TDS Fitness Equipment C8275 User manual

FRONT CROSS BEAM
(WITH PULLEY BRACKET)
REAR CROSS BEAM
BASE
SEAT MOUNT
SEAT CARRIAGE
KNEE CATCH
PULLEY
FRONT UPRIGHT
(WITH 2 - 1” HOLES)
LAT BAR
UPPER CABLE
WITH STOPPER
TOP CROSS FRAME
(PRE ASSEMBLED WITH
TWO PULLEYS)
LOWER CABLE
ROWING
ATTACHMENT
C8275 - ASSEMBLY INSTRUCTIONS
OUTSIDE CAP
OUTSIDE CAP
OUTSIDE CAP
REAR UPRIGHT
Page 1 of 5 101014

FRONT CROSS BEAM
(WITH PULLEY BRACKET)
REAR CROSS BEAM
BASE
SEAT MOUNT
CARRIAGE
CARRIAGE
KNEE CATCH
PULLEY
OUTSIDE CAP
OUTSIDE CAP
OUTSIDE CAP
4 X 8” FOAM PAD - 2 PCS
4 X 8” FOAM PAD
UPPER CABLE
ROUND PLUG
Page 2 of 5

C8275 - PARTS LIST
BASE
REAR CROSS BEAM
FRONT CROSS BEAM
CARRIAGE
LAT BAR
SEAT MOUNT
ROW HANDLE
TOP CROSS FRAME
(PRE ASSEMBLED)
FRONT UPRIGHT
(WITH TWO HOLES)
REAR UPRIGHT
UPPER CABLE
WITH (2) SNAP HOOKS)
100” LONG
LOWER CABLE
WITH (1) SNAP HOOK)
84” LONG
PREASSEMBLED
3.5” PULLEY
(2) 4 X 8 FOAM
PADS
1” X 18” TUBE
(2) END CAPS
FOR 1” TUBE
SEAT - 9.5” X 12”
OUTSIDE CAPS (4)
Page 3 of 5

THIS UNIT IS BULKY, HENCE REQUIRES TWO PEOPLE TO ASSEMBLE.
THIS UNIT REQUIRES (1) 9/16 WRENCH AND (1) 11/16” WRENCH FOR ASSEMBLY. DO NOT TIGHTEN
HARDWARE UNTIL INSTRUCTED.
STEP 1: PUSH (4) 2 X 2 OUTSIDE CAPS ONTO BASE. ATTACH FRONT AND REAR BEAMS TO THE
BASE WITH (4) 3/8” X 3” HEX BOLTS, (8) 3/8” FLAT WASHERS AND (4) 3/8” LOCK NUTS
STEP 2: ATTACH FRONT & REAR UPRIGHTS TO THE BASE WITH (4) 3/8” X 3” HEX BOLTS, (8) 3/8”
FLAT WASHERS AND (4) 3/8” LOCK NUTS.
CAUTION: THE BASE HAS (6) HOLES. THE TWO HOLES CLOSE TO AN END MUST BE ATTACHED TO
THE REAR CROSS BEAM.
STEP 3: ATTACH SEAT MOUNT TO THE FRONT UPRIGHT AND BASE WITH (4) 3/8” X 3” HEX BOLTS,
(8) 3/8” FLAT WASHERS AND (4) 3/8” LOCK NUTS
STEP 4: INSTALL CARRIAGE BY INSERTING FROM THE TOP OF THE REAR UPRIGHT. MAKE SURE
THE PLATE HOLDER IS FACING FRONT
STEP 5: PLACE THE PRE-ASSEMBLED TOP FRAME ONTO TWO UPRIGHTS, (CABLE STOPPER BUSH
ASSEMBLY MUST FACE UPWARDS SO THAT THE CABLE WILL MOVE BETWEEN FRONT PULLEY AND
THE CABLE STOPPER) ALIGN THE HOLES AND ATTACH WITH (2) 3/8” X 3” HEX BOLTS, (4) 3/8” FLAT
WASHERS AND (2) 3/8” LOCK NUTS (DETAILED INSTRUCTIONS GIVEN IN NEXT PAGE)
STEP 6: PLACE 3.5” PULLEY INSIDE THE BRACKET OF FRONT CROSS BEAM AND ASSEMBLE WITH
(1) 3/8” X 2 ½”HEX BOLT WITH (2) 3/8” FLAT WASHERS AND (1) 3/8” LOCK NUT.
STEP 7: ATTACH SEAT TO THE SEAT MOUNT BY USING (2) 3/8” X 1 1/4” HEX BOLTS WITH (2) 3/8”
FLAT WASHERS.
STEP 8: ATTACH THE UPPER CABLE TO THE CARRIAGE THROUGH TOP TWO PULLEYS AS SHOWN.
STEP 9: ATTACH KNEE CATCH TO THE FRONT UPRIGHT WITH 18” LONG 1” TUBE, (2) 4 X 8 ROUND
FOAM PADS AND (2) END CAPS.
STEP 10: CHECK THE UNIT ON A LEVEL SURFACE BEFORE TIGHTENING ALL BOLTS AND NUTS.
MAKE SURE THE PULLEYS ROTATE FREELY WITHOUT ANY RESISTANCE DUE TO THE OVER
TIGHTNESS.
HARDWARE LIST:
2 - 3/8” X 1 1/4” HEX BOLTS (FOR SEAT)
17 - 3/8” X 3” HEX BOLTS
1 - 3/8” X 2 ½” HEX BOLT ( FOR FRONT LOWER PULLEY)
18 - 3/8” LOCK NUTS
38 - 3/8” FLAT WASHERS
4 - OUTSIDE CAPS
1 - SEAT
2 - 1” END CAPS
2 - 4 X 8 FOAM PADS
3 - 3 ½”PULLEYS (TWO ASSEMBLED)
ASSEMBLY INSTRUCTIONS FOR C-8275 LAT/ROW MACHINE
Page 4 of 5

INSTALLING UPPER CABLE:
INSTALL TOP CABLE BY THREADING THE
END WITHOUT STOP, UP OVER THE FRONT
TOP PULLEY (BETWEEN PULLEY AND
CABLE STOPPER ASSEMBLY) THEN OVER
THE REAR TOP PULLEY AND DOWN TO THE
WEIGHT CARRIAGE. CONNECT CABLE TO
WEIGHT CARRIAGE USING CARBINE HOOK
.
Page 5 of 5 100814
INSTALLING LOWER CABLE:
TO INSTALL LOW ROW CABLE YOU
MUST FIRST REMOVE THE LOW PULLEY,
INSERT THE CABLE THEN REINSTALL
PULLEY. THEN CONNECT WITH THE TOP
CABLE USING A CARBINE HOOK.
CABLE STOPPER ASSEMBLY
TDS Fitness Equipment
160 Home street
Elmira, NY 14904
1-800-446-1833
Fax: [phone]