Teac DS-H01 User manual

Z
ENGLISH
FRANÇAIS
ESPAÑOL
DS-H01
DIGITAL DOCKING STATION
MANUAL DEL USUARIO
Qué hay en la caja .................33
Antes de su utilización.............33
Conexiones .......................34
Nombres y funciones de las partes
(conexión de base Dock) . . . . . . . . . . 36
Utilización de un iPod/iPhone/iPad
conlabaseDock..................37
Utilización del mando a distancia. . 38
Nombres y funciones de las partes
(mando a distancia) . . . . . . . . . . . . . . . 39
Funcionamiento básico. . . . . . . . . . . . 40
Solución de posibles fallos . . . . . . . . 44
Especificaciones...................45
MODE D’EMPLOI
Contenu de l'emballage ...........19
Avant l’utilisation ..................19
Branchements.....................20
Nom et fonctions des parties
(station d'accueil)..................22
Emploi d'un iPod/iPhone/iPad
avec le dock .......................23
Emploi de la télécommande.......24
Nom et fonctions des parties
(télécommande) ..................25
Fonctionnement de base. . . . . . . . . . 26
Guide de dépannage..............30
Caractéristiques techniques .......31
OWNER’S MANUAL
What’s in the Box ...................5
Before use..........................5
Connections .......................6
Names and Functions of Parts
(Docking Station)...................8
Using an iPod/iPhone/iPad with the
Dock ...............................9
Using the remote control..........10
Names and Functions of Parts
(Remote Control) ..................11
BasicOperation...................12
Troubleshooting. . . . . . . . . . . . . . . . . . . 16
Specifications .....................17
3D0806920B

2
<Do not expose this apparatus to drips or splashes.
<Do not place any objects lled with liquids, such
as vases, on the apparatus.
<Do not install this apparatus in a confined space
such as a book case or similar unit.
<The apparatus draws nominal non-
operating power from the AC outlet
with its POWER or STANDBY/ON
switch not in the ON position.
<The apparatus should be located
close enough to the AC outlet so that you can
easily grasp the power cord plug at any time.
<The appliance coupler is used as the disconnect
device, the disconnect device shall remain readily
operable.
<If the product uses batteries (including a battery
pack or installed batteries), they should not be
exposed to sunshine, re or excessive heat.
<Caution should be taken when using earphones or
headphones with the product because excessive
sound pressure (volume) from earphones or
headphones can cause hearing loss.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
IMPORTANT SAFETY
INSTRUCTIONS

3
CAUTION
<DO NOT REMOVE THE EXTERNAL CASES OR
CABINETS TO EXPOSE THE ELECTRONICS. NO USER
SERVICEABLE PARTS ARE WITHIN.
<IF YOU ARE EXPERIENCING PROBLEMS WITH
THIS PRODUCT, CONTACT TEAC FOR A SERVICE
REFERRAL. DO NOT USE THE PRODUCT UNTIL IT
HAS BEEN REPAIRED.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the equipment and/or the
receiving antenna.
• Increase the separation between the equipment and
receiver.
• Conn ec t the equ ipme nt into an ou t let on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ T V
technician for help.
CAUTION
Changes or modifications to this equipments not
expressly approved by TEAC CORPORATION for
compliance will void the user’s warranty.
iPad, iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in the
U.S. and other countries.
“Made for iPod,”“Made for iPhone,” and “Made for iPad”
mean that an electronic accessory has been designed
to connect specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the developer
to meet Apple performance standards. Apple is not
responsible for the operation of this device or its
compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod,
iPhone, or iPad may affect wireless performance.
Other company names and product names in this
document are the trademarks or registered
trademarks of their respective owners.
For U.S.A.

