TBK vision PTZ6327 User manual

Outdoor High Speed Dome SystemOutdoor High Speed Dome System
User ManualUser Manual

Contents
Before installing
Key features
Configure, fix and wire
Basic speed dome operation
Programming the speed dome
Using the speed dome features
Parts and dimensions
Wiring schematic
Specifications
1
2
3
7
9
13
14
15
17
Outdoor High Speed Dome System
Appendix Of Outdoor High Speed Dome System

Before installing
1
!
·Installation should be carried out only by qualified personnel and in accordance with
any wiring regulations in force at the time.
·The speed dome is heavy and could cause injury if not correctly mounted in
accordance with these instructions. Use only the fittings supplied with the speed
dome and ensure that all lanyard safety cables are connected correctly during
installation.
·Adequate protection against lightning strikes and power surges must be installed to
prevent damage to the speed dome.
·Any safety warnings on the product and in these instructions must be adhered to.
·If cleaning is necessary, disconnect power to the speed dome first. Do not use
abrasive cleaners, as these will cause damage to the cover and cause poor image
quality. Use a damp cloth to gently clean the dome cover and dry off with a soft
clean cloth.
·Do not use any brackets, mounts or other accessories not specifically designed for
use with this speed dome.
Do not attempt to service or repair the speed dome as opening or removing covers
may expose dangerous voltages or other hazards. Refer all servicing to qualified
service personnel.

Key features
2
Presets
Up to 127 sets of positional and zoom level information can be stored as
presets. These can be called manually by the operator, automatically by an
alarm input, or grouped to form a sequence of actions to run automatically.
Each preset can also be programmed with the following:
Alarm action - relay outputs can be triggered when particular presets are
called
Title - each preset can be titled with up to 10 characters so that zones can
easily be identified
Pattern tours
Any dome movement can be recorded - and subsequently played back - as
four separate pattern tours. These can be played back individually or
grouped to form a sequence of tours.
Swing between 2 presets
swing is a useful feature when, for example, the operator wishes to ‘patrol’
a perimeter fence. If one preset is defined at one end of the fence and a
second preset is defined at the other, the swing function will smoothly and
accurately move from one end to the other and then back again in a
repeating sequence. Speed can be adjusted as necessary and up to 8
swing functions can be defined.
Group function
The group function is a powerful feature which allows the operator to define
a sequence of speed dome actions to form an automatic patrol sequence.
Actions can be a mix of preset positions, pattern tours and swing functions.
Up to 8 groups can be defined and each group can have up to 20 actions
which repeat indefinitely until interrupted by the operator or an alarm input.
Specific parameters such as preset speed, dwell time and action loop can
also be specified
Privacy zones
By defining a privacy zone, sensitive scenes such as windows can be
masked off so they cannot be viewed by the operator. Up to 8 privacy
zones can be defined. Privacy zone size adjusts automatically depending
on the speed dome zoom level.
Alarm inputs and outputs
This speed dome has 8 alarm inputs and 4 alarm outputs. Any alarm input
can be set to call a predefined preset, swing function, pattern or group. Any
preset can be configured to activate any or all of the alarm outputs. For
example, a PIR detector connected to alarm input 1 could call preset 7 to
view that particular scene whilst activating an external lamp connected to
relay 1 and an external siren connected to relay 3.
On Screen Display (OSD)
The operator can choose if any or all of the following information is
displayed on screen during normal speed dome operation.
Preset status and title
Speed dome position coordinates and zoom level
Alarm I/O status
·Time and Date
Speed dome ID
The speed dome also has a full on screen menu setup allowing quick and
easy configuration of all the speed dome features.
Powerful park function
The speed dome can be configured to run a specified swing function,
pattern tour, group or preset after a defined period of inactivity.

