teching Steam Automobile User manual

•
•

34
R

Ｉ－Ｍａｋｅ·ＲｅａｌＭｏｄｅｌ·ＲｅａｌＷｏｒｌｄ

Precautions

目录
1
2
Expiation of the steam Automobile components
P3
Steam Automobile parts list
P52
P03. Boiler components
P08. Cargo bed components
P09. Transmission system
P22. Circuit system
P23. Smoke box components
P35. Front axle components
P40. Steering system
P44. Rear axle components and brake system
P46. Charging status
P47. Function introduction
P48. Mechanical failure analysis and troubleshooting

1
Basic knowledge on standard
parts assembly
(1) Installation of screws
(2)Degree of screw tightening 2.Installation of snap ring
1.Installation of screws
(3)Screw installation order
Correct
orientation
Mount the screws diagonally
in order of number
Push in the
snap ring
in parallel.
Correct
orientation
Skew pushing
of circlip
Wrong
orientation
Wrong
orientation
１ ５ ３
４ ６ ２
Correct position Wrong position
TECHING
R

2
(1)Install the bearing into the bearing seat hole
3.Installation of Bearing
(2）Install the bearing onto the shaft
Correct orientation
Check the orifice of bearing block
for chamfer and burr; apply a little
lubricating oil onto side face of shaft
Installation point; align the bearing
and mount it to the final position;
pressure is applied to the outer race
of bearing.
Check the shaft end for chamfer and
burr; apply a little lubricating oil onto
side face of shaft Installation point;
align the bearing and mount it to the
final position; pressure is applied to
the inner race of bearing.
Wrong orientation
TECHING
R

3
Expiation of the steam car components
1.1 Press the bearing into the bearing seat
1. Boiler components
１
049
118
Two sets in total
1.2 Install the left plate components -1
088
001
125
049
114
110
068
小头朝外
Important note: before assembly, find
the bottled lubricating oil, be sure to
put enough oil in all the places that
need to be lubricated, otherwise the
machine is easy to get stuck
Position indicator
for lubricating oil
TECHING
R

4
1.3 Install the left plate components -2 1.4 Install the water tank
112 115
047
090
126
050
051
001
126
082
056
This toothed
hole is on the
same side as
this big hole
The bosses of
050/051 must be
inserted into the
holes, and the
boss of 047 must
face inwards
TECHING
R
Lubricant(1 positions)
Lubricant(2 positions)

5
1.5 Assemble the boiler components 1.6 Install the motor
127
076
131 060
This hole faces
leftwards
TECHING
R

6
1.7 Assemble the left plate components and the boiler components 1.8 Install the rear cover of smoke pipe
126
128
126
054
Left plate
components
TECHING
R

7
1.9 Install the boiler door
053
111
111
122
043
098
130
The entire plane
faces leftwards
1.10 Install the rear panel
126
128
Boiler door
components
TECHING
R

8
2.1 Fasten the battery 2.2 Install the side panel of the cargo bed
2. Cargo bed components
005
065
077
003 126
126
Pay attention to the
direction of the notch
TECHING
R

9
2.3 Assemble the cargo bed 3.1 Assemble the eccentric wheel components-1
3. Transmission system
126
126
015
012
085
024
Cargo bed
components
Please pay attention to the
directions of the holes.
These two holes are on the
upper and lower sides
respectively.
This end has
toothed hole
Left plate
components
TECHING
R

10
3.2 Assemble the eccentric wheel components-2 3.3 Assemble the eccentric wheel components-3
085
012
015
024
106
046
085
012
015
The hole of 046
must be aligned with
the shaft (024)
Please note that these two
holes are on the left and
right sides respectively
TECHING
R
Lubricant(3 positions)

11
3.4 Assemble the synchronous gear-2 3.5 Install the gear shaft-3
3.6 安装齿轮轴 -5
106
038
041
026
118 032 037
083
040
083
The long flat end faces leftwards
Boss faces outward
TECHING
R
Lubricant(4 positions)
Lubricant(3 positions)