TBK vision TBK-6311SDI User manual

Rev 2.03 dated Dec. 04, 2006
HI-SPEED DOME CAMERA

2

3
Warning & Caution
What’sintheBox?
General Features
NamesofEachPart
Installation
A.ConnectionMethods
B. Ceiling Mount Type
C. Embedded Mount Type
Quick Operating Keys
Diagnostic
OSD Menu Setting
A.OSDMenuTable
B.DOMESET
C.CAMERASET
D. PRESET
E.AUTOSCAN
F. TOUR SET
G. PRIVACY SET
H. PATTERN SET
I. ALARM SET
J. SECTOR SET
DIPSwitchSetting
A.IDSetting(DIPSW1)
B. 485 Termination (DIP SW2)
C. Protocol (DIP SW2)
D. Baud Rate Setting (DIP SW2)
Trouble Shooting
Specification
Dimensions
CONTENTS
4
4
5
6
7
9
11
12
14
15
16
20
23
24
25
26
27
28
29
30
32
32
32
33
34
35

4
WARNING & CAUTION
If you fail to read this information and
handle the product incorrectly, death or
serious injury may occur.
1. Camera
2. Ceiling Mount Bracket
3. Wrench
4. Screw (Ø 3x6 screw 2EA,
Ø4x16 screw 5EA)
5. Safety Wire
6. Manual
7. Ceiling Cover
8. Cable ties
9. Terminal Block
(2Pin 2EA
3Pin, 5Pin, 6Pin 1EA)
The unit should be installed by trained
Always stop using when the product emits
smoke or abnormal heat.
Never install the product in area exposed
water, oil or gas.
Never install the product on a ceiling that
cannot hold its weight.
Never touch the power cord with wet hands.
Clean only with dry cloth.
Never install the product in extreme high or
low temperature.
Never drop hit strongly nor vibrate the
product.
Never expose the product to direct sunlight
or severe ray.
Never touch the front glass of the product.
Never install the product in areas exposed to
rain or water
What’s in the Box?
This symbol is intended to alert the user to
the presence of un-insulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

5
GENETAL FEATURES
NAMES OF EACH PART
World most silent speed dome camera
Equipped with silent and smooth timing belt and special
gear, low-noisy-technology enhances durable quality of the
camera by reducing the mechanical vibration. This
camera is the perfect match, both indoor and outdoor, for
demanding security and monitoring burglars.
0.024°dome system accuracy with 1/8
micro step
With 0.024°technical accuracy, camera provides excellent
sensitive and delicate controlling on preset mode by
adapting 1/8 micro step and twin gear system
Reliable RAM-Material
The mechanical stabilization improves the durability and
long life time of the camera by using reliable materials
especially, stepping motor, slip ring, timing belt and power
condenser. This camera case is made of fire resisting
material that approved UL grade 94 V-0. It is useful for
indoor environment concerning about the fire accident
Compensation function: preset position
The function provides absolute preset position even if the
camera is moved by low-frequency vibration, wind and any
impact.
Slip Ring for long life time (20milion
rotate ring tested)
Equipped with slip ring is passed by up to 20 millions rotate
ring test within 6 months
Power misconnection protection on 485
terminals
This protection function prevents the communication
terminal from being out and trouble when power source
falsely connects to the RS-485 terminals. Hi speed dome
got a patent for power misconnection protection on RS-485
terminal
Filter changeable True Day/Night
Surveillance with optimum picture is possible owing to filter
changeable Day/Night (ICR block filter) function and DSS.
Auto IR cut filter removable function is auto controlling the
operation such as color picture plus infrared cut filter during
the day and black and white picture plus filter elimination at
night
Quick Operation Keys
This camera provides quick functional keys in other to be
easily controlled by any other controller or DVR.
Various Surveillance Functions
Auto Scan repeats pan and tilt between two preset
positions with different speed and dwell time.
8 Group Tour up to 8 Programmable Group tours
available and each group is consisting up to 60 presets
step with different speed and dwell time with 16
characters.
165 Preset positions up to 165 programmable
preset positions are available with 16 characters
8 Patterns up to 8 programmable user-defined patters
are available with 16 characters and each one is
consisting 50 seconds, total 400
8 Sectors up to 8 programmable user-defined sectors
are available with 16 characters
24 Privacy Masking Zones up to 24 programmable
user-defined privacy masking zones are available with
16 characters (18X, 26X, 36X only: 23X, 30X has 4
privacy masking zones)
4 Alarm input and 2 relay out up to 4 alarms and
2 relay out available to match with preset, tours,
patterns.
300°/S 200°/S on Preset speed
The 360°full pan function moves through a maximum of
350°/sec., enabling you to quickly pinpoint the spot you
want to watch. Tilt speed provides through a maximum
250°/sec on preset. On preset mode, the camera is set
up to 300°/sec
200°/S – Manual speed
This camera provides up to 200°/sec of manual speed
and it’s adjustable from 100°/sec to 200°/sec
1/4” Sony Ex-View CCD
Equipped with Sony Ex-view HAD CCD technology,
these particular cameras provide excellent sensitivity
and low smear levels (18X 26X 36Xonly / 23X, 30X has
Sony Super HAD CCD)
Multiple languages and protocols
To convenience for the customers, this camera provides
several languages and protocols including English,