4
For European Customers
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed of separately from the municipal
waste stream via collection facilities designated by the government or local authorities.
(b) By disposing of electrical and electronic equipment correctly, you will help save valuable
resources and prevent any potential negative effects on human health and the environment.
(c) Improper disposal of waste electrical and electronic equipment can have serious effects on
the environment and human health because of the presence of hazardous substances in the
equipment.
(d) The Waste Electrical and Electronic Equipment (WEEE) symbol, which shows a
wheeled bin that has been crossed out, indicates that electrical and electronic
equipment must be collected and disposed of separately from household waste.
(e) Return and collection systems are available to end users. For more detailed
information about the disposal of old electrical and electronic equipment, please
contact your city office, waste disposal service or the shop where you purchased the
equipment.
Disposal of batteries and/or accumulators
(a) Waste batteries and/or accumulators should be disposed of separately from the municipal
waste stream via collection facilities designated by the government or local authorities.
(b) By disposing of waste batteries and/or accumulators correctly, you will help save valuable
resources and prevent any potential negative effects on human health and the environment.
(c) Improper disposal of waste batteries and/or accumulators can have serious effects on the
environment and human health because of the presence of hazardous substances in them.
(d) The WEEE symbol, which shows a wheeled bin that has been crossed out, indicates
that batteries and/or accumulators must be collected and disposed of separately
from household waste.
If a battery or accumulator contains more than the specified values of lead (Pb),
mercury (Hg), and/or cadmium (Cd) as defined in the Battery Directive (2006/66/EC),
then the chemical symbols for those elements will be indicated beneath the WEEE symbol.
(e) Return and collection systems are available to end users. For more detailed information
about the disposal of waste batteries and/or accumulators, please contact your city office,
waste disposal service or the shop where you purchased them.
Pb, Hg, C d

5
What’s in the Box
Should any of the following accessories be missing or damaged, please contact the retailer where
you purchased the unit or our audiovisual customer support (see back cover).
AC adapter (PS-M0630) × 1
AC adapter power cord × 1
RCA audio cable × 1
Remote control (RC-1268) × 1
Dry cell batteries (AAA) × 2
Owner's manual (this document) × 1
Warranty card × 1
Before use
QPrecautions for placement
oAvoid placing the unit in direct sunlight, close to a source of heat or in other similar conditions.
Do not place the unit on top of an amplifier or other equipment that might generate heat that
exceeds the operating temperature range of this unit. Doing so could cause discoloration,
deformation or malfunction. (This unit can be placed on top of a TEAC A-H01 without problem.)
oWhen the unit is turned on, if a TV is turned on nearby lines might appear on its screen
depending on the characteristics of the TV broadcast signal. This is not a malfunction of the unit
nor of the TV. If this occurs, turn the unit off.
Cleaning
Wipe the acrylic part of the top cover with a soft cloth. Clean dirt from panel surfaces by wiping
them with a soft cloth that has been slightly dampened by a diluted neutral cleaning fluid. Do
not use chemical cleaning cloths, thinner or similar substances as they could damage the
surface of the unit.
QFor safety, disconnect the power plug from the outlet before cleaning.

6
Power
outlet
A B
LR
VIDEO IN
TV (display)
S-VIDEO IN
PS-M0630
Included
AC adapter
power cord
D
CE
Computer
USB cable
RCA audio cable
RCA video cable
RCA coaxial digital cable
Optical digital cable
S-video cable
TEAC UD-H01, A-H01,
stereo amplier or
powered speakers
Sound input
(LINE IN, etc.)
DIGITAL IN
(OPTICAL)
DIGITAL IN
(COAXIAL)
UD-H01, A-H01
or other digital
sound input device
UD-H01, A-H01
or other digital
sound input device
After all connections are complete, connect the power cord’s plug to the AC wall socket.
<Read the instructions of each device that you intend to use with this unit.
<To avoid hum and noise, do not bundle the connection cords.
<Be sure to connect each plug securely.
Connections

