TE Connectivity AMS600 User manual

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
1 of 17
Rev [1]
5 October 2021
AMS600 PLOTTER OPERATING
INSTRUCTIONS
THIS IS A CLASS 1 DOCUMENT WHICH IS NONCONFIDENTIAL.
The information contained within this document is the property of TE Connectivity. It is supplied in confidence and the
commercial security of the contents must be maintained. It must not be used for any purpose other than that for
which it is supplied nor may any information contained in it be disclosed to unauthorised persons. It must not be
reproduced in whole or in part without obtaining written permission from TE Connectivity (TE).
While TE has made every reasonable effort to ensure the accuracy of the information in this catalog, TE does not guarantee that it is error-free, nor does TE make any other representation,
warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice.
TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose.
The dimensions in this catalog are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions
and design specifications.
*Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
2 of 17
Rev [1]
5 October 2021
Table of Contents
1. INTRODUCTION...........................................................................................................................3
2. ITEMS SUPPLIED .......................................................................................................................4
3. PRODUCT OVERVIEW.............................................................................................................5
4. SETING UP THE AMS600 PLOTTER ............................................................................... 6
5. OPERATION...................................................................................................................................7
6. CLEANING AND PRODUCT CARE................................................................................ 11
7. ACCESSORIES ......................................................................................................................... 12
8. TROUBLE SHOOTING .......................................................................................................... 13
9. TECHNICAL INFORMATION.............................................................................................. 14
10. INSTRUCTIONS FOR PACKAGING THE AMS600............................................ 15
11. SAFETY INSTRUCTIONS................................................................................................ 16

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
3 of 17
Rev [1]
5 October 2021
1. INTRODUCTION
Thank you for purchasing the AMS600, a flexible plotter that helps you label marking elements
quickly and easily.
Rugged construction in stylish aluminum
Labelling area 422 mm x 305 mm
Easy to change fixtures to suit a variety of marking elements
Automatic fixture recognition largely avoids the need to select marking elements
Optimum plotter pen seal. Pens can be stored in the plotter's pen station
during operation
Auto calibration no adjustment necessary
Capable of labelling marking elements up to 10.5 mm
in height. Special solutions for up to 15 mm are
possible
Universal power supply of 100-240V AC / 50-60Hz, various adaptors available
The special start-up function for the plotter pens ensures neat labelling
right from the very first marking element
PC interface: USB port
Control language: HPGL
I/O interface for connecting peripheral equipment, such as engraving option
Possible to update AMS600 firmware through PC connection and
downloading from the Internet

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
4 of 17
Rev [1]
5 October 2021
2. ITEMS SUPPLIED
Please check you have received all the items supplied with your labelling device
(see list below).
Please retain the packaging in case you need to return the device.
The following items are supplied as standard:
1. Plotter AMS600
2. AMS Software CD
3. AMS Power supply cable
4. AMS USB cable
5. Support plate SPRC-1
1.
2. 3. 4. 5.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
5 of 17
Rev [1]
5 October 2021
3. PRODUCT OVERVIEW
1) Plotting area
2) Pin stops for fixtures
3) Fixture recognition sensors
4) Pen station
5) Start-up writing area, priming plates
6) Sealed storage holders in pen station
7) Clip adaptor for holding the plotter pen
8) Pen holder
9) USB port
10) Interface for optional external devices
11) Power supply connection
12) Control panel/control keys
13) Plotter arm
14) Plug for positioning stud for zero setting engraving tool

