TCP SMAWHTOW2000WBHN2116 User manual

SMART WIFI TOWER FAN
Thank you for purchasing this TCP Smart Wi-Fi Hot & Cool Tower Fan.
The TCP Smart WiFi Tower Fan offers an efficient and quick heating solution which is
portable and easy to use. Control your heating exactly as you desire either using the control
panel situated on the heater or mobile phone using the TCP Smart App and /or voice control
via Alexa or Google Nest.
MODEL
POWER
SMAWHTOW2000WBHN2116
AC220-240V 50-60Hz 2000W Class II
USER INSTRUCTIONS
IMPORTANT: Read these instructions fully before using the heater. Retain these instructions for future
reference.
SAFETY INSTRUCTIONS (to be read before operating the heater)
1 Before using set the power-level switch which is located at the back of the heater to
“0”.
2 CAUTION: Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present. Children 3 years
and younger should be continually supervised when in close proximity to the heater. Children
aged 3 to 8 years shall only switch on/off the appliance provided that it has been placed or
installed in its intended normal operating position and they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children aged 3 to 8 years shall not plug in, regulate and clean the appliance or perform user
maintenance.
3 Use this heater on a flatorhorizontal and stable surface.
4 Keep the power cord away from the hot body of the heater.
5 Indoor use only.
6 Do not place the heater on carpets with a very deep pile.
7 Do not place the heater close to curtains or furniture in order to avoid a fire hazard.
8 Do not insert any object through the air grilles of the heater.
9 Do not use the heater in areas where flammable liquids are stored or where
flammablefumes may be present.
10 Always unplug the heater when moving it from one location to another.
11 Do not use this heater if it has been dropped;
12 Do not use if there are visible signs of damage to the heater;
13 Do not leave the heater switched on when your property is vacant.

WARNINGS
- In order to avoid overheating, do not cover the heater.
- Always use the heater in an upright position.
- Do not use the heater to dry your laundry.
- Never obstruct the intake and outlet grilles to avoid the danger of overheating.
- Do not place it up against walls, furniture, curtains, etc.
- If the supply cord is damaged, it must be replaced by the manufacturer, their service
agent or a similarly qualified person in order to avoid a hazard.
- Do not use this heater in the immediate surroundings of a bath, a shower or a
swimmingpool.
Assembly
Parts and components:
To fit the base to the body of the
heater. Align the 4 clips on both
sides of the base. Push
together until both sides sit
flush. Place on the bottom of
the heater and secure using the
plastic bolt provided.

Control Panel
OPERATING THE HEATER
Note：It is normal when the heaters are turned on for the first time, or when they are turned on after a long
period of time not being used, the heaters may emit some smell and fumes. This will disappear when the
heater has been on for a short while.
Choose a suitable location for the heater, taking into account the safety instructions above. Insert the
plug of the heater into a suitable socket.
On/Off
Press once to turn the device on.
This feature can be performed using the TCP Smart App
Mode
Press to cycle through the three available mode: Cool, Low Heat and High Heat.
Oscillation
Press the swing button to activate or deactivate the oscillation function. When it is activated, the oscillation
light indicator will turn on and air flow will be moved from left to right.
This feature can be performed using the TCP Smart App
Timer button
Press the timer button repeatedly to increase the operating time by 1-hour intervals. The time can be set
from 1 to 12 hours. The display will show the remaining operating time. When the display is showing the
timer duration the symbol will be displayed next to the timer. To cancel the timer, press the timer button
repeatedly until the 00 is displayed.
This feature can be performed using the TCP Smart App

Temperature button
Press the temperature button repeatedly to increase the target room temperature, from 15 to 40°C. Once
the temperature is set, the digits will flash for 3 seconds and then the display will show the current room
temperature. Once the target temperature is reached, the device will automatically switch to fan mode.
The device features a safety push button on its base, which will turn the device off if it is accidentally tilted.
This feature can be performed using the TCP Smart App
Colour Button
Press to cycle through the options for the ambient light –Off, Blue, Red or Purple. The light can be
operated independently of the Fan.
This feature can be performed using the TCP Smart App
CLEANING THE HEATER
Always un-plug the heater from the wall socket and allow it to cool down before cleaning. Clean the
outside of the heater by wiping with a slightly damp cloth and buff with a dry cloth. Do not use any
detergents or abrasives and do not allow any water to enter the heater.
STORING THE HEATER
When the heater is not used for long period of time it should be protected from dust and stored in a
clean dry place.
CORRECT DISPOSAL OF THIS PRODUCT
WARRANTY INFORMATION
The manufacturer provides warranty in accordance with the legislation of the customer's own country of
residence, with a minimum of 2 years, starting from the date on which the appliance is sold to the end user.
The warranty only covers defects in material or workmanship. The repairs under warranty may only be
carried out by an authorized service centre. When making a claim under the warranty, the original
purchase receipt (with purchase date) must be submitted.
The warranty will not apply in cases of:
-Normal wear and tear
-Incorrect use, e.g. overloading of the appliance, use of non-approved accessories
-Use of force, damage caused by external influences
-Damage caused by non-observance of the user manual, e.g. connection to an unsuitable mains supply or
non-compliance with the installation instructions
-Partially or completely dismantled appliances