6
1. Bubble
2. Lock Screw
3. DIP Switch 1
4. DIP Switch 2
5. Camera
6. Lock Holder
7. Power
8. Video Output
9. Loop RX
10. Loop TX
11. Power LED
12. Aux
13. Alarm
14. Mount Holder
NAME OF EACH PART

7
A. CONNECTION MATHOD
A-1 To separate camera body
Loosen Lock Screw 2mm to the counterclockwise using the wrench.
(Don’t pull out the screw) (FIG.2)
Separate the upper body from the lower body rotating counterclockwise. (FIG.3, 4)
A-2 After separating set DIP switches. (Refer to the page 29, 30 and 31)
A-3 To assemble camera body
Rotate the upper body clockwise to assemble both bodies. (FIG.5, 6)
Screw up using wrench clockwise. (FIG.7)
zDon’t screw tightly. It can be the cause of defect.
INSTALLATION
FIG.2 FIG.4 FIG.3
FIG.6FIG.5 FIG.7

8
A-4 Alarm :4 Alarm input
A-5 AUX :DC 12V 1A can be used as an AUX terminal.
Turning on the light and remote control are possible using AUX.
A-6 TX :TX transmits Data signal received from RX to other equipment.
TX is convenient terminal for connection with Daisy Chain.
A-7 RX :RX are received Control Signal from controller or DVR.
A-8 Video out: BNC connector
A-9 Power :AC 24V 1.0A adaptor
* Don’t connect power source to Center terminal of Power.
A-10 Power on LED
INSTALLATION
FIG.8

9
B. CEILING MOUNT TYPE
B-1 Select a ceiling board strong enough to hold the weight approx. 2kg.
B-2 Prepare a Ø145mm hole in the ceiling board. (FIG.9)
Fix the safety wire to a suspension to prevent camera from falling.
Other side of safety wire is fixed to the safety wire hole. (FIG.10)
B-3 Fix the Ceiling Mount to the Ceiling with 4 screws (Ø4.0mm tapping screw). (FIG.11)
B-4 Tie the wire using the cable ties. (FIG.12)
B-5 Let the wires to be put into the square hole.
Place the Camera Mount Holder on the Bracket Mount Hole. (FIG.12)
To insert them easily, keep 10° interval of Lock Holder1 and Lock Holder2. (FIG.13)
MOUNTING HOLE
LOCK HOLDER.1
FIG.10
SAFETY WIRE
SUSPENSION
CEILING BRACKET
SCREW ( 4.0)
FIG.11
COVER HOLE
SAFETY WIRE HOLE
145.0 mm
FIG.9
FIG.12
LOCK HOLDER.2
LOCK HOLDER.1
CABLE TIE
MOUNT HOLDER
INSTALLATION

10
B-6 To assemble, rotate the Camera clockwise by 10°. (FIG.13)
B-7 Screw up Lock Holders with screws (M3).
B-8 Assemble the Cover.
Fix three Cover Locks to three Cover Holes rotating clockwise. (FIG.15)
FIG.15
COVER
COVER LOCK
COVER HOLE
10°
LOCK HOLDER.2
FIG.13
LOCK HOLDER.1
FIG.14
SCREW (M3.0)
INSTALLATION