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
6 of 17
Rev [1]
5 October 2021
4. SETTING UP THE AMS600 PLOTTER
LOCATION
A dry, dust-free room is the ideal environment for the plotter. If possible, do not install the
device in damp or very dusty areas. Do not expose the system to direct sunlight. Please
ensure that the connections on the back right-hand side of the device are accessible at all
times. Position the AMS600 firmly on the work surface where it is to be used, ensuring it is
level.
Please ensure that the writing arm can move freely and is not obstructed by other objects.
CONNECTIONS
Plug the device into a correctly installed mains socket using the power supply included with the
product.
The power supply features a variable AC input voltage of 100-240V AC / 50-60Hz. The
power connection can be replaced by way of adapter plugs.
Plug the connector from the output cable on the power supply into the back right-hand side of
the plotter.
Then hook up the device using the USB cable provided. The respective port is located on the
back right-hand side of the AMS600.
Please note: Please follow the instructions of installing the device
driver accordingly.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
7 of 17
Rev [1]
5 October 2021
5. OPERATION
Once you have installed the AMS600 and connected the power supply and data
cable, you can switch the plotter on.
Important:
Before switching the device on please ensure that there are no objects on the
writing/plotting area which might prevent the writing arm from moving freely. All
settings and commands are entered using the control panel.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
8 of 17
Rev [1]
5 October 2021
ON/OFF buttons
The ON/OFF buttons are used to activate and deactivate the device. When the plotter is
switched on, the writing arm moves to the top right-hand corner of the labelling area and
auto calibration takes place. The green light comes on when the system is ready for use
and to receive data from the PC.
Clear buffer
If the AMS600 contains data, the yellow light will come on. You can delete this data by
pressing the Clear buffer key.
To do this the system must be in stop mode (red light on).
Open/close pen station
Before using the AMS600, insert the plotter pen with the desired tip width into the pen
station.
Important:
Only plotter pens of the types shown here may be used as
the sealing system is designed specifically for these plotter
pens. Using other plotter pens and writing instruments may
damage the device.
To insert plotter pens into the pen station, press the
Pen station open/close key. This is only possible when the system is in stop mode.
When the pen station has been opened, you can insert the plotter pens into the
corresponding storage holders and then re-close the pen station by pressing the
open/close key again.
Please note:
The pen station will close automatically after 2 minutes or power off as there is a danger
the pens will dry out. You can leave plotter pens for the daily work in the pen station
because the optimised seal largely prevents pens from drying out. If the storage inserts
become soiled over time you can replace them. The procedure for changing the storage
inserts can be found in the accessories section.
Please note:
Should you wish to use other plotter pens with HP fixing system, you must insert them
directly into the clip adaptor of the pen holder and ensure that they are not stored in the
pen station.
Please note:
The plotter always re-calibrates prior to first plotting.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
9 of 17
Rev [1]
5 October 2021
Please note:
In the engraving mode the key is used to move the tool to the position of the
indication for standardizing the engraving needle, zero setting.
Stop-key
If the stop-key is activated while the plotter is in action, the job will pause immediately,
the plotter pen brought back to the pen station and the plotter will move into the top
right-hand corner. The red light will signal the interruption. Pressing the key again the
plotter will continue with the job. The red light will go out.
Cursor keys & Pen up/down keys
These keys can be used to move the writing arm manually in all directions. The pen
up/down key lowers and raises the plotter pen. The system must be in stop mode.
Please note:
These key functions are not used for normal operation. They are intended solely for
adjusting settings and carrying out servicing.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
10 of 17
Rev [1]
5 October 2021
Placing the support plates(fi xtures) on the Plotter
There are eight pin stops on the plotting area where up to four different support plates
can be loaded. Different support plates are available depending on the size of the
marking elements. They can occupy one, two or four segments on the plotting area.
Different sized support plates (fixtures):
1 segment 2 segments 4 segments
Placing the elements in the support plates
Choose the appropriate support plates for the elements to be labelled and insert the
elements carefully into the support plate. You can also add the elements first and then
place the support plate on the plotter.
Please note: The plotter always re-calibrates prior to first plotting.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
11 of 17
Rev [1]
5 October 2021
6. CLEANING AND PRODUCT CARE
Protect the AMS600 from dust and other dirt. When not in use, cover the plotter. A
special cover is available as an accessory.
Wipe the device occasionally after use with a dry, lint-free cloth or a mild cleaning
agent.
If the pen station storage inserts and priming plates are heavily soiled, please replace
them.
The description for the sealed unit can be found in the section on accessories.
Important:
Under no circumstances use harsh cleaning products to clean the plotter.
Never lubricate the mechanical parts of the plotter.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
12 of 17
Rev [1]
5 October 2021
7. ACCESSORIES

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
13 of 17
Rev [1]
5 October 2021
8. TROUBLE SHOOTING
If your AMS600 plotter is not functioning correctly, please check the following:
Functional error
Potential solution
Device fails to switch on
Check whether the mains plug and connecting
plug are plugged in and switched correctly.
Check whether the socket being used is
functioning properly. Is the green light on the
power supply illuminated? If not, please replace
the power supply.
Plotter does not respond to data
downloaded from PC
Is the interface cable connected properly? Replace
the data cable if necessary.
Is the device driver installed properly?
No labelling is taking place even though a
plotter pen has been inserted.
Check whether the plotter pen has dried out
or if there is sufficient ink in the pen.
Refill or replace the pen if necessary.
Poor labelling quality, uneven line
thickness, missing items
The plotter pen tip may be soiled. Clean the
tip carefully using a lint-free cloth dipped in
special cleaning fluid.
Replace the plotter pen if
necessary.