Configure, fix and wire
3
1. Remove the foam packing pieces
3. Reassemble the speed dome
Protocol & Baud rate DIP switch table
Speed dome ID DIP switch table
2. Change protocol, baud rate and ID if required
Before proceeding with installation, the speed dome foam packing
pieces must be removed. Remove the outer dome cover with the tool
supplied and carefully remove the foam packing pieces. When
handling the dome cover, always wear the gloves supplied to avoid
getting fingerprints on the outer dome cover.
Refit the black inner dome cover and outer dome cover. If the
lanyard safety wire was removed, it must be refitted before the dome
cover is fixed.
The factory default setting is Pelco D, 2400, ID 1. Skip to section
3 if these settings match your control equipment
Foam
Foam
Cover
Lanyard
1. Wearing the gloves and using the supplied
tool, remove the outer dome cover.
1. Carefully unclip the black inner dome 2. Locate the dip switches and set protocol
and ID according to the table opposite.
2. Remove the foam pieces from the camera
module.
Foam
1 2 3 4 5 6 7 8
1 2 3 4 5 6
ON
ON
ID
Protocol
1 2 3 4 5 6
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
---
OFF
ON
ON
OFF
ON
ON
OFF
ON
OFF
---
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
---
1
2
3
5
7
255
4
6
8
-
OFF
ON OFF
OFF ON
ON
ON
Pelco D, 2400 bps
Pelco D, 9600 bps
Pelco P, 4800 bps
Pelco P, 9600 bps
P r o t o c o l / R a t e
1
1
12345678 D I P
2 4 8 1 6 3 2 6 4 1 2 8 Va l I D
2
Note: Dip switches 3 - 6 are reserved and must not be changed.
Note: ID 0 should not be used. Where multiple speed domes
are connected, a unique ID must be assigned to each one.
1 2 3 4 5 6 7 8
ON
Factory default
switch positions
Speed dome ID is set
using standard
binary notation
Outdoor High Speed Dome System 1 2 3 4 5 6
ON
Factory default switch positions
PAL NTSC

4. Fix the bracket 5. Wire up the junction box
1. Fix the supplied mounting template, taking
account of any pipework, cables, overhangs
etc. that may obstruct the bracket once fitted.
3. Remove the junction box cover. Using the
supplied bolts and tool, firmly fix the bracket.
Pendent option
Pendent option
6. Tighten the three screws to fix the speed
dome and ensure the lanyard safety chain is
properly connected.
4. Feed the speed dome cable through the
bracket.
2. After making suitable checks for buried
pipes and cables, drill fixing holes suitable for
the bolts supplied with the speed dome.
Lanyard
B A
O1 O2 O3 O4
A2A1 A3A4 G
B A ~ ~
A6
A5 A7A8
RS-485 Termination Resistor
Video output
Speed dome cable
RS-485
24V AC Power
Alarm Input 1-8 Alarm Output 1-4
G
1234
Alarm Input 1-4
5 6 7 8
Alarm Input 5-8
Alarm Output 4
Alarm Output 3
ON
1
Alarm Output 2
Alarm Output 1
Junction box PCB detail
4
NO NCNO NC
Alarm 3 Output State
Alarm 4 Output State
NC or NO
NC or NO
Pendent option
5. Bring the speed dome up to the bracket.

6. Complete the install
1a - wall bracket option. After making all the
connections to the PCB, fit the junction box
cover with the four screws.
Note: when fixing the cover to the junction box, ensure that the seal is also
fitted properly and that none of the cables are trapped
1b - pendent option. After making all the
connections to the PCB, raise the dome
assembly to the junction box, connect the
dome cable to the PCB and fix with the four
screws.
Seal
Seal
Verify basic operation
1. After carefully checking the installation,
including all cable connections, apply power to
the dome and check that the startup and self
test screen is displayed.
2. After the self test is complete, the dome
starts normal operation. Verify that there is
basic PTZ control from your control equipment.
H IG H S P E E D DO M E
- -- - - - - -- - - - - -- - - - -- - - - -
F IR M W A R E VE R
C OL O U R S Y ST E M
P RO T O C O L
A DD R E S S
B AU D R A T E
D AT A M E M O RY
Z OO M M O D U LE
A LA R M I / O
H OM E T E A C HI N G . .
O : - - - -
I : 1 2 3 4 5 6 7 8
3 2 5 / 3 7 / x 1
: 0 .3 S 1 8 V
: P AL
: P EL C O - D
: 1
: 2 40 0
: O K
: O K
: O K
E ND
W AI T . . .
0 7 / J A N / 2 0 0 7
1 4 : 4 6 : 4 6
C AM 1
…work through the logical steps below to determine and rectify the problem
No picture - check the PCB to make sure the red power LED is lit. If not, check that the PSU is
correctly connected and has power. If you have a test meter, verify that the output of the PSU is
approximately 24V AC.
If the power LED is lit, check the BNC crimp connection is correctly made at both the PCB end and
the DVR / monitor / matrix end. A portable test monitor connected directly to the video output of the
speed dome is also a useful test - if a picture is displayed, double check the BNC connections and
the signal cable used.
No PTZ control - check that the control equipment you are using is compatible with the speed
dome and is configured to match the speed dome settings correctly.
If dip switches were changed on the speed dome, check the power on self test screen to ensure
that protocol, ID and baud rate are as expected.
If the settings match, you should check the polarity of the connections, both on the control
equipment and the speed dome. If you suspect there is a polarity issue, swap the A & B wires at the
speed dome to see if this resolves the problem.
Check also that there are no other telemetry devices on the system with the same ID as the speed
dome. If in doubt, connect the speed dome directly to the PTZ controller and isolate all other
equipment.
5