11
C. EMBEDDED MOUNT TYPE
C-1 Prepare an Ø190mm hole in the ceiling board.
Fix the safety wire to a suspension to prevent camera from falling.
Other side of safety wire is fixed to the safety wire hole. (FIG.16)
C-2 Fold the Lock Levers then insert the Bracket into the Ceiling Hole.
Fix the Bracket to the ceiling using the driver. (FIG.17)
C-3 Hereafter installation is same way of Ceiling Mount Type. (Refer to the page 9, 10)
LOCK LEVER
FIG.17
SAFETY WIRE HOLE
190.0 mm
LOCK LEVER
LOCK LEVER
FIG.16
EMBEDED MOUNT
LOCK LEVER
FIG.18
SCREW (M3.0)
INSTALLATION

12
This dome provides three protocols mainly as Pelco D, Pelco P and Maxpro.
These protocols are able to use with other DVR or Controller if the equipment has the above protocols.
Default setting of this dome is Pelco D / P (auto detection) with 2400 bps (baud rate).
[PELCO D/P PROTOCOLS]
As the merit of this dome, it has lots of function keys to support the following functions.
Selectable Preset number from 1~64 and 100~200, other keys are for function operation keys.
For example, to enter OSD MENU, press the button 95 +PRESET.
<Quick Operation Key Table 1>
Numbe
r
Note Function
1~64,100~200 +Prese
t
Preset Executing Preset 1 ~ 64, 100~200
65 +Preset Preset Status Display Preset Status
66 +Preset Auto Scan Executing Auto Scan
67 +Preset Auto Flip Selectable On/Off in Auto Flip mode
68 + Preset Camera Reset Re-setting Zoom camera module
69 + Preset DSS Selectable On/Off in Digital Slow Shutter function
70 + Preset VIB CORR Selectable On/Off in Picture Stabilization function
71~78 + Preset Group Tour Executing Group Tour #1 ~ #8
81~88 + Preset Pattern Executing Pattern #1 ~ #8
91 + Preset Zero Position Searching Pan / Tilt Zero Position
92 + Preset Freeze Select Freeze image when camera is working
93 + Preset BLC Selectable On/Off in BLC function
94 + Preset Day / Night Selectable Day / Night / Auto Mode
95 + Preset OSD Entering OSD Main Menu
96 + Preset Focus Adjust Focus adjust
97 +Preset Alarm Selectable Enable/Disable all Alarms
98 +Preset AUX 1 Selectable On/Off in Aux1
99 +Preset AUX 2 Selectable On/Off in Aux2
<Quick Operation Keys Table 2> Use these function keys if controller has these keys>
* 65 + preset:” Status Report” is displayed, if user wants to remove this screen, press Focus Near button.
* 70 + preset: This feature provides picture stabilization image and it is by EX980S (P) module only.
This feature is operating by preset number but not included in OSD main menu. This is optional function due
to zoom module
* 92 + preset: This feature is possible to freeze the current monitoring image during tour, auto scan or
Menu Function
Tilt Up / Down Sub menu cursor moves up / down
Pan Left / Right Enter to the sub menu or status change or decrement
Focus Near Using for Enter key when user select YES or NO
Focus Far Using for function changing keys when set coordinate
Zoom Tele Status cursor to the right
Zoom Wide Status cursor to the left
QUICK OPERATING KEYS