7
AAnalog sound output jacks (LINE OUT)
These output the two channels of audio from the iPod/iPhone/iPad connected to this unit's
dock as analog signals. Connect the RCA jacks to a stereo amplifier or speakers.
Connect this unit's R jack to the R jack of the device receiving sound input and this unit's L jack
to the L jack of the receiving device.
White (L)
Red (R)
White (L)
Red (R)
BUSB port
Set the rear panel PC SYNC USB switch to ON to use this unit as an iPod Dock, enabling the
synchronization of music files between the connected computer and the iPod/iPhone/iPad.
oConnect using a commercially available cable.
oWhen the PC SYNC USB switch is set to ON, no signals are output from the LINE OUT, VIDEO
OUT or DIGITAL OUT connectors.
CVIDEO OUT connectors (S-VIDEO, VIDEO)
These output the video signal from the iPod/iPhone/iPad connected to this unit's dock. Use
these to connect to the S-VIDEO input or composite video input of a TV or monitor.
oConnect using a commercially available cable.
oWhen outputting the iPod/iPhone/iPad video signal, no video will appear on its display.
oIf the iPod/iPhone/iPad has a TV Out menu, select On or Ask. When set to Ask, a screen will be
shown each time before a video is played back. You can then choose whether or not to have
the device output the video signal.
oTo output video from the iPod/iPhone/iPad via the output jack to a TV or other display, start
playback after connecting the iPod/iPhone/iPad to this unit's dock.
DDIGITAL OUT connectors (OPTICAL, COAXIAL)
These output sound from the iPod/iPhone/iPad connected to this unit's dock. Connect one to a
digital sound input port of another device.
COAXIAL: RCA coaxial digital cable
OPTICAL: Optical digital cable (TOS)
oConnect using a commercially available cable.
EDC input port (DC IN 6V)
After completing all other connections, connect the included AC adapter (PS-M0630) to this
jack. Then, connect the AC adapter power cord to the adapter. Finally, connect the AC adapter
power cord plug to a power outlet.
oWhen not using the unit for some time, disconnect the power cord from the power outlet.
V Use only the included AC adapter (PS-M0630) and AC adapter power cord.

8
Names and Functions of Parts (Docking Station)
A CB D
ASTANDBY/ON
Press this button to turn the unit on and to put it into standby. When the power is on, the ring
around the button (power indicator) lights blue.
oIf nothing is connected to this unit when the power is turned on, it will enter standby mode,
and the power indicator will not light blue. When you connect an iPod/iPhone/iPad to the
dock connector or connect an operating computer to the unit using a USB cable, the power
indicator will light blue.
BRemote control signal receiver
This receives signals from the remote control. When using the remote control, aim the end of the
remote control toward the remote control signal receiver.
CDock connector
Use this to connect an iPod/iPhone/iPad.
DDock cover
When not using an iPod/iPhone/iPad, close this to protect the dock connector.
When using an iPod/iPhone/iPad, open this and use it to hold the iPod/iPhone/iPad.
For details, see "Using an iPod/iPhone/iPad with the Dock" on the next page.
oFold the dock connector toward the dock cover before closing the cover.

9
Using an iPod/iPhone/iPad with the Dock
Compatible iPod/iPhone/iPad models
iPod classic
iPod nano (2nd, 3rd, 4th, and 5th generation)
iPod touch (1st, 2nd, 3rd , and 4th generation)
iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G
iPad 2, iPad
Connecting an iPod/iPhone/iPad
1Open the dock cover.
2Fold the dock connector forward.
3Connect the iPod/iPhone/iPad.
4Lean the iPod/iPhone/iPad against the dock
cover.
iPod/iPhone/iPad software
If the unit or remote control buttons do not work
properly with your iPod/iPhone/iPad, updating its
software might solve the problem.
Download the latest software for your iPod/iPhone/
iPad from the following Apple website.
http://www.apple.com/downloads/
1
3
2
4