6
0 7 / J A N / 2 0 0 7
0 9 : 3 7 : 1 5
C A M 1
O : - 2 3 -
I:12345678
307/46/x3
P R E S E T 3
P R E S E T 3
P AR K I N G B AY 1
R E C E P T I O N
Basic speed dome operation
Programming, calling and deleting presets
Understanding the On Screen Display (OSD)
S ET P R E S E T1
There are many different PTZ keyboards and DVR systems capable
of controlling this speed dome, and it would be impossible to
describe them all here. Therefore, examples given in the following
pages are based on the more popular control equipment available.
Whilst the principles of operation are the same, regardless of the
control equipment used, reference may need to be made to the
manual supplied with your particular control equipment.
To program a preset position, move the speed
dome to the desired scene and zoom level
and press:
SET - XXX - ENTER
Where XXX is a preset number between 1 &
128 (but note that preset 95 is reserved and
cannot be used). Confirmation is displayed on
the OSD.
To delete a preset position, press:
CLEAR - XXX - ENTER
Where XXX is a preset number between 1 &
128 (but note that preset 95 is reserved and
cannot be used). The preset position is
cleared from memory.
To reprogramme a preset position, follow the
steps for programming a preset - it is not
necessary to delete the old preset position first
PRESET LABEL: If defined,
is displayed when a preset
position is called
CAMERA ID: Shows the
current ID as defined by the
dip switch settings
ALARM I/O: Shows which
alarm inputs and outputs are
active
DATE/CLOCK: Shows
current time and date
PTZ INFORMATION: The current
pan/tilt position in degrees and
the current zoom level
ACTION TITLE: Shows
current speed dome
action
To go to a preset position thats already
been programmed, press:
SHOT - XXX - ENTER
Where XXX is a preset number between 1 &
128 (but note that preset 95 is reserved and
cannot be used). The speed dome moves to
the preset position. Confirmation and preset
title (if defined) is displayed on the OSD.
O : - - - -
I : 1 2 3 4 5 6 7 8
3 2 5 / 3 7 / x 1
O : - - - -
I : 1 2 3 4 5 6 7 8
3 2 5 / 3 7 / x 3
07/JAN/2007
1 2 : 3 8 : 0 5
C AM 1
0 7 / J A N / 2 0 0 7
1 2 : 4 2 : 2 2
C AM 1

