Taymor CALEDONIA 06-4091HS User manual

INSTALLATION INSTRUCTIONS
CALEDONIA 06-4091HS / 06-4091HSSN
ROMAN TUB FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
ASME A112.18.1/CSA B125.1 and NSF-61
TURN OFF
TURN OFF
SILICONE
Your installation may require new supply
lines. (Supply lines are not included.)
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench Silicone caulk
2TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves.
These are usually found near water meter.
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
3DECK PREPARATION
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to 1-1/4” thick.
4INSTALL THE VALVE SYSTEM
Place a flange on each housing assembly.
Thread each flange down. Adjust each lower
locknut and washer. Wrench tighten locknuts.
Place a handle flange on each housing
assembly. Thread each handle flange down.
5HANDLE INSTALLATION
Install handles (1) and tighten the set screw (2).
Remove lift rod knob (1) and remove set
screw (2).
Remove spout (1) from diverter body (2).
Remove connector (1) from diverter body (2). From underneath the deck, insert diverter
body with rubber washer (1), metal washer
(2) and mounting nut (3) through center hole.
From above, thread connector (4) onto di-
verter body. Tighten mounting nut (3), so that
the connector (4) sits flush to the surface of
working area.
TORQUE
11 - 15 FT/LBS.
7SPOUT INSTALLATION
Assemble and align spout (1) onto diverter body and tighten set screw (2). Insert index
(5). Place lift rod knob (3) onto lift rod (4) and hand tighten.
Remove flange (1) from housing assembly. With the housing assembly marked “HOT” on
the left, insert the housing assembly through
the mounting holes from the underside of the
deck/rim.
A B
C D
6DIVERTER INSTALLATION
A B
C D
1
1
TORQUE
11 - 15 FT/LBS.
TORQUE
11 - 15 FT/LBS.
1
2
1
2
2
1
1
2
4
2
1
3
4
1
3
2
5
4~6"(10.2-15.2cm)
5" min.(12.7cm)
3" min.
(7.6cm)
8~16"(20.3-40.6cm)
Ø1-3/8”
(35mm)
Ø1-1/8”
(29mm)
Ø1-3/8”
(35mm)
Ø1-3/8”
(35mm)
1-1/8” (29mm) MAX. DECK THICKNESS

INSTALLATION INSTRUCTIONS
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
13 EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners,
steel wool and harsh chemicals as these will dull the finish and void your warranty.
8HOSE GUIDE INSTALLATION
Insert hose guide (1) into deck. From underneath deck, secure hose guide
with rubber washer (1), metal washer (2)
and locknut (3). Wrench tighten.
Connect the valve body outlets to the
diverter body inlets using high flow flexible
lines supplied.
A B
C
9SPRAY HOSE CONNECTION
Insert coiled spray hose (1) through hose
guide (2).
Carefully thread and tighten one end of the
braided connector hose (1) to the coiled
spray hose (2) and one end to the diverter
body (3). Restrain coiled spray hose (2) with
clip (4).
1
3
2
4
A B
CAUTION: Check all connections for leaks.
Failure to do so can result in water damage.
WATER SUPPLY CONNECTION
Connect water supply lines (1) to housing assembly (2). Hot water supply lines go into
left inlet. Cold water supply lines go into right inlet. (Supply lines not included.)
11 FLUSHING
Turn on hot and cold water supplies and flush the
water lines for one minute. Pull hose to its farthest
extension and point it down into the tub. Pull the lift
rod up to the full ON position and flush water lines
for one minute. After flushing, turn the handles all
the way off to shut off the water. The lift rod should
now be in its normal position.
12 HAND HELD SHOWER INSTALLATION
Connect hand held shower (1) into the end of the elbow (2)
by turning clockwise. Hand tighten.
10
CALEDONIA 06-4091HS / 06-4091HSSN
ROMAN TUB FAUCET
1 - LIFT ROD KNOB
2 - LIFT ROD
3 - INDEX
4 - SPOUT
5 - SET SCREW
6 - RECTIFIER 7 - DISC
8 - O-RING
9 - VALVE
11 - HANDLE
12 - SET SCREW
14 - CONNECTOR
15 - INVERTER
16 - HANDLE FLANGE
17 - DIVERTER
18 - O-RING
19 - CONNECTOR
20 - O-RING
21 - WASHER
22 - RUBBER
WASHER
23 - METAL
WASHER
24 - LOCKNUT
25 - BODY
26 - BONNET
27 - CARTRIDGE ASSEMBLY
28 - FLANGE
29 - FLANGE
WASHER
30 - RUBBER WASHER
31 - METAL WASHER
32 - LOCKNUT
33 -HOUSING
ASSEMBLY
34 - COUPLING NUT
35 - HIGH FLOW FLEXIBLE LINES
36 - BRAIDED CONNECTOR HOSE
37 - HAND HELD SHOWER
38 - SHOWER FLANGE
39 - SET SCREW
41 - ELBOW
42 - LONG SHANK
43 - WASHER
44 - RUBBER
WASHER
45 - METAL
WASHER
47 - CLIP
48 - COILED
SPRAY
HOSE
TORQUE
6 - 10 FT/LBS.
1
2
1
2
1
TORQUE
11 - 15 FT/LBS.
1
2
3
1
2
1
2
10 - HANDLE SEAT
13 - O-RING
40 - O-RING
46 - NUT