10
Using the remote control
The included remote control allows this unit to
be operated from a distance.
Point the remote control unit at the main unit’s
remote sensor from within 16 feet/5 meters of
themain unit.
<Remote control op eration may be
impossible if there are any obstacles
between the unit and the remote control.
<If direct sunlight or strong artificial
illumination shines on the remote sensor,
the remote control might not function. If
that is the case, move this unit to another
location.
<If the remote control unit is operated near
other appliances which generate infrared
rays, or if other remote control devices
using infrared rays are used near the unit, it
may operate incorrectly. And conversely, the
other appliances may operate incorrectly.
Battery Installation
1Remove the battery compartment
cover.
2Insert two “AAA” (R03, UM-4) dry
batteries. Make sure that the batteries
are inserted with their positive “+” and
negative “–” poles positioned correctly.
3Close the cover.
Battery Replacement
If the ef fective range decreases, the
batteries are exhausted. In this case, replace
the batteries with new ones.
For detailed information about collection of
bat ter ies, pleas e conta ct your lo cal
municipality, your waste disposal service or
the point of sale where you purchased the
items.
Precautions concerning batteries
Misuse of batteries could cause them to
rupture or leak leading to fire, injury or
the staining of items nearby. Please read
and observe the following precautions
carefully.
<Be sure to insert the batteries with correct
positive “+” and negative “–” polarities.
<Use batteries of the same type. Never use
different types of batteries together.
<Rechargeable and non-rechargeable
batteries can be used. Refer to the
precautions on their labels.
<When the remote control unit is not to be
used for a long time (more than a month),
remove the batteries from the battery
compartment to prevent them from leaking.
If they leak, wipe away the liquid inside
the battery compartment and replace the
batteries with new ones.
<Do not heat or disassemble batteries and
never dispose of old batteries by throwing
them in a fire.

11
Names and Functions of Parts (Remote Control)
A
B
C
D
E
F
G
H
Using the RC-1268 remote, you can control the iPod/iPhone/iPad connected to this unit's dock.
The RC-1268 remote control can control
both A-H01 and DS-H01 models. (The same
remote control is included with the TEAC
A-H01.)
This manual explains the buttons that can
be used with the DS-H01.
AScroll buttons (j/k)
Use these to scroll through menus.
BPlay/pause button (7/9)
Starts/pauses playback.
CShuffle button (½)
Turns shuffle playback on/off.
DRepeat button (REPEAT ¼)
Changes the repeat playback modes.
ESkip buttons (.//)
Press these buttons to skip to the previous
or next song. Hold down these buttons to
search forward or backward.
FSelection button (SELECT)
Press this button to confirm a selection in a
menu.
GMENU
Return to the previous iPod/iPhone menu.
This is the same as the iPod MENU button.
HVideo output button (VIDEO)
Turns video send on/off.
oYou can send the iPod/iPhone/iPad video
signal from this unit's video output jacks
(VIDEO OUT) to a TV or display. (See page
7 Cand page 14.)

12
Basic Operation
1Press the power button (STANDBY/ON) to turn
the power on.
oIf nothing is connected to this unit when the power
is turned on, it will enter standby mode, and the ring
around the button (power indicator) will not light blue.
When you connect an iPod/iPhone/iPad to the dock
connector or connect an operating computer to the
unit using a USB cable, the power indicator will light
blue.
oWhen connected to an amplifier, always turn
the amplifier’s power on very last to avoid
sudden loud noises.
2After turning the iPod/iPhone/iPad power on,
connect it to the dock.
For details about how to connect an iPod/iPhone/iPad,
see “Using an iPod/iPhone/iPad with the Dock” on
page 9.
oIf you connect an unpowered iPod/iPhone/iPad to the
dock, it might not operate correctly after its power is
turned on.
oThe iPod/iPhone/iPad in this unit's dock will be
charged whenever this unit's power plug is connected
to a power source and its power is turned on.
oWith some iPod/iPhone/iPad models, no sound will be
output from headphones that are plugged into them
when the device is connected to the dock.
oYou can output the iPod/iPhone/iPad video signal
from this unit's video output jacks (VIDEO OUT) to a TV
or display. (See page 7 Cand page 14.)
oWhen outputting iPod/iPhone/iPad video from a
video output jack to a TV or other display, connect the
iPod/iPhone/iPad to this unit's dock before starting
playback.
oWhen using an iOS application on an iPod touch,
iPhone or iPad, start the iOS application before
connecting the device to the dock.
oIf a case being used with an iPod touch, iPhone or iPad
touches this unit's dock when the device is connected,
remove the case and reconnect it.