Display setup Set date/clock
System information
The speed dome setup menu allows the operator to customise and
program all aspects of speed dome operation. All menu settings are
retained in non-volatile memory so if power is lost to the speed dome
for any reason, all settings will be retained.
H I G H S PE ED D OM E
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
< S Y S TE M IN FO R M A T I O N >
< D I S PL AY S ET U P >
< D O M E CA ME RA S E T U P >
< P A S SW OR D SE T U P >
< S Y S TE M IN IT I A L I S E >
E X I T
D I S P LA Y SE TU P
-----------------------------
C A M E RA I D
P T Z I N FO RM AT I O N
A C T I ON T IT LE
P R E S ET L AB EL
A L A R M I/ O
D A T E /C LO CK
< S E T D AT E/ CL O C K >
< P R I VA CY Z ON E >
B A C K
E X I T
S E T D A TE /C LO C K
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
D A T E 0 7/ JA N/ 2 0 0 7
C L O C K 14 :3 7: 1 5
B A C K
E X I T
S Y S T EM I NF OR M A T I O N
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
F I R M WA RE V ER
C O L O UR S YS TE M
P R O T OC OL
A D D R ES S
B A U D R AT E
B A C K
E X I T
To access the speed dome setup menu, key:
SHOT - 95 - ENTER
To navigate the main menu, move the joystick
up / down to choose a menu item or change
settings within a menu item.
To enter a menu item or confirm a new setting,
key: NEAR
To exit a menu item or cancel a new setting,
key: FAR
Where a menu item is surrounded by
brackets, it indicates that there is a sub menu.
Where a menu screen shows EXIT, selecting
this option will exit the menu and the speed
dome will return to normal operation. Where a
menu screen shows BACK, selecting this
option will return to the higher menu level.
The main menu has five options:
<SYSTEM INFORMATION> - Provides
information such as firmware version, protocol
and ID values as defined by the dip switch
settings.
<DISPLAY SETUP> - Allows the operator to
specify which On Screen Display information
is shown during normal operation. Also allows
privacy zones to be defined and time/date to
be changed
<DOME CAMERA SETUP> - Allows all
operating features of the speed dome to be
programmed and managed. Also allows
settings for the camera module to be changed
<PASSWORD SETUP> - Allows a password
to be set to protect the speed dome setup
<SYSTEM INITIALISE> - Allows various
speed dome settings to be reset to factory
defaults
From the main menu, use the joystick to
highlight SYSTEM INFORMATION and key:
NEAR
To return to the main menu, highlight BACK
and key: NEAR
To exit the setup menu completely, highlight
EXIT and key: NEAR
From the main menu, use the joystick to
highlight DISPLAY SETUP and key: NEAR
CAMERA ID (ON / OFF) - shows camera ID
according to the DIP switch settings, eg
CAM 1.
PTZ INFORMATION (ON / OFF / AUTO) -
shows the current pan / tilt position in degrees
and the current zoom level.
ACTION TITLE (ON / OFF / AUTO) - shows
current speed dome action, eg PRESET3.
PRESET LABEL (ON / OFF / AUTO) - shows
preset title (if defined) when a preset is called.
ALARM I/O (ON/OFF) - shows real time
status of the alarm inputs and outputs.
<SET DATE/CLOCK) - sub menu to change
the date and time
<PRIVACY ZONE> - sub menu to setup the
speed dome privacy zones
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
Note: If the auto option is chosen, the relevant
information is displayed for a few seconds
before disappearing.
From the display setup menu, use the joystick
to highlight SET DATE/CLOCK and key:
NEAR
Highlight the item to modify and key: NEAR
Move the joystick up and down to change an
individual value and left and right to move to
the previous / next value
Key: NEAR to save or: FAR to cancel.
: 0 . 3 S 18 B
: P A L
: P E L C O- D
: 1
: 2 4 0 0
O N
A U T O
A U T O
A U T O
A U T O
O N
7
Programming the speed dome

Z O O M C AM ER A SE T U P
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
F O C U S MO DE
D I G I TA L ZO OM
F L I C KE RL ES S
C O L O UR
< W H I TE B AL AN C E S E T U P >
< A U T O EX PO SU R E S E T U P >
B A C K
E X I T
D O M E C AM ER A SE T U P
-----------------------------
< C A M ER A SE TU P >
< M O T IO N SE TU P >
< P R E SE T SE TU P >
< S W I NG S ET UP >
< P A T TE RN S ET U P >
< G R O UP S ET UP >
B A C K
E X I T
From the main menu, use the joystick to
highlight DOME CAMERA SETUP and key:
NEAR
<CAMERA SETUP> - setup of specific
camera module features.
<MOTION SETUP> - setup of the pan / tilt /
zoom operation of the speed dome, park
action configuration, and configuration of the
alarm inputs.
<PRESET SETUP> - full management and
programming of individual presets.
<SWING SETUP> - full management and
programming of swing functions.
<PATTERN SETUP> - full management and
programming of pattern tours.
<GROUP SETUP> - full management and
programming of group functions.
Highlight the setup menu required and key:
NEAR
Remember: A menu item surrounded by
brackets shows it has a sub menu.
From the dome camera setup menu, use the
joystick to highlight CAMERA SETUP and key:
NEAR
FOCUS MODE
MANUAL - the operator must focus the
camera manually using the NEAR and FAR
keys
SEMIAUTO - the camera automatically
focuses during normal PTZ movement but
preset focus information is stored when a
preset is programmed and recalled each time
the preset is called
AUTO - the module auto focuses continually
DIGITAL ZOOM (ON / OFF) - disables or
enables the 12x digital zoom. When disabled,
the maximum zoom level is 18x (optical).
FLICKERLESS (ON / OFF) - should be set to
ON when used in certain lighting conditions
(EG Fluorescent lighting) to prevent picture
flicker
COLOUR (ON/OFF) - switches the module
between colour and b/w mode
<WHITE BALANCE SETUP> - sub menu to
change the white balance settings
<AUTO EXPOSURE SETUP> - sub menu to
change the auto exposure settings
Dome camera setup Camera setup
8
Privacy zone Edit zone
P R I V AC Y ZO NE
-----------------------------
Z O N E N O.
D I S P LA Y
C L E A R ZO NE
< E D I T ZO NE >
B A C K
E X I T
E D I T Z ON E 1
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
M O V E T O TA RG ET P O S I T I O N
[ N E A R : S E L E C T / F A R : C A N C E L ]
E D I T Z ON E 1
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
[ : A D J US T ZO NE W I D T H ]
[ : A D J US T ZO NE H E I G H T ]
[ N E A R: SA VE / F A R : C A N C E L]
From the display setup menu, use the joystick
to highlight PRIVACY ZONE and key: NEAR
ZONE NO. (1-8) - shows the privacy zone
currently being modified.
DISPLAY - determines whether the privacy
zone is displayed during normal operation.
<EDIT ZONE> - allows the operator to define
the privacy zone.
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
From the privacy zone menu, use the joystick
to highlight EDIT ZONE and key: NEAR
Use the joystick to move the speed dome to
the approximate position and zoom level for
the privacy zone and key: NEAR to select or
FAR to cancel and return to the privacy zone
menu.
1
O F F
C A N C E L
S E M I A U T O
O N
O F F
O N
Move the joystick left and right to finely adjust
the width of the privacy zone and up and down
to finely adjust the height.
To save the privacy zone, key: NEAR or key:
FAR to cancel.

