Place the spout assembly (1) through mounting hole in deck. Secure the spout assembly
(1) with rubber washer (2), metal washer (3) and nut (4).
Mount the spray support assembly. Place the spray support assembly (1) through
mounting hole in deck. Secure the spray support assembly (1) with washer (2) and nut
(3). Tighten nut securely with wrench.
Screw the connector (1) onto tube (2). Inset the hand held shower (3) into the spray
support assembly (4). Screw the shower hose coupling (5) onto the connector.
5" min.(127mm)
4~6"(102-152mm)
8~16"(203-406mm)
3" min.
(76mm)
Ø1-1/8"
(29mm)
1-11/16" (43mm) MAX. DECKTHICKNESS
Ø1-3/8"
(35mm)
Ø1-9/16"
(40mm)
Ø1-3/8"
(35mm)
4
3
12
1
2
3
4
1
2
3
1
2
3
4
5
1
3
5
6
2
4
5

INSTALLATION INSTRUCTIONS
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
12 EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners,
steel wool and harsh chemicals as these will dull the finish and void your warranty.
CAUTION: Check all connections for leaks.
Failure to do so can result in water damage.
11 FLUSHING
IMPORTANT: After installation is completed, turn on the hot and cold water sup-
plies. Check for leaks. Flush the water lines for one minute. Press the pin (1) to the
bottom position, and flush water lines for one minute. This flushes away any debris
that could cause damage to internal parts. Check for leaks. After flushing, turn the
handles all the way to off to shut off the water. The pin should now be in its normal
postion. Re-tighten any connections if necessary, but do not overtighten.
ASTRAL 06-4022
ROMAN TUB FAUCET
9Connect the flexible water supply hose (1) to the bottom of valve bodies (2) as shown.
Carefully bend the hoses to fit available space.
10 Connect water supply lines (1) to faucet inlets (2).
(supply lines not included)
22
1
1
1
1 - SPOUT
2 - AERATOR 3 - INDEX
4 - SCREW
5 - O-RING
6 - HANDLE
7 - HANDLE SEAT
8 - HANDLE FLANGE
9 - WASHER
10 - INVERTER
11 - BONNET
12 - CARTRIDGE (H&C)
13 - WASHER
14 - WASHER
15 - MOUNTING NUT
16 - BODY
17 - HOSE
18 - SET SCREW
19 - VALVE
20 - SPOUT SEAT
21 - WASHER
22 - O-RING
24 - HOSE
25 - O-RING
26 - WASHER
27 - WASHER
28 - MOUNTING NUT
29 - CONNECTOR
30 - HANDLE SHOWER
31 - SHOWER SEAT
32 - HOSE
1
2
23 - INDEX