13
Pausing playback
During playback, press the playback/pause button
(7/9) to pause playback.
When paused, press the playback/pause button
(7/9) to restart playback.
Skipping songs
During playback, press a skip button (.//) to
skip to the previous or next song and start playing it.
Keep pressing the button until the desired song
number is reached.
The selected song will be played from the beginning.
oDuring playback, if the .button is pressed once
the beginning of the current song will be found.
Press it again if you want to play the previous song.
Searching forward and backward
During playback, hold down a skip (.//)
button to search forward or backward. Release it
when you find the part you want to hear.
Repeat playback
Press the repeat button (¼) to cycle through the
iPod/iPhone/iPad repeat modes in the following
order.
Repeat one Repeat all Off
oWhen set to repeat one song, the »icon appears
on the iPod/iPhone/iPad display.
oWhen set to repeat all songs, the ¼icon appears
on the iPod/iPhone/iPad display
Hold down

14
Shuffle playback
Press the Shuffle (½) button to cycle through the
shuff le modes of the iPod/iPhone/iPad in the
following order.
Songs Albums Off
oWhen set to shuffle, the ½icon appears on the
iPod/iPhone/iPad display.
Returning to the previous iPod/iPhone/iPad
menu
Press the MENU button to open the previous iPod/
iPhone/iPad menu.
This has the same function as an iPod MENU button.
Selecting an iPod/iPhone/iPad menu item
Use the scroll buttons (j/k) to select an item and
then press the SELECT button.
Outputting video
When the iPod/iPhone/iPad video selection screen is
open, press the remote control VIDEO button to turn
video output on or off. Since this cannot be confirmed
on the iPod/iPhone/iPad menu screen, start video
playback and check whether video output is on or off
on the TV (display) screen.
oIf the device has a TV Out menu, select On or Ask.
When set to Ask, a screen will be shown each time
before a video is played back. You can then choose
whether or not to have the device output the video
signal.
oSet the TV signal to NTSC or PAL as appropriate for
the region of the TV or other device that you are
using.
Basic Operation (continued)

15
Synchronizing with a computer
This unit can be used as an iPod/iPhone/iPad dock
with recharging capability.
To synchronize an iPod/iPhone/iPad with a computer,
set the rear panel PC SYNC USB switch to ON.
oWhen the PC SYNC USB switch is set to ON, no sig-
nals are output from the LINE OUT or DIGITAL OUT
connectors.
oWhen connected to a computer that does not sup-
port recharging of an iPod/iPhone/iPad, the con-
nected iPod/iPhone/iPad will not be recharged if
the PC SYNC USB switch is set to ON. In this case,
set the PC SYNC USB switch to OFF to recharge the
connected device.
oWhile synchronizing an iPod/iPhone/iPad with a
computer, do not set the PC SYNC USB switch to
OFF. Doing so could cause a device to freeze or
other operation problems.
Operation might differ according to the
iPod/iPhone/iPad model and iOS software
version.
USB cable

16
If you experience a problem with the unit, please refer to the following troubleshooting advice
before seeking repair. If you still have a problem, contact the retailer where you purchased the unit
or TEAC customer service (on the back cover).
The following explanations refer to an iPod, but they also apply to use with an iPhone or iPad.
No power Check that the power cord is properly connected
to the power source. If the source is switched, make
sure that the switch is turned on.
Confirm that power is supplied to the outlet by
plugging in another electric device.
Power indicator
does not light
when power
button pushed
If nothing is connected to this unit when the power
is turned on, it will enter standby mode, and the ring
around the button will not light blue. When you
connect an iPod to the dock connector or connect
an operating computer to the unit using a USB
cable,the ring around the button (power indicator)
will light blue.
iPod not
recognized
Confirm that the iPod model can be used with this
unit. (See page 9.)
If you are using an iPod case, remove it so that the
iPod can dock securely.
iPod music cannot
be played back
If PC SYNC is set to ON, the iPod cannot be used for
playback.
Set the PC SYNC switch to OFF. (See page 15.)
The iPod does not
recharge
When connected to a computer that does not
support recharging of an iPod, the connected iPod
will not be recharged if the PC SYNC USB switch is
set to ON. In this case, set the PC SYNC USB switch to
OFF to recharge the connected device.
No video output Press the VIDEO button on the remote control. (See
page 14.)
If the iPod has a TV Out menu item, set it to On or
Ask.
Noise appears on
TV screen
Check that the iPod TV signal setting is NTSC or PAL
as appropriate. (See page 14.)
General
Since this unit uses a microcontroller, external noise and other interference can
cause the unit to malfunction. If this occurs, unplug the power cord, wait for a
while, then restore power to the unit and try using it again.
Troubleshooting