White balance setup Auto exposure setup
W B S E T UP
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
W B M O D E
R E D A D JU ST
B L U E A DJ US T
B A C K
E X I T
A E S E T UP
-----------------------------
B A C K LI GH T
D A Y / NI GH T
A E M O D E
I R I S L EV EL
G A I N L EV EL
S H U T TE R SP D
B R I G HT NE SS
B A C K
E X I T
From the zoom camera setup menu, use the
joystick to highlight WHITE BALANCE SETUP
and key: NEAR
WB MODE (AUTO / MANUAL)
AUTO - the speed dome determines the
optimum white balance settings for a given
scene
MANUAL - the operator can adjust white
balance settings manually
RED ADJUST - in manual mode, the red
colour content can be adjusted
BLUE ADJUST - in manual mode, the blue
colour content can be adjusted
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
From the zoom camera setup menu, use the
joystick to highlight AUTO EXPOSURE
SETUP and key: NEAR
BACKLIGHT (ON/OFF) - switches backlight
compensation ON or OFF
DAY/NIGHT (AUTO/DAY/NIGHT) - the
operator can choose to fix the camera in to
DAY (colour) or NIGHT (B&W with IR cut filter
mode). In AUTO mode, the camera switches
between DAY and NIGHT depending on the
surrounding light level
AE MODE - in AUTO mode, the speed dome
determines optimum camera exposure
settings for a given scene. In modes other
than AUTO, the operator can adjust specific
exposure characteristics to suit a particular
scene
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
A U T O
- - -
- - -
O F F
A U T O
A U T O
- - -
- - -
- - -
- - -
M O T I ON S ET UP
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
P R E S ET L OC K
P W R U P A CT IO N
A U T O F LI P
J O G M A X SP EE D
J O G D I RE CT IO N
< P A R KI NG A CT I O N S E T U P >
< A L A RM A CT IO N S E T U P >
B A C K
E X I T
P A R K IN G AC TI O N S E T U P
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
P A R K E NA BL E
W A I T T IM E
P A R K A CT IO N
B A C K
E X I T
O F F
O N
O N
1 6 0 / S E C
I N V E R S E
O F F
0 0 : 1 0 : 0 0
H O M E
From the dome camera setup menu, use the
joystick to highlight MOTION SETUP and key:
NEAR
PRESET LOCK - when set to ON, preset
programming directly from the keyboard is
disabled to prevent tampering
PWR UP ACTION - when set to ON, the
speed dome will resume its last operation
when power is restored after a power failure
AUTO FLIP (ON / OFF) - when set to ON, the
dome will flip 180 degrees when the tilt
position reaches 90 degrees.
JOG MAX SPEED - determines the maximum
speed in degrees / second the dome will move
during manual operation
JOG DIRECTION (INVERSE / NORMAL) -
when set to normal, the pan direction is
opposite to the joystick movement.
<PARKING ACTION SETUP> - Configure
actions that run automatically after a defined
period of inactivity
<ALARM ACTION SETUP> - Configure the
action of the alarm inputs.
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
From the motion setup menu, use the joystick
to highlight PARKING ACTION SETUP and
key: NEAR
PARK ENABLE - when set to ON, the speed
dome will run the specified park action after
the wait time has elapsed
WAIT TIME - can be set between one minute
and 4 hours. If no manual control occurs
during this time, the park action will run
PARK ACTION - choose the action to run after
the wait time has elapsed. This can be return
to home position, go to a preset or run a
swing, GROUP or PATTERN TOUR
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
Motion setup Parking action setup
9