13
pattern operation. When press 92 + preset button, the image is suddenly freeze but the camera is still
working as per operation such as tour, pattern or auto scan. To return operating image, press 92 + preset
button again. This feature is operating by preset number but not included in OSD main menu.
* Due to Zoom camera module, OSD Menu provides not every feature. In this case, “Not available” is
displayed on the monitor.
[MAXPRO PROTOCOL]
If user wants to choose Maxpro Protocol, the user may change the dip switch first.
(Refer to Page #32 DIP SWITCH SETTING - PROTOCOL)
Baud Rate: 9600 (Maxpro default)
Maxpro protocol is almost same as Pelco D/P protocol operating system but some special features are
different way as noted below’
<Quick Operation Key Table 1>
Numbe
r
Note Function
1~64,100~200 +Prese
t
Preset Executing Preset 1 ~ 64, 100~200
67 +Preset Auto Flip Selectable On/Off in Auto Flip mode
69 + Preset DSS Selectable On/Off in Digital Slow Shutter function
80~85 + Preset Pattern Executing Pattern #1 ~ #6
86 + Preset Auto Scan Executing Auto Scan
87~89 + Preset Group Tour Executing Group Tour #1 ~ #3
90 + Preset OSD Entering OSD Main Menu
91 + Preset Zero Position Searching Pan / Tilt Zero Position
92 + Preset Freeze Select Freeze image when camera is working
93 + Preset BLC Selectable On/Off in BLC function
94 + Preset Day / Night Selectable Day / Night / Auto Mode
95 + Preset OSD Entering OSD Main Menu
96 + Preset Focus Adjust Focus adjust
97 +Preset Vir. Corr. Selectable On/Off in Vibration Correction function
98 +Preset AUX 1 Selectable On/Off in Aux1
99 +Preset AUX 2 Selectable On/Off in Aux2
<Quick Operation Keys Table 2> Use these function keys if controller has these keys>
zDue to Zoom camera module, OSD Menu provides not every feature. In this case, “Not
available” is displayed on the monitor
Menu Function
Tilt Up / Down Sub menu cursor moves up / down
Pan Left / Right Enter to the sub menu or status change or decrement
Focus Near Using for Enter key when user select YES or NO
Focus Far Using for function changing keys when set coordinate
Zoom Tele Status cursor to the right
Zoom Wide Status cursor to the left
QUICK OPERATING KEYS

14
When Power on, POWER ON, LED ON in the rear side and DIAGONOSTIC is operated.
The following messages are displayed on the monitor.
A. Pan Origin Test
Zero point of Pan is found after Panning test.
B. Tilt Origin Test
Zero point of Tilt is found after Tilting test
C.TX connection Test
Wait for 60 seconds for TX Connection Test,
During 60 seconds, the camera is must received a signal by any control equipment as DVR or controller.
Then Ok is displayed then automatically verifying TX Connection Test.
* If “No Tested” is displayed in the test,
- The result which is not received any signal from DVR or controller
- Wrong connecting way such as the protocol, baud rate or RS-485 connection. The use may check the
install way carefully.
D. Camera Comm. Test
Communication test with the camera is automatically checked.
OK should be displayed in these four tests in the first installation.
All the above Tests are OK, “NOW EEPROM CHECKING” and “ALL DATA INITIALIZING” is displayed
and the camera is ready to operate.
DIAGNOSTIC
CAMERA ID : 001
BAUD RATE : 2400 BPS
WAITING………
PAN ORIGIN TEST OK
TILT ORIGIN TEST OK
TX CONNECTION TEST OK
CAMERA COMM TEST OK

15
A. OSD MENU TABLE
OSD MENU SETTING
MAIN MENU DOME SETUP CAMERA SET AUTO SCAN TOUR PRAVACY PATTERN ALARM SECTOR EXIT
DOME SET CAMERA ID : CAM1□□□□□□□□□□□□
RECOVER : OFF MANUAL SPEED : 150°/S AUTO FLIP : OFF ZOOM SPEED : FAST
ALARM : DISABLE LANGUAGE : ENGLISH [NEXT PAGE] SAVE AND EXIT
CAMERA SET
FLICKER : OFF/ON MIRROR : OFF/ON APERTURE : 10 D ZOOM : OFF/ON WB MODE : AWB MODE PIC FLIP : OFF/ON BLC : OFF/ON D/N MODE : AUTO DSS MODE : OFF/ON EXIT
PRESET SET PRESET NO: 001 PRESET ID: PRESET01□□□□□□□□□ PAN:XXX.X.XX.X TILT:XXX.X.XX.X SAVE EXIT
AUTO SCAN SET
START ANGLE : XXX.X.XX.X END ANGLE : XXX.X.XX.X DIRECTION : CW ENDLESS : OFF/ON SPEED : QUICK DWELL TIME : 03 SAVE AND EXIT EXIT
SECTOR SET SECTOR NO : 01 SECTOR ID : SECTOR01□□□ SECTOR START: XXX.X.XX.X SECTOR END : XXX.X.XX.X SAVE EXIT
PATTERN SET
PATT NO. : 01 PATT TITLE PATTERN01□□□ DATA FILL : 100% SAVE EXIT
ALARM SET
ALARM NO. : 01 ALARM INPUT : OFF ALARM ACT : 01 SAVE EXIT
PRIVACY SET
PRIVACY NO. : 01 DISPLAY ACTION SAVE EXIT
TOUR SET TOUR NO. : 01 TOUR TITLE : TOUR01□□□□□□ TOUR STEP : 01 PRESET NO : 01 DWELL TIME : 10 SPEED : 300°/S SAVE AND EXIT EXIT
NEXT PAGE
[OSD DISPLY] [SYSTEM STATUS] [INITIALIZATION] [PREVIOUS PAGE]
[INITIALIZATION]
[TOUR CLEAR] [PRESET CLEAR] [SECTOR CLEAR] [PRIVACY CLEAR] [PATTERN CLEAR] [LOAD OPTIMIZED DEFAULT
[SYSTEM STATUS] PROTOCOL : PELCO D,P BAUD RATE: 2400BPS FIRMWARE VER.:2.00 UPGRADED DATE: 02.28,06 CAMERA MODULE: EX980P [PREVIOS PAGE]
OSD DISPLAY
CAMERA ID: OFF/ON PRESET ID: OFF/ON SECTOR ID: OFF ON COORDINATE:ON/OFF [PREVIOUS PAGE]