17
Analog sound output
Connectors ..........................................RCA jacks ×2
Output impedance...................................600 Ω or less
Maximum output level (1 kHz, full-scale, into 10 kΩ load) . . 2.0 Vrms
Frequency response..........................20 Hz–20 kHz (−3 dB)
S/Nratio .....................................................90dB
Total harmonic distortion............................0.05 % (1 kHz)
Digital sound output
Coaxialdigitaljack .............................................×1
Opticaldigitalconnector ......................................×1
Video output
Compositejack ................................................×1
S-Videojack ...................................................×1
USB port
USB Type B .....................................................× 1
General
Power supply
Europe model...................................AC 230 V, 50 Hz
U.S.A./Canada model............................AC 120 V, 60 Hz
Power consumption..........................................18 W
Dimensions (mm) . . . . . . . . . . . . . . . . . . . . . . . . 215 (w) × 70 (h) × 225 (d)
(including protrusions)
Weight .......................................................1.1 kg
Operating temperature.............................+ 5°C to + 35°C
Operating humidity . . . . . . . . . . . . . . . . . . . . .5–85 % (no condensation)
Included accessories
AC adapter (PS-M0630) × 1
AC adapter power cord × 1
RCA audio cable × 1
Remote control (RC-1268) × 1
Batteries (AAA) × 2
Owner's manual (this document) × 1
Warranty card × 1
oSpecifications and appearance are subject to change without
notice.
oIllustrations in this manual might differ in some aspects from the
actual model.
Specifications

18
Pour les consommateurs européens
Mise au rebut des équipements électriques et électroniques
(a) Tout équipement électrique et électronique doit être traité séparément de la collecte
municipale d'ordures ménagères dans des points de collecte désignés par le gouvernement ou
les autorités locales.
(b) En vous débarrassant correctement des équipements électriques et électroniques, vous
contribuerez à la sauvegarde de précieuses ressources et à la prévention de potentiels effets
négatifs sur la santé humaine et l'environnement.
(c) Le traitement incorrect des déchets d'équipements électriques et électroniques peut avoir des
effets graves sur l'environnement et la santé humaine en raison de la présence de substances
dangereuses dans les équipements.
(d) Le symbole de déchets d'équipements électriques et électroniques (DEEE), qui
représente une poubelle à roulettes barrée d'une croix, indique que les équipements
électriques et électroniques doivent être collectés et traités séparément des déchets
ménagers.
(e) Des systèmes de retour et de collecte sont disponibles pour l'utilisateur final. Pour
des informations plus détaillées sur la mise au rebut des vieux équipements électriques et
électroniques, veuillez contacter votre mairie, le service d'ordures ménagères ou le magasin
dans lequel vous avez acquis l'équipement.
Mise au rebut des batteries et/ou accumulateurs
(a) Les batteries et/ou accumulateurs hors d'usage doivent être traités séparément de la collecte
municipale d'ordures ménagères dans des points de collecte désignés par le gouvernement ou
les autorités locales.
(b) En vous débarrassant correctement des batteries et/ou accumulateurs hors d'usage, vous
contribuerez à la sauvegarde de précieuses ressources et à la prévention de potentiels effets
négatifs sur la santé humaine et l'environnement.
(c) Le traitement incorrect des batteries et/ou accumulateurs hors d'usage peut avoir des effets
graves sur l'environnement et la santé humaine car ils contiennent des substances dangereuses.
(d) Le symbole de déchets d'équipements électriques et électroniques (DEEE), qui
représente une poubelle à roulettes barrée d'une croix, indique que les batteries et/ou
accumulateurs doivent être collectés et traités séparément des déchets ménagers.
Si une batterie ou un accumulateur contient plus que les valeurs spécifiées de plomb
(Pb), mercure (Hg) et/ou cadmium (Cd) telles que définies dans la directive sur les
batteries (2006/66/EC), alors les symboles chimiques de ces éléments seront indiqués sous le
symbole DEEE.
(e) Des systèmes de retour et de collecte sont disponibles pour l'utilisateur final. Pour des
informations plus détaillées sur la mise au rebut des batteries et/ou accumulateurs, veuillez
contacter votre mairie, le service d'ordures ménagères ou le magasin dans lequel vous les avez
achetés.
Pb, Hg, C d