A L A R M AC TI ON S E T U P
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
A L A R M 1 AC T
A L A R M 2 AC T
A L A R M 3 AC T
A L A R M 4 AC T
A L A R M 5 AC T
A L A R M 6 AC T
A L A R M 7 AC T
A L A R M 8 AC T
B A C K
E X I T
P R E S ET S ET UP
-----------------------------
P R E S ET N O.
C L R P R ES ET
< E D I T SC EN E>
< E D I T LA BE L>
< R E L AY O UT >
B A C K
E X I T
E D I T S CE NE - P RE S E T 1
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
M O V E T O TA RG ET P O S I T I O N
[ N E A R: SA VE / F A R : C A N C E L]
From the motion setup menu, use the joystick
to highlight ALARM ACTION SETUP and key:
NEAR
ALARM 1....8 ACT - for each alarm action,
specifies the preset number, swing, pattern
tour or group to call. Leave set to NOT USED
to disable the alarm input.
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
N O T U S ED
N O T U S ED
N O T U S ED
N O T U S ED
N O T U S ED
N O T U S ED
N O T U S ED
N O T U S ED
1
C A N C E L
- - - -
From the dome camera setup menu, use the
joystick to highlight PRESET SETUP and key:
NEAR
PRESET NUMBER (1 - 128) - The preset
number currently being modified. If the preset
number is already defined, the speed dome
will move to that preset position, otherwise
UNDEFINED is displayed under the preset
number
CLR PRESET - use this option to delete the
current preset position
<EDIT SCENE> - use this option to program
the preset position
<EDIT LABEL> - use to edit the preset label.
This option is only available when the
selected preset position is already
programmed
<RELAY OUT> - use to program the relay
outputs required (if any) when the preset is
called. This option is only available when
the selected preset position is already
programmed
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
From the preset setup menu, use the joystick
to highlight EDIT SCENE and key: NEAR
Using the joystick, move the speed dome to
the desired position and zoom level and key:
NEAR to save or: FAR to cancel.
Alarm action setup Preset setup Edit scene Edit label
E D I T L AB EL - P RE S E T 1
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
[ ]
- - - - -- -- --
1 2 3 4 56 78 90 O K
A B C D EF GH IJ C A N C E L
K L M N OP QR ST
U V W X YZ ab cd
e f g h ij kl mn
o p q r st uv wx
y z < > -/ :.
Backspace
Space
From the preset setup menu, use the joystick
to highlight EDIT LABEL and key: NEAR
The solid white square shows the current
cursor position.
The flashing white square shows the currently
selected character.
Move the joystick up / down / left / right to
choose the required character and key: NEAR
to insert it in the preset label. The solid white
square moves to the next cursor position.
Repeat until the preset label is complete.
If a mistake is made, use the joystick to select
the backspace ( ) and key: NEAR. The cursor
moves back one square.
Select OK to save the preset label or
CANCEL to lose changes, and key: NEAR to
exit
10

