Team Play Fun Stop Photos Gen II User manual

Page 1 of 10
© 2014 Team Play, Inc.!
!
!
PRINTER'MEDIA'INSTALLATION'
'
NOTE:''CHANGE'YOUR'PAPER'AND'INK'ROLL'AT'THE'SAME'TIME.''The$media$kit$always$comes$
with$ excess$ paper,$ which$ is$ intended$ to$ be$ thrown$ away$ or$ wasted$ during$ printer$
calibration.$$We$ recommend$ that$ if$ your$ photo$ booth$ says$ “No$ Paper,”$ you$ should$
change$both$the$paper$and$the$ink$ribbon.$$'
'
NOTE:'TORN'INK'RIBBON'DOES'NOT'HAVE'TO'BE'REPLACED.''In$the$unlikely$event$that$an$ink$
ribbon$ tears$ because$ of$ a$ paper$ jam$ (such$ as$ a$ popsicle$ stick$ pushed$ into$ the$ printer$
paper$ outlet),$ the$ ribbon$ does$ not$ have$ to$ be$ replaced.$ $ The$ ink$ ribbon$ can$ be$ taped$
together$and$advanced$past$the$repair.$
'
!
You will find this sticker inside the coin door at the rear of your photo booth:
'
!

Page 2 of 10
© 2014 Team Play, Inc.!
'
'
'
Load'Paper'into'the'Printers'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
$
$
1. Check to be sure that the cabinet is powered ON.
2. Using the keys that are zip-tied to the
curtain rod, unlock and open the
printer access door located at the
back of the photo booth.
3. Remove the printer access door.
4. Press the “Door Open” button on the
front of the printer into which you will
be loading paper.

Page 3 of 10
© 2014 Team Play, Inc.!
5. The printer will unlock the door and
allow the door to be rotated
downward.
6. Remove all shipping material from inside of the printer.
7. Locate the two paper support reels from inside the parts box.
8. Place a support reel into each side of the paper roll.
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$

Page 4 of 10
© 2014 Team Play, Inc.!
$
$
9. Set the roll of paper into the printer.
10. Lock the two support reels into place.
$ $
$
11. Feed the end of the paper strip through
the rollers.
$
$
$
$
$
$
$

Page 5 of 10
© 2014 Team Play, Inc.!
$
$
$
$
$
$
$
$
$
13. After the door is locked into place, the printer
will automatically feed four sheets of paper to
test whether the paper is installed properly.
$
$$$$$$$$$$ $
$
$
$
$
$
$
$
$
$
$
12. Rotate the door
upward, until the
door locks in the
vertical position.
$
$
$
$
$

Page 6 of 10
© 2014 Team Play, Inc.!
14. The cover of the shard tray should be removed.
The shards should fall out of the printer shard
tray to the floor of the printer compartment
inside of the photo booth.
Each time that you replace the paper roll, clean
up the shards from the floor of the printer
compartment.
Use of the shard tray would be likely to cause
the printer to jam and is not recommended.
$
$
$
$
$
$$$$$$$$$$ $
$
$
$
$
$
15. The “READY” light will turn green on the printer
once the ink ribbon and paper have been
loaded properly.
16. Next, load the Ink Film and Ink Tray.
$
$
$
$
$
'

Page 7 of 10
© 2014 Team Play, Inc.!
Load'the'Ink'Film'and'Ink'Tray'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
$
1. Check to be sure that the cabinet is
powered ON.
2. Using the keys that are zip-tied to the
curtain rod, unlock and open the
printer access door located on the
back side of the photo booth.
3. Remove the printer access door.
4. Press the “Door Open” button on the
front of the printer into which you will
be loading the ink ribbon.
$$$$$$$$$$$$$
$
$
$
$

Page 8 of 10
© 2014 Team Play, Inc.!
5. The printer will unlock the door and
allow the door to be rotated
downward. Remove any shipping
materials from inside the printer.
6. The ink film and ribbon support tray
are located inside the parts box that
came with your photo booth.
7. Place the ink film into the support tray,
following the color guides on the tray.
$$$$$$$$$$$$
$
$
$
$
$
$
$

Page 9 of 10
© 2014 Team Play, Inc.!
$
8. The ink film should rotate easily in the
support tray.
9. Slide the ink film support tray into the top
of the printer.
10. The front of the tray should be flush with
the front of the printer if installed correctly.
$
$
$
$
$

Page 10 of 10
© 2014 Team Play, Inc.!
Printer'Power'Button'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
To power up the printers, turn on the photo booth and
press the power button located on the bottom left
corner of each printer.
______________________________________________________________________________$
!
View!and!download!technical!support!manuals!at!www.teamplayinc.com!–!Technical!Support!–!Gen!II.!!!
17. Rotate the door
upward, until the door
locks in the vertical
position.
18. The “READY” light will turn green on the printer
once the ink film and paper have been loaded
properly.