TechNexion TEP-0700-IMX7 User manual

TEP-0700-IMX7 MODULAR HMI PRODUCT MANUAL
(TEP-0700-IMX7)
VER. 1.01
March 11, 2019

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 2of 26
REVISION HISTORY
Revision
Date
Originator
Notes
1.00
July 30, 2018
TechNexion
First public release
1.01
March 11, 2019
TechNexion
Ordering table update

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 3of 26
TABLE OF CONTENTS
1. Introduction ...............................................................................................................................................4
1.1. General Care and Maintenance .........................................................................................................4
2. TEP-0700-IMX7 Product Overview...........................................................................................................5
2.1. Functional Block Diagram ..................................................................................................................5
2.2. Dimensions.........................................................................................................................................6
2.3. Device Cut-out Dimensions For Mounting Though a Panel...............................................................7
2.4. External Connectors...........................................................................................................................8
2.5. Internal Board Connectors ...............................................................................................................11
3. External Connectors................................................................................................................................13
3.1. Serial Port Connector (RS-XXX)......................................................................................................13
3.2. CAN Bus Connector (CANBus)........................................................................................................14
3.3. Digital I/O Connectors (GPIO1/GPIO2)............................................................................................14
3.4. S1 Button..........................................................................................................................................15
3.5. RST Button.......................................................................................................................................15
3.6. LED Light Indicator...........................................................................................................................15
3.7. USB OTG (Type-C) Connector ........................................................................................................16
3.8. MicroSD Card Slot............................................................................................................................16
3.9. Nano-SIM Card Slot .........................................................................................................................16
3.10. Gigabit Ethernet Interface ..............................................................................................................17
3.11. USB Host Connector......................................................................................................................17
3.12. Power Input Connector...................................................................................................................17
3.13. Grounding.......................................................................................................................................18
3.14. Antenna Holes................................................................................................................................18
4. Internal Connectors and Expansion Options ..........................................................................................19
4.1. RTC Battery Connector....................................................................................................................19
4.2. M.2 KEY-B 3G/4G LTE Module Connector......................................................................................20
4.3. SW3 Panel Backlight Switch ............................................................................................................20
4.4. SW2 Panel Scanning Direction Switch.............................................................................................20
5. Mounting..................................................................................................................................................21
5.1. VESA Mounting................................................................................................................................21
5.2. Surface Mounting and O-ring Installation.........................................................................................22
6. Ordering Information ...............................................................................................................................23
6.1. Custom Part Number Rule ...............................................................................................................23
6.2. Standard Package Contents ............................................................................................................24
7. Important Notice......................................................................................................................................25
8. Disclaimer ...............................................................................................................................................26

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 4of 26
1. Introduction
1.1. General Care and Maintenance
Your device is a product of superior design and craftsmanship and should be treated with care.
The following suggestions will help you.
•Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain
minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely.
•Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be
damaged.
•Do not store the device in hot areas. High temperatures can shorten the life of electronic devices,
damage batteries, and warp or melt certain plastics.
•Do not store the device in cold areas. When the device returns to its normal temperature,
moisture can form inside the device and damage electronic circuit boards.
•Do not open the device while power is on.
•Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and
fine mechanics.
•Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
•Do not paint the device. Paint can clog the parts and prevent proper operation.
•Unauthorized modifications or attachments could damage the device and may violate regulations
governing radio devices.
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is
not working properly, take it to the nearest authorized service facility for service.
Regulatory information
Disposal of Waste Equipment by Users in Private Household in the European Union
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose
of your waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
We hereby declare that the product is in compliance with the essential requirements and
other relevant provisions of European Directive 2014/53/EU (Directive on the
harmonisation of the laws of the Member States relating to the making available on the
market of radio equipment and repealing Directive 1999/5/EC).

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 5of 26
2. TEP-0700-IMX7 Product Overview
2.1. Functional Block Diagram

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 6of 26
2.2. Dimensions
The following figure shows the TEP-0700-IMX7 dimensions (unit: mm):

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 7of 26
2.3. Device Cut-out Dimensions For Mounting Though a Panel
The TEP-0700-IMX7 can be mounted on the front or the back of the panel. In order to mount it from the
front, a nominal rectangular cutout must be made in the panel. The following drawing shows the
dimensions of the cut-out area (unit: mm):