From the preset setup menu, use the joystick
to highlight RELAY OUT and key: NEAR
RELAY OUT 1..4 (ON / OFF) - set which
relays are triggered when the preset is called.
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
Relay out
R E L A Y OU T - PR ES E T 1
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
R E L A Y OU T 1
R E L A Y OU T 2
R E L A Y OU T 3
R E L A Y OU T 4
B A C K
E X I T
O F F
O F F
O F F
O F F
From the dome camera setup menu, use the
joystick to highlight SCAN SETUP and key:
NEAR
SCAN NO. (1-8) - shows the SCAN number
currently being modified.
1ST POS. - any defined preset between 1 &
128.
2ND POS. - any defined preset between 1 &
128.
Scan SPEED - determines the speed of
movement in degrees per second between
each preset position.
CLEAR Scan - deletes the currently selected
Scan function.
RUN SCAN - runs the currently selected scan
function for testing purposes
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
Note: A Scan always moves anti-clockwise to
the 1st position and then clockwise to the 2nd
position.
Scan setup
S C A N S ET UP
-----------------------------
S C A N N O.
1 S T P O S.
2 N D P O S.
S C A N S PE ED
C L E A R SC AN
R U N S C AN
B A C K
E X I T
1
N O T U S ED
N O T U S ED
3 0 / S E C
C A N C E L
P A T T ER N SE TU P
-----------------------------
P A T T ER N NO .
C L R P A TT ER N
R U N P A TT ER N
< E D I T PA TT ER N >
B A C K
E X I T
1
C A N C E L
From the dome camera setup menu, use the
joystick to highlight PATTERN SETUP and
key: NEAR
PATTERN NO. (1 - 4) - The pattern number
currently being modified.
CLR PATTERN - the currently selected pattern
can be deleted
RUN PATTERN - runs the currently selected
pattern for testing purposes
<EDIT PATTERN> - allows the operator to
program a patten tour
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
Pattern setup
E D I T P AT TE RN 4
-----------------------------
M O V E T O ST AR T PO S I T I O N
[NEAR:START /FAR:CANCEL
E D I T P AT TE RN 4
[NEAR:SAVE /FAR:DELETE]
From the pattern setup menu, use the joystick
to highlight EDIT PATTERN and key: NEAR
Position the speed dome to the desired
starting point and key: NEAR
Move the dome to the various positions and
zoom levels required for the pattern. The white
squares at the top of the display show
remaining storage and disappear as the
pattern is recorded.
To save the pattern, key: NEAR
To abandon pattern programming, key: FAR
Note: Pattern tour memory is only used when
movements are recorded. Pauses between
movements, regardless of time, do not use
pattern tour memory
Edit pattern
11

From the dome camera setup menu, use the
joystick to highlight GROUP SETUP and key:
NEAR
GROUP NO. (1-8) - shows the group number
currently being modified.
CLEAR GROUP - the currently selected group
can be deleted
RUN GROUP - runs the currently selected
group for testing purposes
<EDIT GROUP> - allows the operator to
program the group functions
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
From the group setup menu, use the joystick
to highlight EDIT GROUP and key: NEAR
To edit the group, key: NEAR again
Header explanation:
NO - the item number (between 1 & 20)
ACTION - the specific action for this item
### - the action number (eg if ACTION is set
to PRESET, this value can be between 1 &
128
DWELL - the amount of time before the next
action in the list is called
OPT - for PRESET actions, this value is the
speed at which the dome moves to the preset.
For swing and PATTERN, this value is the
number of times the action is repeated before
the next action is called
Move the joystick up and down to choose the
group item to modify and key: NEAR. The
ACTION is highlighted in white
Move the joystick up and down to change the
action type between NONE, PRESET, SWING
and PATTERN.
Move the joystick left and right to select and
edit values for ###, DWELL & OPT.
From the main menu, use the joystick to
highlight PASSWORD SETUP and key: NEAR
CHECK PASSWORD (ON/OFF) - when set to
ON, the correct password must be entered to
access the speed dome setup menus
<EDIT PASSWORD> - allows the current
password to be changed
Key NEAR to save this item and continue
adding more items as necessary, or key FAR
to exit.
Group setup Edit group
Password setupPassword setup
Edit group
G R O U P SE TU P
-----------------------------
G R O U P NO .
C L E A R GR OU P
R U N G R OU P
< E D I T GR OU P>
B A C K
E X I T
E D I T G RO UP 1
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
N O A C T IO N ## # DW E L L O P T
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 N O N E
2 N O N E
3 N O N E
4 N O N E
5 N O N E
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
B A C K
C A N C EL [ NE AR : E D I T ]
P A S S WO RD S ET U P
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
C H E C K PA SS WO R D O F F
< E D I T PA SS WO R D >
B A C K
E X I T
P A S S WO RD S ET U P
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
C H E C K PA SS WO R D O F F
< E D I T PA SS WO R D >
B A C K
E X I T
E D I T G RO UP 1
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
N O A C T IO N ## # DW E L L O P T
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 P A T T ER N
2 P R E S ET
3 S W I N G
4 P R E S ET
5 P R E S ET
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
B A C K
C A N C EL [ NE AR : E D I T ]
1
C A N C E L
12
1
5
3
1 0
4
1
3 6 0
8
1 1 0
5 5
0 0 : 0 3
0 0 : 0 8
0 0 : 0 3
0 0 : 1 5
0 1 : 3 0
Edit password
E D I T P AS SW OR D
-----------------------------
[ ]
- - - - -- -- --
1 2 3 4 56 78 90 O K
A B C D EF GH IJ C A N C E L
K L M N OP QR ST
U V W X YZ ab cd
e f g h ij kl mn
o p q r st uv wx
y z < > -/ :.
Backspace
Space
From the password setup menu, use the
joystick to highlight EDIT PASSWORD and
key: NEAR
The solid white square shows the current
cursor position.
This flashing white square shows the currently
selected character.
Move the joystick up / down / left / right to
choose the required character and key: NEAR
to insert it in the password. The solid white
square moves to the next cursor position.
Repeat until password entry is complete.
If a mistake is made, use the joystick to select
the backspace ( ) and key: NEAR. The cursor
moves back one square.
Select OK to save the password or CANCEL
to lose changes and key: NEAR to exit
Remember: When CHECK PASSWORD is set
to ON, each time the operator attempts to
enter the speed dome setup menu, the above
screen will be displayed. The correct
password must be entered to continue with
menu setup