16
To enter OSD Menu, press the button 95+Preset (Maxpro 90+Preset) then OSD Main Menu is
displayed.
* Use the joystick up down to move the position and left right to make selection
B. Dome Setup
To enter Dome setup, use the joystick right to move when cursor on dome setup.
B-1. DOME SET - CAMERA ID
To set camera ID, select up to 16 characters using Joystick to the left or right.
Press ZOOM TELE button moves to the next character from the left to the right direction and
ZOOM WIDE button moves to the next character from the right to left direction (Space displays
when appears)
B-2. DOME SET - RECOVER
This feature allows the dome to activate final specified operation (auto scan, group tour, preset,
pattern or sectors) after a programmed time of inactivity even power shut down then turn it on
again. Recover time can be programmed from 15 second to 99 seconds and the default setting
OSD MENU SETTING
DEFAULT SETTING
MAIN MENU
DOME SETUP
CAMERA SET
AUTO SCAN
TOUR
PRAVACY
PATTERN
ALARM
SECTOR
EXIT
DOME SET
CAMERA ID : CAM1□□□□□□□□□□□□
RECOVER : OFF
MANUAL SPEED : 150°/S
AUTO FLIP : OFF
ZOOM SPEED : FAST
ALARM : DISABLE
LANGUAGE : ENGLISH
[NEXT PAGE]
SAVE AND EXIT
EXIT

17
is OFF
B-3. DOME SET - MANUAL SPEED
Manual Speed of Pan/Tilt is selectable from 100°/sec up to 200°/sec. The default setting is
150°/sec
B-4. DOME SET - AUTO FLIP
Auto Flip is available and the default setting is OFF. Move joystick right or left direction is for
selecting OFF or ON. The default setting is OFF. This feature is working as 67 + preset button.
B-5. DOME SET – ZOOM SPEED
Zoom speeds are selectable FAST or SLOW mode. Move joystick to the right direction for
selecting FAST or SLOW. The default setting is FAST.
B-6. DOME SET – ALARM
All alarms are available after set as ENABLE Mode. Move joystick to the right or left direction for
selecting ENABLE/DISABLE. The default setting is DISABLE Mode and this feature is working as
97 + preset button.
B-7. DOME SET - LANGUAGE
Multiple languages are selectable here including English, Italian and Polish. Move joystick to the
right or left direction to select language. The default setting is ENGLISH.
B-8. DOME SET – [NEXT PAGE]
B-8-1. DOME SET – [NEXT PAGE] – SYSTEM LOCK
Password protection provides keeping memorized data and it cannot be adjust by anybody without
password. In order to enter [PASS WORD] page, system lock status is must set as ON. Move
joystick to the right or left direction to select ON. The default setting is OFF.
B-8-2. DOME SET – [NEXT PAGE] – [PASSWORD]
To enter this page for set a password, move joystick to the right direction. The password is must set
by preset number from 001 to 255 expect the quick operation keys as shown “A. OSD MAIN MENU
TABLE (PAGE 14) The default setting is BLANK.
OSD MENU SETTING
DOME SET
SYSTEM LOCK: : OFF
[PASS WORD]
[OSD DISPLAY]
[SYSTEM STATUS]
[INITIALIZATION]
[PREVIOUS PAGE]
DEFAULT SETTING

