Taymor MANDALAY 06-4006HS User manual

INSTALLATION INSTRUCTIONS
MANDALAY 06-4006HS
ROMAN TUB FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
ASME A112.18.1/CSA B125.1 and NSF-61
TURN OFF
TURN OFF
SILICONE
Your installation may require new supply
lines. (Supply lines are not included.)
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
1
2
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench Silicone caulk
2TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves.
These are usually found near water meter.
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
3DECK PREPARATION
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to 1-1/4” thick.
4INSTALL THE VALVE SYSTEM
Place a flange on each housing assembly.
Thread each flange down. Adjust each lower
locknut and washer. Wrench tighten locknuts.
5HANDLE INSTALLATION
Install handles (1), secure with screw (2), insert cap (3) and tighten the set screw (4).
Remove lift rod knob (1) and remove set
screw (2).
Remove spout (1) from diverter body (2).
Remove connector (1) from diverter body (2). From underneath the deck, insert diverter
body with rubber washer (1), metal washer
(2) and mounting nut (3) through center hole.
From above, thread connector (4) onto di-
verter body. Tighten mounting nut (3), so that
the connector (4) sits flush to the surface of
working area.
TORQUE
11 - 15 FT/LBS.
7SPOUT INSTALLATION
Assemble and align spout (1) onto diverter body and tighten set screw (2). Insert index
(5). Place lift rod knob (3) onto lift rod (4) and hand tighten.
Remove flange (1) from housing assembly. With the housing assembly marked “HOT” on
the left, insert the housing assembly through
the mounting holes from the underside of the
deck/rim.
A B
C
6DIVERTER INSTALLATION
A B
C D
1
1
TORQUE
11 - 15 FT/LBS.
TORQUE
11 - 15 FT/LBS.
2
1
3
2
1
4
1
2
4
2
1
3
2
1
3
4
5
4~6"(10.2-15.2cm)
5" min.(12.7cm)
3" min.
(7.6cm)
8~16"(20.3-40.6cm)
Ø1-3/8”
(35mm)
Ø1-1/8”
(29mm)
Ø1-3/8”
(35mm)
Ø1-3/8”
(35mm)
1-1/8” (29mm) MAX. DECK THICKNESS

INSTALLATION INSTRUCTIONS
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
13 EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners,
steel wool and harsh chemicals as these will dull the finish and void your warranty.
8HOSE GUIDE INSTALLATION
Insert hose guide (1) into deck. From underneath deck, secure hose guide
with rubber washer (1), metal washer (2)
and locknut (3). Wrench tighten.
Connect the valve body outlets to the
diverter body inlets using high flow flexible
lines supplied.
A B
C
9SPRAY HOSE CONNECTION
Insert coiled spray hose (1) through hose
guide (2).
Carefully thread and tighten one end of the
braided connector hose (1) to the coiled
spray hose (2) and one end to the diverter
body (3). Restrain coiled spray hose (2) with
clip (4).
1
2
3
4
A B
CAUTION: Check all connections for leaks.
Failure to do so can result in water damage.
WATER SUPPLY CONNECTION
Connect water supply lines (1) to housing assembly (2). Hot water supply lines go into
left inlet. Cold water supply lines go into right inlet. (Supply lines not included.)
11 FLUSHING
Turn on hot and cold water supplies and flush the
water lines for one minute. Pull hose to its farthest
extension and point it down into the tub. Pull the lift
rod up to the full ON position and flush water lines
for one minute. After flushing, turn the handles all
the way off to shut off the water. The lift rod should
now be in its normal position.
12 HAND HELD SHOWER INSTALLATION
Connect hand held shower (1) into the end of the coiled
spray hose (2) by turning clockwise. Hand tighten.
10
1 - LIFT ROD KNOB
2 - LIFT ROD
3 - INDEX
4 - SPOUT
5 - SET
SCREW
6 - RECTIFIER
TORQUE
6 - 10 FT/LBS.
1
2
1
2
21 - DIVERTER
22 - O-RING
23 - CONNECTOR
24 - O-RING
25 - WASHER
26 - RUBBER
WASHER
27 - METAL
WASHER
28 - LOCKNUT
29 - BODY
1
TORQUE
11 - 15 FT/LBS.
1
2
3
1
2
15 - DISC
16 - O-RING
17 - VALVE
7 - SPOUT FLANGE
8 - SCREW
9 - CAP
10 - HANDLE
11 - SCREW
12 - WASHER
13 - SET SCREW
14 - HANDLE SEAT
18 - SET SCREW
19 - SHOWER FLANGE
30 - BONNET
31 - CARTRIDGE
ASSEMBLY
32 - FLANGE
33 - FLANGE
WASHER
34 - RUBBER WASHER
35 - METAL WASHER
36 - LOCKNUT
37 - HOUSING
ASSEMBLY
38 - COUPLING NUT
39 - HIGH FLOW FLEXIBLE LINES
40 - BRAIDED CONNECTOR HOSE
20 - HAND HELD SHOWER
41 - LONG SHANK
42 - WASHER
43 - RUBBER
WASHER
44 - METAL
WASHER
46 - CLIP
47 - COILED
SPRAY
HOSE
45 - NUT
2
1
MANDALAY 06-4006HS
ROMAN TUB FAUCET