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 8of 26
2.4. External Connectors
The TEP-0700-IMX7 has a number of external connectors.
Rear view:
14
16 15 12 13
17 11
10
18 9
8
19 7
1 2 3 4 5 6
External Connectors:
No.
Description
No.
Description
1
RS-XXX (Serial Port) connector
11
USB OTG (Type-C) connector
2
CANBus (CAN Bus) connector
12
MicroSD card slot
3
GPIO1 connector
13
Nano-SIM card slot
4
GPIO2 connector
14
Antenna hole
5
Antenna hole
15
LAN2 RJ45 connector
6
Antenna hole
16
USB Host connector
7
S1 Boot Select button
17
LAN1 RJ45 and PoE (optional)
8
Reset button
18
Power Input connector
9
LED Light indicator
19
Grounding screw
10
Antenna hole

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 9of 26
Bottom view:
5 6
1 2 3 4
Right side view:
10 14
12
7 8 9 11 13
External Connectors:
No.
Description
No.
Description
1
RS-XXX (Serial Port) connector
11
USB OTG (Type-C) connector
2
CANBus (CAN Bus) connector
12
MicroSD card slot
3
GPIO1 connector
13
Nano-SIM card slot
4
GPIO2 connector
14
Antenna hole
5
Antenna hole
15
LAN2 RJ45 connector
6
Antenna hole
16
USB Host connector
7
S1 Boot Select button
17
LAN1 RJ45 and PoE (optional)
8
Reset button
18
Power Input connector
9
LED Light indicator
19
Grounding screw
10
Antenna hole

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 10 of 26
Left side view without side cover:
15 17 18
16 19
External Connectors:
No.
Description
No.
Description
1
RS-XXX (Serial Port) connector
11
USB OTG (Type-C) connector
2
CANBus (CAN Bus) connector
12
MicroSD card slot
3
GPIO1 connector
13
Nano-SIM card slot
4
GPIO2 connector
14
Antenna hole
5
Antenna hole
15
LAN2 RJ45 connector
6
Antenna hole
16
USB Host connector
7
S1 Boot Select button
17
LAN1 RJ45 and PoE (optional)
8
Reset button
18
Power Input connector
9
LED Light indicator
19
Grounding screw
10
Antenna hole

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 11 of 26
2.5. Internal Board Connectors
The TEP-0700-IMX7 has several connectors, switches and internal expansion options. It is necessary to
remove the Power Expansion module to access several switches, headers and connectors.
Rear view (opened device) with the Power Expansion module:
A
Power Expansion Module
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 12 of 26
Rear view (opened device) without the Power Expansion module:
A
E*
B*
C*
D*
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
D*
SW2 Panel switch
B*
M.2 KEY-B 3G/4G LTE module connector
(USB)
E*
Power Expansion module connector
C*
SW3 Panel switch
NOTE: Items marked with * are accessible only after removing the Power Expansion module.

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 13 of 26
3. External Connectors
3.1. Serial Port Connector (RS-XXX)
The TEP-0700-IMX7 has a dual non-galvanic isolated 2-wire RS-232 serial port.
RS-XXX:
Pin #
Signal
Description
Device
1
GND
Ground
2
SERIAL1A_TXD
Port#1A Transmit data (output)
ttymxc1
3
SERIAL1A_RXD
Port#1A Receive data (input)
ttymxc1
4
NC
5
NC
6
GND
Ground
7
SERIAL1B_TXD
Port#1B Transmit data (output)
ttymxc2
8
SERIAL1B_RXD
Port#1B Receive data (input)
ttymxc2
9
NC
10
NC
Header on TEP-0700-IMX7: Molex 43045-1012 (10-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1000 (10-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 14 of 26
3.2. CAN Bus Connector (CANBus)
The TEP-0700-IMX7 has two non-galvanic isolated CAN Bus interfaces.
CANBus:
Pin #
Signal
Description
Interface
1
GND_CAN
Ground for CAN
2
CAN1A_TERM_P
To enable CAN1A Termination, bridge with CAN1A_P
can0
3
CAN1A_P
CAN Bus 1A high (-24~+24V)
can0
4
CAN1A_N
CAN Bus 1A low (-24~+24V)
can0
5
CAN1A_TERM_N
To enable CAN1A Termination, bridge with CAN1A_N
can0
6
NC
7
GND_CAN
Ground for CAN
8
CAN1B_TERM_P
To enable CAN1B Termination, bridge with CAN1B_P
can1
9
CAN1B_P
CAN Bus 1B high (-24~+24V)
can1
10
CAN1B_N
CAN Bus 1B low (-24~+24V)
can1
11
CAN1B_TERM_N
To enable CAN1B Termination, bridge with CAN1B_N
can1
12
NC
Header on TEP-0700-IMX7: Molex 43045-1212 (12-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1200 (12-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
3.3. Digital I/O Connectors (GPIO1/GPIO2)
The TEP-0700-IMX7 has two non-galvanic isolated GPIO Expansion headers with the following pinout:
GPIO1:
Pin
#
Signal
Description
Voltage
Current
Max.
GPIO
Kernel
GPIO
Bank/IO
Min.
Typ.
Max.
1
GPIO1A
DIG_IN1/OUT1
-0.3V
3.3V
3.6V
0.66mA
140
5_12
2
GPIO1B
DIG_IN2/OUT2
-0.3V
3.3V
3.6V
0.66mA
141
5_13
3
GND_DIO
Ground for digital I/O
4
NC
5
GPIO1C
DIG_IN5/OUT5
-0.3V
3.3V
3.6V
0.66mA
130
5_2
6
GPIO1D
DIG_IN5/OUT6
-0.3V
3.3V
3.6V
0.66mA
36
2_4
7
VCC_DIO
Supply output for digital I/O
3.3V
8
NC

