TDE Instruments Digalox DPM72-MPPV-USB User manual

Digalox® DPM72-MPPV
Instruction manual (Rev-2021-04)
Graphical panel meter with RGB backlight for analogue signal 2 × 0/2 - 10 V
Pac age contents: Panel meter igalox® PM72-MPPV, mounting bracket,
5 jumpers, 2 instruction manuals (EN + E)
1. Safety instructions
•Read instruction manual carefully before operating the device! Keep for later
reference.
•Mounting and installation must be carried out by suitably qualified and competent
persons only.
•When wor ing on the device hazardous voltages must not be connected to
the device! The terminals J1-J12 are not isolated from the measuring
circuit.
•The device must not be used as the only protective device or protective
shutdown.
•The device is not intended to protect persons or facilities against harm. Specific
devices must be used to guarantee safety (protection relays, cut-off switches,
etc.).
•When connecting switches to the terminals J1-J8, only switches must be used
whose isolation voltage is at least twice the maximum occurring measurement
voltage. For example, when measuring 30;V C switches must be isolated for at
least 60;V.
•o not open the housing!
•o not use the device in the presence of explosive or flammable substances!
•All cables carrying hazardous voltages must be secured with external separators.
2. Meaning of symbols
General warning sign
(Attention, observe the documentation!)
Warning of an electrical hazard
----- 1 / 8 -----

3. Intended use
•Measurement of voltage in the specified measuring range for process signals
•Indoor use non condensing, non corrosive.
•Panel mounting.
•In operation, supply the device preferably via screw terminals with 12 to 24;V
AC/ C instead of via USB.
•Failure to comply with these instructions will void all guarantee and warranty.
4. Description
The measurement type analogue signal 0/2 to 10 V C is supported at two
measurement inputs. The multi display with RGB backlight is able to display up to
four parameters simultaneously. Thresholds can be associated with individual
warning colours. The unit can be switched between display values via an external
switch. Minimum and maximum values are recorded and can be displayed and reset
via jumper or an external switch. Measured values are recorded over a timespan of
36 seconds up to 14 days. The timebase as well as the display of the measuring
history can be activated by an external switch. The measured values remain stored
as long as the device is supplied with voltage.
The following parameters can be adjusted using the configuration software “ igalox®
Manager”: scale endpoint, scale caption, display style (pointer, tachometer, bar
graph, and more), splash image, backlight colour, thresholds for alarm output,
threshold warning colour (light, blink), hysteresis, and more. Recorded
measurement values can be read and a continuous transmission of the actual
measuring value can be enabled. Using the software, values can be viewed and
exported as CSV. epending on the model, measured values can be transmitted via
USB, XBEE radio technology or RS485 Modbus interface. In addition, the devices
feature a counting function with data retention.;This enables operating-hours-
counters or time-counters for exceeding and falling below threshold values, as well
as double pulse counting.
Visit www.digalox.com to download the software “ igalox® Manager”.
----- 2 / 8 -----

5. Product overview
3
5
4
2
1
2
6
Front
1 Unit or free text
2 Threshold values
3 Upper scale caption
4 Graphical measurement display
5 igital measurement value
6 Lower scale caption
Digalox DPM72-MPPV
www.digalox.com
Made in Germany
USB
Output max.
30 V
50 mA
–
Supply
12 - 24 V
~/
+
Mode 1 Mode 2 Mode 3
Autocale
Min/Max
Timebae
Bu 1 Bu 2 NC GPIO 1 GPIO 2 NC
J1 J2 J3 J4 J5 J6 J7 J8 J9 J12 J11 J10
U2low U2high U1high U1low
30 V max. 30 V max.
3
2
1
4
5
Bac
1 2 optocoupler switch outputs
2 Jumper pins J1–J12
for activating/switching of graphical
historic data display, min/max
display, auto-scaling, display value
(mode), ...
3 Supply voltage input
4 Interface
(USB Micro-B / XBEE / RS485)
5 Measurement inputs
6. Mounting
Carefully insert the device into the panel
cut-out. Insert the mounting bracket from
the back and push towards the panel until
the device sits tight. Make sure the
mounting bracket is snapped into the side
of the housing. To ensure IP65 protection
(dust and water jet) when mounting in a
front panel, use optional gasket
(separately available).
----- 3 / 8 -----
Panel thickness: max. 6 mm
Press mounting
bracket

7. Electrical connections
Supply (Digalox)
Digalox
−+
12 - 24 V Fuse 250 mA
Supply
Legend
Voltage source, e.g. active sensor
or sensor with voltage supply
10 V analogue signal
Sensor
Digalox
U2low U2high
max.
30 V
U1high U1low
- +
0 V 10 V
+
-
Supply (sensor)
2 × 10 V analogue signal
Sensor
Digalox
U2low U2high
max.
30 V
U1high U1low
max.
30 V
- +
0 V 10 V
+
-
Supply (sensor)
Sensor
+
-
Supply (sensor)
- +
0 V 10 V
WARNING: The device may only be operated in one of the connection
options shown above!
----- 4 / 8 -----