CERTIFICATION CONFORMITY
Hereby, Technical Consumer Products Ltd declares that the radio equipment type TCP Smart Wifi Tower
Fan 2000W –White is in accordance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address –
www.tcpi.eu.
REGISTERED OFFICES
TCP UK Ltd, 1 Exchange Court, Cottingham Road, Corby, Northants, NN17 1EW.
TCP France, Quai Gabriel P’ri, 1, Joinville Le Point, France, 94340.

CONNECTING THE APPLIANCE TO WIFI
Use the QR code below to download the TCP Smart App for control of the heater remotely.
To control the heater using the TCP Smart App the unit must be turned on. Before you get started you
will need the following:
Smart device such as a mobile phone or tablet
Access to the Google or Apple app store, log on and passwords
The name of your Wi-Fi network and password to your Wi-Fi network
Confirm your home Wi-Fi router is running on 2.4Ghz and not 5Ghz. If you are unsure, please
consult your broadband provider for details on how to change the settings.
Turn off any Wi-Fi extenders during set up
Check you do not have any limitations on the number of devices with your broadband provider
Please note: Our products do not work on 5Ghz only 2.4Ghz.
For instructions on how to connect to Amazon Alexa or Google Nest please visit
https://www.tcpsmart.eu/how-to-alexa-google-nest
With the heater turned on, hold down the On/Off button until it beeps and the LED light
above the button blinks quickly, the device is now in paring mode. In the TCP Smart App, enter
your WiFi password and follow the instructions in the App to connect.

USING THE APPLIANCE WHEN CONNECTED TO WIFI
Note: screen appearance may vary
DEVICE CONTROL SCREENS
1 Switch –Power on and off
2 Mode –to select Cool, Low Heat or High Heat
3 Timer –to select time countdown duration
4 Settings –to select oscillation or schedule
SWITCH
ON/OFF
Press Switch to turn heater on and off remotely
Set Target Temperature by using + or - buttons
MODES
Press Mode for options, one mode can be
selected at any one time. Press selected mode
once to activate.
COOL
Press Mode. Press Cool to activate the cool
mode.
Set Target Temperature by using + or - buttons

LOW HEAT
Press Mode. Press Low Heat to activate.
Set Target Temperature by using + or - buttons
HIGH HEAT
Press Mode. Press High Heat to activate.
Set Target Temperature by using + or - buttons
TIMER
Using the Timer function, the heater can be set
to turn off after a specified amount of time.
Choose Timer at the bottom of the main screen,
select the duration of time that you want the
heating to stay on for. The heater will turn off
after the selected amount of time has passed.
Use the cancel button to stop the countdown.

OSCILLATION
Press Settings on the main screen. Slide
oscillation button to right to activate. Slide left to
deactivate.
TOWER FAN LIGHT
Press Settings on the main screen. Press light
to ON. Press required colour to turn on the light
on the top of the fan. To turn off choose the OFF
button.

SETTINGS
SCHEDULE
In settings operate the schedule by
pressing the Schedule > button.
Press Add button.
To add just one occurrence select the
time you want to start the heater, press
Switch and selecton. Press Done
followed by Save
Select the time you want the heater to
turn off, press Switch and select off.
Press Done followedby Save

WEEKLY SCHEDULE
To turn the heater on for specific day(s) and
time(s).
Press repeat to show days of the week.
Tick the day(s) of the week you want the heater
to turn on.
Press < button on top left hand of the screen.
To receive a notification to your phone to alert
when the schedule has activated, before saving
press notification.
Select the time you want the heater to start.
Press Switch.
Press ON followed by Done. Press Save
To turn the heater off, press repeat to show
days of the week.
Tick the same day(s) of the week you want
the heater to turn on.
Press < button on top left hand of the screen.
Select the time you want the heater to turn
off.

Press Switch followed by Off.
Press Done followed by Save.
This screen will list the times and dates you
have selected to turn the heater on and off.
Press <