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
14 of 17
Rev [1]
5 October 2021
9. TECHNICAL INFORMATION
AMS600 plotter specifications
Type of plotter: Flatbed plotter
Maximum plotting area: 422 mm x 305 mm
Plotting speed with pen: up to 40 mm/s
Plotter pen: Special plotter pens with HP fixing
Ports: USB Level 2.0
Control language: Based on HP-GL 7475A 16 MB
Buffer: 16 MB
Drive: Two-phase step motor
Pen station: Max. 4 plotter pens with double seal
Addressable resolution: 0.01 mm
Repeat accuracy: 0.05 mm
Repeat accuracy after pen change: 0.05 mm with optimum pen
Power supply: Via separate power supply with
exchangeable mains power
connection
Power supply input voltage: 100-240V AC / 50-60Hz
Power supply input current: 0.7 A max. Power supply output
Power supply output voltage: 24 V DC
Power supply output current: 1.25 A max.
Environmental conditions: In use: 10°C-35°C
35%-75% relative humidity
Storage: -10°C-50°C
10%-90% relative humidity
Safety certificate: EN 60950-1
Interference safety compliance: EN 55022 B
EN 61000-4-2, -4-3, -4-4, -4-5, -4-6
Dimensions: 690 mm x 480 mm x 155 mm
Weight: 8.3 kg

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
15 of 17
Rev [1]
5 October 2021
10. INSTRUCTIONS FOR PACKAGING THE AMS600
Two corner pieces
Two corner pieces
Inside the box
Accessory box
Center piece covering
the Y-arm

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
16 of 17
Rev [1]
5 October 2021
11. SAFETY INSTRUCTIONS
Safety instructions
●Keep the operating instructions in a safe place.
●This device complies with all recognised technical standards and all relevant safety
regulations.
●The mains power supply used must correspond with that specified on the name plate.
●Use in dry conditions only.
●Disconnect the device from the mains socket by pulling the plug, not the cord.
●All repairs, including replacement of mains power supply components, must be
performed by a qualified service technician.
Säkerhetsföreskrifte
●Förvara bruksanvisningen på säker plats.
●Denna apparat är tillverkad enligt modern teknik och i enlighet med gällande
säkerhetsföreskrifter för elektriska apparater.
●Kontrollera uppgifterna på typmärket innan anslutning till eluttag.
●Apparaten får endast användas i torra utrymmen.
●Dra inte ur kontakten ur eluttaget genom att rycka i sladden.
●Reparationer av denna apparat, inklusive utbyte av el-sladd, får endast utföras av
fackman.
Sicherheitshinweise
●Bewahren Sie die Gebrauchsanweisung sorgfältig auf.
●Dieses Gerät entspricht den anerkannten Regeln der Technik und den einschlägigen
●Sicherheitsbestimmungen für Gerätesicherheit.
●Elektrische Anschlussbedingungen und Angaben auf dem Typenschild müssen
übereinstimmen
●Gerätenutzung nur in trockenen Räumen
●Netzstecker nicht am Kabel aus der Steckdose ziehen
●Reparaturen an diesem Gerät, einschließlich der Austausch der Netzzuleitung,
dürfen nur von Fachkräften durchgeführt werden

5375 (08/13)
411-121099
INSTRUCTION
CLASS 1- Public
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
| Indicates Change
TE Proprietary & Confidential Information
Class I Data Classification - See Policy TEC-02-04
17 of 17
Rev [1]
5 October 2021
Instructions de sécurité
●Conserver ces instructions dans un endroit sûr.
●Cet appareil répond aux normes techniques et satisfait toutes les règles de sécurité.
●Le courant utilisé doit être identique à celui spécifié sur l'appareil.
●Ne pas utiliser cet appareil dans un environnement humide.
●Débrancher l'appareil en tirant sur la prise, pas sur le câble.
●Toutes les réparations y compris le remplacement des composants électriques, doivent être
effectuées par un technicien qualifié.
Instrucciones de Seguridad
●Conserve las instrucciones de seguridad en un lugar seguro.
●Este equipo cumple con todas las normas técnicas de seguridad eléctrica y
requisitos de seguridad eléctrico aplicables en el país de uso.
●La fuente de alimentación debe corresponderse con los valores de tensión y
corriente citados en la placa de identificación del producto.
●Las características de la fuente de alimentación a utilizar con el producto son las
siguientes : entrada : 100-240Vca, 50/60Hz, 700mA. Salida : 24Vcc/1,25A
●Utilice el equipo en condiciones secas únicamente.
●Desconecte el equipo de la red de alimentación por medio de la ficha, nunca tirando del
cordón.
●Todas las reparaciones, incluyendo el reemplazo del cordón de alimentación, deben
ser realizadas por personal técnico calificado.