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 15 of 26
GPIO2:
Pin
#
Signal
Description
Voltage
Current
Max.
PWM
(default)
GPIO*
Kernel
GPIO
Bank/IO
Min.
Typ.
Max.
1
GPIO2A
ADCI_INO
-0.3V
3.3V
2
GPIO2B
PWM_OUT or
DIG_IN2/OUT2
-0.3V
3.3V
3.6V
0.66mA
1
8
1_8
3
GND_DIO
Ground for digital
I/O
4
NC
5
GPIO2C
PWM_OUT or
DIG_IN5/OUT5
-0.3V
3.3V
3.6V
0.66mA
2
9
1_9
6
GPIO2D
PWM_OUT or
DIG_IN6/OUT6
-0.3V
3.3V
3.6V
0.66mA
4
11
1_11
7
VCC_DIO
Supply output
3.3V
8
NC
NOTE: GPIO2 port is set by default as PWM. GPIO setting requires software modification. Please
connect with TechNexion support team for more details.
Header on TEP-0700-IMX7: Molex 43045-0812 (8-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-0800 (8-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
3.4. S1 Button
The TEP-0700-IMX7 by default boots the unit from internal flash storage (eMMC). By pressing the “S1”
button before applying power to the unit and keeping the button pressed for 10 seconds, the unit will boot
from an alternative boot media (microSD card).
3.5. RST Button
The TEP-0700-IMX7 features a “RST” button for system reset.
3.6. LED Light Indicator
The TEP-0700-IMX7 has one programmable LED Light indicator.
LED #
Color
GPIO Kernel
GPIO Bank/IO
1
Green
179
6_19

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 16 of 26
3.7. USB OTG (Type-C) Connector
The TEP-0700-IMX7 has one USB Type-C connector (USB 2.0 signals only) that can be used to connect
a host computer to the unit for programming and update purposes.
Pin
#
Signal
Description
Pin
#
Signal
Description
A1
GND
Ground
B1
GND
Ground
A2
NC
B2
NC
A3
NC
B3
NC
A4
VBUS
5V Universal Serial Bus Power
B4
VBUSD
5V Universal Serial Bus Power
A5
CC1
OTG detection signal
B5
CC2D
OTG detection signal
A6
USB_D+
USB differential pair signal
port 1
B6
USB_D+
USB differential pair signal
port 2
A7
USB_D-
B7
USB_D-
A8
NC
B8
NC
A9
VBUS
5V Universal Serial Bus Power
B9
VBUSD
5V Universal Serial Bus Power
A10
NC
B10
NC
A11
NC
B11
NC
A12
GND
Ground
B12
GND
Ground
3.8. MicroSD Card Slot
The TEP-0700-IMX7 features a standard microSD card slot which is connected to the NXP i.MX7
integrated “Ultra Secured Digital Host Controller” (uSDHC).
The following main features are supported by uSDHC:
•Compatible with the MMC System Specification version 4.2/4.3/4.4/4.41/5.0.
•Conforms to the SD Host Controller Standard Specification version 3.0.
•Compatible with the SD Memory Card Specification version 3.0 and supports the “Extended
Capacity SD Memory Card”.
•Compatible with the SDIO Card Specification version 3.0.
•Supports 1-bit / 4-bit SD and SDIO modes
The MMC/SD/SDIO host controller can support a single MMC / SD / SDIO card or device.
3.9. Nano-SIM Card Slot
The TEP-0700-IMX7 features an external Nano-SIM card slot for use by 3G/4G/LTE wireless module.
NOTE: This card slot can be only used by a M.2 3G/4G/LTE module installed into the M.2 connector. The
M.2 connector can be found at location “B” in chapter 4. Internal Connectors and Expansion Options of
this manual. No M.2 3G/4G LTE module is included in this device (must be purchased separately, not
sold by TechNexion).