18
Press any number from 001~200 with preset button on password typing location and again it on
confirm location. Then “CONFIRMED” is displayed on the monitor and the menu will change to
the previous page automatically.
<CONFIRMED> <CANCELLED>
If user press wrong preset number between PASSWORD and CONFIRM, “CANCELLED” is
displayed on the monitor and the menu will return to the previous page automatically if user failed 3
times.
* After set a Password, the operator must press memorized password in order to enter OSD MAIN
MENU, or to change the data which is memorized originally.
* The operator must remember the password for the operation and manufacturer provides not
memorized password.
B-8-3. DOME SET – [NEXT PAGE] – [OSD DISPLAY]
OSD ID displayed after set ON in here and it can be hiding if selected OFF. Move joystick to the
right or left direction in order to select OFF/ON when the cursor is located each item.
B-8-4. DOME SET – [NEXT PAGE] – [SYSTEM STATUS]
This page shows the information of this camera.
OSD MENU SETTING
ENTER PASSWORD
BY ENTERING PRESET CODE
PASSWORD ***
CONFIRM ***
ENTER PASSWORD
BY ENTERING PRESET CODE
PASSWORD ***
CONFIRM ***CANCELLED
ENTER PASSWORD
BY ENTERING PRESET CODE
PASSWORD ***
CONFIRM ***CONFIRMED
OSD DISPLAY
CAMERA ID : OFF
PRESET ID : OFF
SECTOR ID : OFF
COORDINATE : ON
[PREVIOUS PAGE]
DEFAULT SETTING

19
- Protocol and baud rate are shown due to the dip switch setting (Refer to page 30, 31 and 32)
- Firmware version and upgraded date will change if upgraded.
- Camera module is settling as follows
* 18X : SONY ZOOM MODULE # EX480C
* 26X : SONY ZOOM MODULE # EX980C / EX980CS
*36X : SONY ZOOM MODULE # EX1000C / EX1010C
* 23X : SAMSUNG TECHWIN ZOOM MODULE #
* 30X : SAMSUNG TECHWIN ZOOM MODULE #
B-8-5. DOME SET – [NEXT PAGE] – [INITIALIZATION]
To clear all memorized data for tour, preset, sector, privacy or pattern, move joystick to the right
direction when the cursor is on [INITIALIZATION]
- To clear memorize any data, move joystick to the right direction when cursor is on each
item.
Press FOCUS NEAR button when the cursor is at YES in order to clear memorized data.
SYSTEM STATUS
PROTOCOL : PELCO , P
BAUD RATE : 2400 BPS
FIRMWARE VER. : 2.01
UPGRADED DATE : 02.28,06
CAMERA MODULE : EX980P
[PREVIOUS PAGE]
INITIALIZATION
[TOUR CLEAR]
[PRESET CLEAR]
[SECTOR CLEAR]
[PRIVACY CLEAR]
[PATTERN CLEAR]
[LOAD OPTIMIZED DEFAULT]
[PREVIOUS PAGE]
DEFAULT SETTING
TOUR CLEAR
ARE YOU SURE? YES NO
TOUR CLEAR
OSD MENU SETTING

20
Then flickered each item such as Tour, preset, sector and so on are displayed on the
monitor about 2~3 seconds. After this process, the menu is return to the previous page.
* [PRESET CLEAR], [SECTOR CLEAR], [PRIVACY CLEAR], [PATTERN CLEAR] are same as
[TOUR CLEAR].
- To clear all data and wants returning to factory default, move joystick to the right direction when
cursor is at [LOAD OPTIMIZED DEFAULT] to enter the above page.
- Move joystick to the right or left direction in order to select YES, press FOCUS NEAR button.
- Then “NOW EEPROM CHECKING” and “ALL DATA INITIALIZING” is displayed about 5~7
seconds and then the menu is return to the previous page automatically.
B-9. DOME SET – [NEXT PAGE] – SAVE AND EXIT
To saving the memorized data and escape this page, move joystick to the right direction
when cursor is at SAVE AND EXIT.
B-10. DOME SET – [NEXT PAGE] – EXIT
In order not to save any data and wants to escape this page, move joystick to the right
direction when cursor is at EXIT
LOAD OPTIMIZED DEFAULT
ARE YOU SURE? YES NO
NOW EEPROM
CHECKING
ALL DATA
INITIALIZING
OSD MENU SETTING