TechNexion TOUCAN TC-0710 SLIM HMI User manual

3.1 Cut-out Dimensions
3.2 VESA Mounng
TC-0700 / TC-0710
Quickstart Guide
3 Installaon Instrucons
This secon describes the mounng procedures for the TOUCAN series device. The material in the mounng area
must provide sufficient strength for support of this HMI.
This device is compable with VESA MIS-C Standard 35*75mm. There are 4 VESA MIS-C (M4) mounng holes on
the rear side of the device. M4 screws with at least 6mm head-to-p length are required to secure this device.
INNOVATORS OF TECHNOLOGY
TC-0700 TC-0710
TC-0700 TC-0710
2 Dimensions
TC-0700 TC-0710
198.5
136.3
1 Safety Precauons
Thank you for purchasing a TechNexion TOUCAN series device. This installaon guide will be helpful in the
installaon, wiring and inspecon of your TechNexion HMI. Before using the product, please read this guide to
ensure correct use. You should thoroughly understand all safety precauons before proceeding with the installaon,
wiring, and operaon. Place this instrucon sheet in a safe locaon for future reference.
• Keep the device dry. Precipitaon, humidity, and all types of liquids or moisture can contain minerals that will
corrode electronic circuits. If your device does get wet, allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage
baeries, and warp or melt certain plascs.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form
inside the device and damage electronic circuit boards.
• Do not aempt to open the device.This product needs to be installed by qualified personnel.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not paint the device. Paint can clog the parts and prevent proper operaon.
• Unauthorized modificaons or aachments could damage the device and may violate regulaons governing radio
devices.
• Do not touch any internal or exposed parts of the device as electrical shock may result.
• Do not open the device while power is on. Otherwise electrical shock may result.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Be sure the venlaon holes are not obstructed during operaon. Otherwise malfuncon may result due to
bad venlaon or overheang.
These suggesons apply equally to your device, baery, charger, or any enhancement. If any device is not
working properly, take it to the nearest authorized service facility for service.
• Make sure that the available power source matches the required input power of the device. Failure to observe
this cauon may result in electric shock or fire.
• Do not power the unit by DC input when you apply power over the PoE (RJ45).
1.1 Storage and Installaon
1.2 Wiring
1.3 Maintenance and Inspecon
!Unit : mm
Unit : mm
173
100
29.6
122.1
92.6
95.3
184.3 47.7
173
100
1 2

3.3 Rear Mounng and Mounng Clips Installaon
3.4 Surface Mounng Installaon (TC-0710 only)
4 External Connectors
There are 8 mounng holes (M4) on the rear side of the device required for surface mounng. M4 screws with at
least 6mm head-to-p length are required to secure this device.
There are 6 mounng clips required for rear mounng.
• All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmied, in any
form or by any means whether, electronic, mechanical, or otherwise without the prior wrien permission of TechNexion Ltd.
• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied
by law no liability (including liability to any person by reason of negligence) will be accepted by TechNexion Ltd., its subsidiaries or
employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version
at: hps://www.technexion.com/support/download-center/
TC-0710
TC-0700 TC-0710
TC-0700
1234567
8
9
10
11
1 2 3 4 567
8
9
10
11
Description No.No. Description
1 LAN RJ45 and PoE connector
2 Power Input (10~30VDC) connector
3 GPIO connector
4 USB Host connector
5HDMI connector
6 CAN Bus connector
7RS-XXX (Serial Port) connector
8 MicroSD cardslot
9USB OTG connector
10 S1 Boot Select button
11 Reset button
Phone: [phone]
Web: www.technexion.com
16F-5, No. 736, Zhongzheng Road,
ZhongHe District, 23511, New Taipei City, Taiwan
© 2001-2018 TechNexion Ltd.
2018-11-05
5.1 Serial Port Connector (RS-XXX)
5 Pin Definion
Header: Molex 43045-1000 (10-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1000 (10-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
Shielding with 6.3mm male spade terminal connector.
Port Pin # RS-232 + RS-232 RS-232 + RS-422 RS-232 + RS-485
Device
1 GND GND GND
ttymxc0
ttymxc0
ttymxc0
ttymxc0
ttymxc1
ttymxc1
ttymxc1
ttymxc1
2SERIAL1A_TXD SERIAL1A_TXD SERIAL1A_TXD
3SERIAL1A_RXD SERIAL1A_RXD SERIAL1A_RXD
4SERIAL1A_RTS SERIAL1A_RTS SERIAL1A_RTS
5SERIAL1A_CTS SERIAL1A_CTS SERIAL1A_CTS
6 GND GND GND
7SERIAL1B_TXD SERIAL1B_TXD+ SERIAL1B+
8 SERIAL1B_RXD SERIAL1B_RXD NC
NC
SERIAL1B-
9 SERIAL1B_RTS SERIAL1B_RXD+
SERIAL1B_TXD-10 SERIAL1B_CTS
12345
678910
5.2 CAN Bus Connector (CANBus)
Header: Molex 43045-1200 (12-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1200 (12-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
Shielding with 6.3mm male spade terminal connector.
GND_CAN
CAN1A_TERM_P can0
CAN1A_P can0
CAN1A_N can0
CAN1A_TERM_N can0
NC
GND_CAN
CAN1B_TERM_P can1
CAN1B_P can1
CAN1B_N can1
CAN1B_TERM_N can1
NC
Port Pin # Signal Interface
1
2
3
4
5
7
6
8
9
10
11
12
123456
789101112
5.3 Digital I/O Connector (GPIO)
Header: Molex 43045-0800 (8-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-0800 (8-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
Shielding with 6.3mm male spade terminal connector
Port Pin #
GPIO Signal GPIO Description
Voltage
1 GPIO1A 1.2V
1.2V
5~34V
5~34V
5~34V
10~30V
DIG_IN1
2 GPIO1B DIG_IN2
3 GND_DIO
Ground for digital I/O
Common Ground
4 NC
5 GPIO1C DIG_OUT1
6 GPIO1D DIG_OUT2
7VCC_DIO Supply output for digital I/O
Supply output (based on VDC)8 VCC
1234
5678
The unit is preloaded with soware that can download and install a selecon of OS images over hardwired
network. Simply connect a network to the unit through the Ethernet LAN RJ45 connector and power it up, then
follow the steps on the screen to load the soware. Local proxies will interfere with this process. For more
informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowledge-base/
6 Soware Installaon
3 4