8. Configuration
Connect the device to a computer:
USB: Connect the device and the computer using a USB cable. The
device driver is installed automatically if the computer is connected to
the Internet.
XBEE: Insert the XBEE stick into the computer. The device driver is
installed automatically if the computer is connected to the Internet. In
order to reset the XBEE settings, short-circuit terminal J8.
RS485: Short-circuit terminal J8. isconnect the device from the
Modbus network and connect it to the computer using an RS485 USB
adapter. After completing the configuration, open J8 again.
Start the " igalox® Manager" software and connect it to the device. Settings can
then be made on the various tabs and saved in the device.
Please note that the display value selected in “ igalox® Manager” is displayed only
until the power supply of the PM72 is interrupted.
In further operation, the device always shows the first display
value or the one that is selected by the jumpers
J4-J6 (see table “display value”),
in case of a multi display style additionally the following display values.
Table display value (factory preset, can be changed by software)
display value Measurement
input
Display display value
selection
1 10 V (U1) C scaled U1 10 V
%
J1 J12
2 10 V (U2) C scaled U2 10 V
%
J1 J12
3 2-10 V (U1) C scaled U1 2-10 V
%
J1 J12
4 2-10 V (U2) C scaled U2 2-10 V
%
J1 J12
----- 5 / 8 -----

9. Other settings
The following functions can be activated independently during operation by short-
circuiting connectors J1-J3, e.g. using a jumper or switch:
J1: Graphical historic data display
The unit displays the stored values within
the set time base as a graphical trend. The
time base can be set to days (7, 14),
hours (1, 3, 6, 12, 24, 48, 72), minutes (3,
15, 30) or seconds (36).
The time base can be changed by
alternately opening and closing J1 (interval
< 2 sec). When first opening and closing J1
the current time base is displayed. For each
subsequent opening and closing the time
base changes to the next setting. In order to
save the setting permanently, the software
“ igalox® Manager” has to be used.
J2: Min-Max display
The display shows the maximum and
minimum values recorded since the last
reset. The values can be reset by opening
and closing connection J2 shortly (interval <
2 sec). The display shows “Minmax reset”.
J3: Auto-scaling
The device automatically changes the upper
scale caption depending on the current
measuring value between 10, 100 and the
set upper scale caption.
----- 6 / 8 -----

10. Maintenance
Periodically check all external cable connections.
11. Cleaning
Observe the safety instructions before cleaning the device. Clean the device with a
dry lint-free soft cloth. o not use solvents.
12. Specification
DPM72-MPPV
Supply 12 - 24 V AC/ C ±10% (50/60 Hz ±10%) or if
applicable via USB, galvanically isolated
Power consumption Max. 2.4 W
isplay LC graphic display 192 × 160 pixels,
16 grey levels with RGB backlight
Measuring range voltage ±30 V C, 20 V AC, 10 - 500 Hz
Accuracy voltage ±0.5 % true RMS
Internal resistance voltage 102 kΩ
Measuring value update 5 Hz (32 kHz sampling rate)
Recording of measurement 36 seconds to 14 days,
180 internal memory locations
Alarm outputs 2 optocoupler outputs max. 30 V C, 50 mA
Permissible voltage between
supply and measuring inputs < 50 V AC, < 75 V C
Connections
(measuring inputs)
- Wire gauge
- Wire strip length
- Pitch
0.2 - 3.3 mm² (24 to 12 AWG)
7 - 8 mm
7.62 mm
Connections (supply, alarm
outputs and RS485)
- Wire gauge
- Wire strip length
- Pitch
0.13 - 1.3 mm² (26 to 16 AWG)
6 - 7 mm
3.5 mm
Operating temperature 0 °C to +50 °C
Storage temperature -20 °C to +70 °C
Operating altitude 0 to 2000 m above sea level
IP code IP65 (front), IP00 (back)
imensions 72 mm × 72 mm × 58 mm
Panel cut-out 68 mm × 68 mm
epth 55.3 mm (with plugs, cable direction rear facing)
72.6 mm (with antenna)
Net weight 148 g
----- 7 / 8 -----

13. Dimensions [mm]
14. Available accessories
T E Instruments igalox® PM72 gasket EP M/SBR
15. Contact information
T E Instruments GmbH, Gewerbestraße 8, -71144 Steinenbronn
Phone: [phone]
E-mail: [email protected]
Internet: www.tde-instruments.de, www.digalox.com
----- 8 / 8 -----
56.3
83.5
72.0
72.0
77.5
18.627.0
9.6
2.9
73.5
72.0
55.3
63.0
72.0
2.9
35.9
67.5
83.5
Panel cut-out
68.0
68.0
86.9
58.2
36.7