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 17 of 26
3.10. Gigabit Ethernet Interface
The TEP-0700-IMX7 by default comes with two Gigabit Ethernet RJ45 connectors. LAN1 connector can
support 802.3at Power over Ethernet functionality if configured with the PoE power option (TEP0700-
IMX7x-Rxx-Exx-LPOE-xxxx) by connecting it to an 802.3at compliant PoE switch or power injector.
LAN1 / LAN2:
Pin #
1000 Mbps
100 Mbps
10 Mbps
1
MDI0+
Transmit Data+
Transmit Data+
2
MDI0-
Transmit Data-
Transmit Data-
3
MDI1+
Receive Data+
Receive Data+
4
MDI2+
5
MDI2-
6
MDI1-
Receive Data-
Receive Data-
7
MDI3+
8
MDI3-
3.11. USB Host Connector
The TEP-0700-IMX7 has a standard single USB Host connector (USB 2.0 signals only) to connect to a
USB peripheral such as a keyboard, mouse, USB storage device or USB hub.
3.12. Power Input Connector
The TEP-0700-IMX7 can be powered either over the DC INPUT connector or PoE over the RJ45 LAN1
port.
NOTE: Do not power the unit by DC input when you apply power over the Power over Ethernet (RJ45)!
Pin #
Signal
Description
1
GND
Ground
2
VCC
DC Voltage input (12V/24V/8~36VDC)
Header on TEP-0700-IMX7: Molex 43045-0212 (2-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-0200 (2-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 18 of 26
3.13. Grounding
The TEP-0700-IMX7 must always be grounded to the earth. Grounding helps to limit the effects of noise
due to electromagnetic interference on the device. The earth connection will have to be done using the
grounding screw. The screw for the ground connection is marked with an engraved ground symbol.
3.14. Antenna Holes
There are six antenna holes (two each on the rear side, on the right side and on the top side) available.
They come fitted with breakaway metal tabs. In order to utilize them, the tabs must be removed by
carefully using pincers or pliers.

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 19 of 26
4. Internal Connectors and Expansion Options
Rear view (opened device) without the Power Expansion module:
A
E*
B*
C*
D*
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
D*
SW2 Panel switch
B*
M.2 KEY-B 3G/4G LTE module connector
(USB)
E*
Power Expansion module connector
C*
SW3 Panel switch
NOTE: Items marked with * are accessible only after removing the Power Expansion module.
4.1. RTC Battery Connector
The TEP-0700-IMX7 has an internal RTC backup battery connector (Marked A).
Pin #
Signal
Description
1
RTC_VCC
3V (connect to standard CR2032 battery)
2
GND
Ground

TEP-0700-IMX7 HARDWARE MANUAL –VER 1.00 –MAR 11 2019
Page 20 of 26
Header on TEP-0700-IMX7: Molex 53047-0210 (1.25mm Pitch PicoBlade Wire-to-Board Header).
Cable receptacle: Molex 051021-8602 (1.25mm Pitch PicoBlade Wire-to-Wire and Wire-to-Board Housing)
plug with crimp contact Molex 50058-8000.
Battery P/N: KTS BCR2032H14.0AM1XB.
4.2. M.2 KEY-B 3G/4G LTE Module Connector
The TEP-0700-IMX7 has an internal M.2 KEY-B 3G/4G LTE module (USB 2.0 signals) connector (Marked
B). M.2 cards in the industry-standard M.2 KEY-B 3042 (30 x 42 mm) or M.2 KEY-B 2242 (22 x 42 mm)
form factor are supported.
4.3. SW3 Panel Backlight Switch
The TEP-0700-IMX7 has an internal SW3 Panel Backlight switch (Marked C). Always use the default
settings.
Pin #
5” Panel
7” Panel (default)
1-2
OFF
ON
4.4. SW2 Panel Scanning Direction Switch
The TEP-0700-IMX7 has an internal SW2 Panel Scanning Direction switch (Marked D). Always use the
default settings.
Pin #
5” Panel
7” Panel (default)
Description
1-8
ON
OFF
Down to Up
2-7
OFF
OFF
Up do Down
3-6
OFF
OFF
Left to Right
4-5
OFF
OFF
Right to Left