13
Using the speed dome features
Once the pattern tours,swing functions and groups have been
programmed in the speed dome setup menu, they can all be
accessed directly from the PTZ control equipment by using the
following sequences.
1. To start a pattern tour press:
SHOT - 13X - ENTER
Where X is a pattern tour number between 1 & 4
The selected pattern tour will run indefinitely until a manual movement is made by the
operator or an alarm input is received.
2. To start a swing function, press:
SHOT - 14X - ENTER
Where X is a swing function number between 1 & 8
The selected swing function will run indefinitely until a manual movement is made by the
operator or an alarm input is received.
3. To start a group, press:
SHOT - 15X - ENTER
Where X is a group number between 1 & 8
The selected group will run indefinitely until a manual movement is made by the operator or
an alarm input is received.
System initialise
S Y S T EM I NI TI A L I S E
- - - - -- -- -- - - - - - - - - - -- -- -- - - - -
C L E A R AL L DA TA
C L R D I SP LA Y SE T
C L R C A ME RA S ET
C L R M O TI ON S ET
C L R E D IT D AT A
R E B O OT C AM ER A
R E B O OT S YS TE M
B A C K
E X I T
From the main menu, use the joystick to
highlight SYSTEM INITIALISE and key: NEAR
CLEAR ALL DATA - selecting this option will
perform a full factory reset on the speed
dome. All presets, swing functions, patterns,
groups and privacy zones will be erased
CLR DISPLAY SET - this option will reset the
on screen display settings to factory default
and erase all privacy zones
CLR CAMERA SET - this option will reset the
camera module settings to factory default
CLR MOTION SET - this option will reset the
motion menu settings to factory default
CLR EDIT DATA - this option will erase all
presets, swing functions, patterns and groups
Highlight the item to modify and key: NEAR
Use the joystick to change the setting to ON
and key: NEAR to run or: FAR to cancel.
N O
N O
N O
N O
N O
N O
N O

Heater
Thermostat
Fan
Thermostat
Shield Mount
Tilt Motor
Inner dome cover
Zoom Module
Dome Cover
Pan Motor
Sunshield
Dome Housing
Bracket Mount
Base
Bracket Upper
Cover
Seal
Housing Upper Cover
Bracket Joint
PCB
Parts and dimensions
230
33
3353140
19
156
325
201
14
Appendix Of Outdoor High Speed Dome System

24V AC PSU
RS-485
Cable
Video Cable
Alarm Input
Cable
Power Cable
Alarm Sensor
Siren / Light etc.
Siren / Light etc.
power source
Alarm Output
Cable
Wiring schematic
15

16
Fan & Heater
Current(A)
Voltage
Power Consuption
Trigger Temperature
Fan Heater
0.1A 0.67A
12V
12V
1.2W 8W
More than40℃Less than5℃
Brackets for option
Wall bracket
Pendent Bracket Corner Bracket
Pole Bracket
(V)

17