19
Contenu de l'emballage
Si un des accessoires suivants manque ou est endommagé, veuillez contacter le revendeur qui vous
a vendu l'unité ou notre service clientèle pour l'audiovisuel (voir au dos de la couverture).
Adaptateur secteur (PS-M0630) × 1
Cordon d’alimentation d'adaptateur secteur × 1
Câble audio RCA × 1
Télécommande (RC-1268) × 1
Piles sèches (AAA) × 2
Mode d’emploi (ce document) × 1
Carte de garantie × 1
Avant l’utilisation
QPrécautions de placement
o Évitez d'exposer l'unité directement au soleil, de la placer près d'une source de chaleur ou dans
d'autres conditions similaires. Ne la placez pas sur un amplificateur ni sur un appareil pouvant
produire une chaleur supérieure à la plage de température de fonctionnement de cette unité. Cela
pourrait causer une décoloration, une déformation ou un mauvais fonctionnement (cette unité peut
sans problème être placée sur un A-H01 TEAC)..
o Quand cette unité est en service, allumer un téléviseur à proximité peut entraîner l’apparition de
lignes sur l’écran de celui-ci, en fonction des caractéristiques de la télédiffusion. Ce n’est pas un
mauvais fonctionnement de l’unité ni du téléviseur. Si cela se produit, éteignez l'unité.
Nettoyage
Essuyez la partie acrylique du dessus avec un chiffon doux. Nettoyez les surfaces avec un chiffon
doux légèrement imprégné d'un détergent liquide neutre dilué. N’utilisez pas de lingettes de
nettoyage imbibées de produits chimiques, diluant ou substances similaires car cela pourrait
endommager la surface de l’unité.
QPar sécurité, débranchez le cordon d'alimentation de la prise avant tout nettoyage.

20
Prise
secteur
A B
LR
VIDEO IN
TV (écran)
S-VIDEO IN
PS-M0630
Cordon
secteur de
l’adaptateur
D
CE
Ordinateur
Câble USB
Câble audio RCA
Câble vidéo RCA
Câble numérique coaxial RCA
Câble numérique optique
Câble S-vidéo
UD-H01, A-H01 TEAC,
amplicateur stéréo ou
enceintes ampliées
Entrée audio
(LINE IN, etc.)
ENTRÉE NUMÉRIQUE
(OPTIQUE)
ENTRÉE NUMÉRIQUE
(COAXIAL)
UD-H01, A-H01
ou autre appareil
à entrée numérique
UD-H01, A-H01
ou autre appareil
à entrée numérique
Une fois tous les branchements faits, raccordez le cordon d'alimentation à une prise secteur.
<Lisez le mode d'emploi de chaque appareil que vous comptez employer avec cette unité.
<Pour éviter tout ronement ou bruit parasite, ne regroupez pas les câbles de connexion.
<Assurez-vous que chaque che est bien enfoncée.
Branchements