Taymor DIXON 06-4037HS User manual

INSTALLATION INSTRUCTIONS
DIXON 06-4037HS
ROMAN TUB FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
ASME A112.18.1/CSA B125.1 and NSF-61
TURN OFF
TURN OFF
SILICONE
Your installation may require
new supply lines.
(Supply lines are not included.)
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench Silicone caulk
2TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves.
These are usually found near water meter.
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
3DECK PREPARATION
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to 1-1/8” thick.
4INSTALL THE VALVE SYSTEM
Place a flange (1) on each housing assembly.
Thread each flange down until it locks onto
housing assembly.
5HANDLE INSTALLATION
Ensure the o-ring (1) is placed in the handle seat (2) before installing. Then place handle
assembly (3) onto the right (cold) valve stem (4). Then thread the handle seat (2) onto the
flange (5). Place the other handle assembly onto the left (hot) valve stem and install the
same way. After install handle assembly, if the handle seat is not aligned with handle in
a line as shown in the above diagram (6), rotate the handle seat back (the rotating
angle can not exceed 90° ) to make the handle seat align with handle in a line.
7HOSE GUIDE INSTALLATION
Remove flange (1) from housing assembly. With the housing assembly marked “HOT” on
the left, adjust washers (1) and lock nut (2) to
the bottom of the housing assembly. Insert
the housing assembly through the mounting
holes from the underside of the deck/rim.
A B
C
6SPOUT INSTALLATION
1
1
1
2
From underneath the deck secure housing
assembly with lock nut (3) and washers (2).
Wrench tighten locknut (3).
D
1
TORQUE
11 - 15 FT/LBS.
TORQUE
11 - 15 FT/LBS. 3
2
Insert hose guide (1) into deck hole. From underneath deck, secure hose guide
with rubber washer (1), metal washer (2)
and locknut (3). Tighten locknut (3) securely
with wrench. NOTE: Suggest the torque on
locknut (3) is in the range of 11-15 ft/lbs.
Connect the flexible water supply hose (1) to the bottom of valve bodies (2) as show. Align middle
body (3) in a position which will allow maximum clearance to connect hoses. Carefully bend the
hoses to fit available space. Carefully thread the hose couplings to the sides of the middle body (3).
NOTE: Suggest the connective torque between (1) and (2), (1) and (3) is in the range of 6-10 ft/lbs.
A B
C
4~6"(10.2-15.2cm)
5" min.(12.7cm)
3" min.
(7.6cm)
8~16"(20.3-40.6cm)
Ø1-3/8”
(35mm)
Ø1-1/8”
(29mm)
Ø1-3/8”
(35mm)
Ø1-3/8”
(35mm)
1-1/8” (29mm) MAX. DECK THICKNESS
4
3
2
1
6
5
Remove collar (1) from diverter body.
From above, place collar (1) on diverter body.
Thread collar down until it locks onto diverter body
fully. From underneath the deck, secure diverter
body with locknut (3) and washers (2). Wrench
tighten locknut (3). NOTE: Suggest the torque on
locknut (3) is in the range of 11-15 ft/lbs.
A
C
1
Adjust washers (1) and locknut (2) to the
bottom of diverter valve, insert the diverter
through the mounting hole from the
underside of the deck/rim.
B
2
1
Assemble and align spout (1) onto diverter
body and tighten set screw with allen wrench
(2). Place button (3). Thread lift rod (4) onto
diverter body through the spout (1) tightly.
D
3
2
1
4
1
3
2
1
3
2
1
32
2
1
1

INSTALLATION INSTRUCTIONS
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
13 EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners,
steel wool and harsh chemicals as these will dull the finish and void your warranty.
8SPRAY HOSE CONNECTION
Insert coiled spray hose (1) onto hose guide
(2). Restrain coiled spray hose (1) with clip (3).
Connect the flexible water supply hose (1) to the
coiled spray hose (2) and the middle body (3).
Carefully bend the hoses to fit available space.
Carefully thread the hose couplings to the
coiled spray hose (2) and the side of the middle
body (3). NOTE: Suggest the connective torque
between (1) and (2), (1) and (3) is in the
range of 6-10 ft/lbs.
A B
CAUTION: Check all connections for leaks.
Failure to do so can result in water damage.
WATER SUPPLY CONNECTION
Connect water supply lines (1) to faucet inlets (2). Hot water supply lines go into left inlet.
Cold water supply lines go into right inlet. (Supply lines are not included.)
NOTE: Suggest the connective torque between (1) and (2) is in the range of 6-10 ft/lbs.
10 FLUSHING
Turn on hot and cold water supplies and flush water lines for one minute. Remove
the clip (1), pull hose to its farthest extension and point it down into the tub. Pull the
lift rod up to the full ON position and flush water lines for one minute. After flushing,
turn the handles all the way off to shut off the water. The lift rod should now be in its
normal position.
9
CAUTION: Check all connections for leaks.
Failure to do so can result in water damage.
12 HAND HELD SHOWER INSTALLATION
Connect hand held shower (1) into the end of the coiled spray hose (2) by turning
clockwise. Hand tighten.
DIXON 06-4037HS
ROMAN TUB FAUCET
2
1
3
3
2
1
2
1
1
2
1
2
1
1 - LIFT ROD KNOB
2 - LIFT ROD
3 - O-RING
4 - SCREW
5 - INDEX 6 - HANDLE
7 - CLIP
8 - HANDLE SEAT
9 - O-RING
10 - HANDSHOWER
11 - SCREW
12 - FLANGE
13 - O-RING
14 - TUBE
15 - WASHER
16 - WASHER
17 - WASHER
18 - NUT
19 - CLIP
20 - WASHER
21 - VALVE
22 - O-RING
23 - BONNET
24 - CARTRIDGE
25 - FLANGE SEAT
26 - WASHER
27 - WASHER
28 - WASHER
29 - MOUNTING NUT
30 - BODY
31 - COUPLING NUT
32 - HOSE
33 - HOSE
34 - T-TUBE
35 - NUT
36 - WASHER
37 - WASHER
38 - WASHER
39 - O-RING
40 - CONNECTOR
41 - O-RING
42 - SWITCH
43 - CAP
44 - RECTIFIER
45 - SPOUT